Hi Ken, What is connecting to this interface...you may want to manually configure the duplex and speed settings on this interface to match that of the device that is connecting to it. Also be very wary if you have a hub connected.!!!
Let me know if this helps ! Troy Ken Diliberto wrote: > > Here's more information I should have included in the first > message: > > #sh int f0/13 > FastEthernet0/13 is up, line protocol is up > Hardware is Fast Ethernet, address is 00d0.bbd2.260d (bia > 00d0.bbd2.260d) > MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec, > reliability 255/255, txload 1/255, rxload 1/255 > Encapsulation ARPA, loopback not set > Keepalive not set > Auto-duplex (Full), Auto Speed (100), 100BaseTX/FX > ARP type: ARPA, ARP Timeout 04:00:00 > Last input never, output 00:00:00, output hang never > Last clearing of "show interface" counters 12:58:47 > Queueing strategy: fifo > Output queue 0/40, 0 drops; input queue 0/75, 0 drops > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 6000 bits/sec, 5 packets/sec > 218510 packets input, 78936683 bytes > Received 1073 broadcasts, 0 runts, 0 giants, 0 throttles > 147 input errors, 147 CRC, 0 frame, 0 overrun, 0 ignored > 0 watchdog, 538 multicast > 0 input packets with dribble condition detected > 467270 packets output, 258862433 bytes, 0 underruns > 0 output errors, 0 collisions, 2 interface resets > 0 babbles, 0 late collision, 0 deferred > 0 lost carrier, 0 no carrier > 0 output buffer failures, 0 output buffers swapped out > I did a clear count f0/13 last night. Input and CRC errors > were rising > at a moderate rate. > > interface FastEthernet0/13 > no logging event link-status > port storm-control broadcast trap > switchport access vlan 8 > no snmp trap link-status > spanning-tree portfast > ! > > Feb 24 16:02:31.046: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:06:08.951: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:07:29.785: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:12:01.748: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:20:46.733: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:21:51.812: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:25:11.507: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:27:54.890: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:28:55.370: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:30:30.011: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:40:03.346: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:41:24.389: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:42:57.809: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 16:48:08.352: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 17:47:18.451: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 17:48:45.262: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 17:59:49.059: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 18:35:33.480: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 18:37:06.128: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > Feb 24 18:38:06.935: %LINK-4-ERROR: FastEthernet0/13 is > experiencing > errors > > > >>> "The Long and Winding Road" > > 02/24/03 11:20PM >>> > ""Ken Diliberto"" wrote in message > news:[EMAIL PROTECTED] > > I had a strange problem this evening with a 2924XL. The > server > attached > > to port f0/13 had been generating errors and finally the > switch > stopped > > talking to it. A shut/no shut combination started everything > back > up > > again. > > > > The configuration only says to send a trap when a broadcast > storm > > happens. There isn't anything about excessive errors. > > > > Any thoughts? I haven't checked CCO. I don't have a good > idea what > to > > search for without getting 10,000,000,000 hits. > > > what is the exact configuration line used? the documentation > talks > about > default rising and falling thresholds. of course it does not > indicate > whether or not the default is to shutdown or not. > > http://www.cisco.com/univercd/cc/td/doc/product/lan/c2900xl/29_35wc3/cref/cl > > icmds.htm#xtocid51 > > > > > > > > > > Thanks. > > > > Ken > > Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=63733&t=63680 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
