Ah I see the problem now. You should delete the many pvc's you have configured on the ls100 relating to 48 and 49 and then use this one command.
pvc est 1 2 0 2 48 512 0 155 2 2 49 512 0 155 This assumes that pvc 2/48 is associated with port 0 and 2/49 is associated with port 2. Ensure your routers are configured with this setup as well. The problem is the config you have currently setups end to end pvcs as 48 to 49 and 49 to 49 but what you need is 48 to 49 and 49 to 48. Thanks, Ian www.ccie4u.com Rack Rentals and Lab Scenarios -----Original Message----- From: Xy Hien Le [mailto:[EMAIL PROTECTED] Sent: Tuesday, March 18, 2003 12:38 AM To: [EMAIL PROTECTED] Subject: Re: ATM LS100 PROBLEM! [7:65585] Hi, I have tried but failed to make the connection. rA connected to port 0 of the ls100 rB connected to port 2 of the ls100 here is the configuration of the ls100: Show pvc 0: Bandwidth Available (Forward/Backward/Line Rate): 155.0 / 155.0 / 155.0 Mbps Existing connections : 0 (Uni), 2 (Bi), 0 (Multipoint), 2 (Gateway) LowLine LowVPI LowVCI HiLine HiVPI HiVCI TrfType CONNECTION 0 0 5 16 0 2 UBR-BE Gateway 0 0 16 16 0 3 UBR-BE Gateway 0 2 48 2 2 48 UBR-BE Bi 0 2 49 2 2 49 UBR-BE Bi Show pvc 2: Bandwidth Available (Forward/Backward/Line Rate): 155.0 / 155.0 / 155.0 Mbps Existing connections : 0 (Uni), 2 (Bi), 0 (Multipoint), 2 (Gateway) LowLine LowVPI LowVCI HiLine HiVPI HiVCI TrfType CONNECTION 2 0 5 16 0 2 UBR-BE Gateway 2 0 16 16 0 3 UBR-BE Gateway 2 2 48 0 2 48 UBR-BE Bi 2 2 49 0 2 49 UBR-BE Bi here is the debug of the atm interface: 00:20:27: ILMI(ATM5/0): Received Interface Up 00:20:27: ILMI(ATM5/0): Sending ilmiColdStart trap 00:20:27: ILMI(ATM5/0): No ILMI VC found 00:20:27: ILMI: Encapsulation error on o/g ILMI Pdu (ATM5/0) 00:20:27: ILMI: Unable to Send Pdu out 00:20:27: ATMSIG: startatmsig_ilmi_timer 00:20:28: %LINK-3-UPDOWN: Interface ATM5/0, changed state to up 00:20:29: ILMI(ATM5/0): Sending ilmiColdStart trap 00:20:29: ILMI(ATM5/0): Querying peer device type. 00:20:29: ILMI:peerDeviceTypeQuery not completed 00:20:29: ILMI:peerPortTypeQuery not completed 00:20:29: ILMI(ATM5/0): From Restarting To WaitDevAndPort 00:20:29: ILMI(ATM5/0):Sending out Request 20 00:20:29: ILMI(ATM5/0):Sending out Request 21 00:20:29: ILMI(ATM5/0):Response received for request 20 00:20:29: ILMI(ATM5/0): Errored response Function Type = ilmiPeer DeviceTypeInfo 00:20:29: ILMI(ATM5/0):Response received for request 21 00:20:29: The peer UNI Type on (ATM5/0) is 2 00:20:29: ILMI(ATM5/0): From WaitDevAndPort To DeviceAndPortComplete 00:20:29: ILMI(ATM5/0): From DeviceAndPortComplete To NodeConfigComplete 00:20:29: ILMI: Assigning default device type (ATM5/0) 00:20:29: ILMI: My Device type is set to User-side (ATM5/0) 00:20:29: ILMI(ATM5/0): Checking Peer Config and Address Table 00:20:29: ILMI:peerAddressTableCheck not completed 00:20:29: ILMI:peerConfigQuery not completed 00:20:29: ILMI:peerRangeConfigQuery not completed 00:20:29: ILMI(ATM5/0): From NodeConfigComplete To AwaitRestartAck 00:20:29: ILMI(ATM5/0):Sending out Request 22 00:20:29: ILMI(ATM5/0):Sending out Request 23 00:20:29: ILMI(ATM5/0):Sending out Request 24 00:20:29: ILMI(ATM5/0):Sending out Request 25 00:20:29: ILMI(ATM5/0):Response received for request 22 00:20:29: ILMI(ATM5/0): Errored response Function Type = ilmiAddr essTableCheck 00:20:29: ILMI(ATM5/0):Response received for request 23 00:20:29: ILMI(ATM5/0): The Maximum # of VPI Bits is 4 00:20:29: ILMI(ATM5/0): The Maximum # of VCI Bits is 8 00:20:29: ILMI(ATM5/0): The UNI version is negotiated as ilmiUniVersionUnsupport ed 00:20:29: ILMI(ATM5/0):Response received for request 24 00:20:29: ILMI(ATM5/0): Errored response Function Type = ilmiPeer RangeConfigQuery 00:20:29: ILMI: Bad peer Range Values for peer. Setting ILMI_NOT_AVAILABLE 00:20:29: ILMI(ATM5/0): From AwaitRestartAck To UpAndNormal 00:20:29: ILMI: Auto Port determination enabled 00:20:29: atmsig_ilmi_callback: uni version 2 00:20:29: ATMSIG: sscop open successful 00:20:29: ILMI(ATM5/0): Link determination completed 00:20:29: Peer Device Type: ilmiDeviceTypeUser 00:20:29: Peer Port Type: ilmiUniTypePrivate 00:20:29: Peer MaxVpiBits: 4 00:20:29: Peer MaxVciBits: 8 00:20:29: Peer MaxVpcs: 65536 00:20:29: Peer MaxVccs: 65536 00:20:29: Peer MaxSvpcVpi: 65536 00:20:29: Peer MaxSvccVpi: 65536 00:20:29: Peer MinSvccVci: 65536 00:20:29: Peer UNI version: ilmiUniVersion3point0 00:20:29: Neg. UNI Version: ilmiUniVersionUnsupported 00:20:29: Local Device Type: ilmiDeviceTypeUser 00:20:29: Local Port Type: ilmiPrivateUNIUserSide 00:20:29: Local System ID: 00:20:29: ILMI(ATM5/0): KeepAlive disabled 00:20:29: ILMI(ATM5/0):Response received for request 25 00:20:29: ILMI(ATM5/0): Errored response Function Type = ilmiPeer MgmtInfo 00:20:29: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM5/0, changed state to up 00:20:39: ATMSIG-IF:atmSig_clearAllSvc: Port ID : ATM5/0 Interface Reset 00:20:44: Trap Sent: Waiting for prefix (ATM5/0) 00:20:44: ILMI(ATM5/0): Sending ilmiColdStart trap 00:20:44: ILMI: Validating address 47.0000.0000.0001.0000.0000.0000 00:20:44: ILMI: Clients Registered but none to validate 00:20:44: ILMI: Address considered validated (ATM5/0) 00:20:44: ILMI: Address added : 47.0000.0000.0001.0000.0000.0000 (ATM5/0) 00:20:44: %LANE-6-INFO: ATM5/0: ILMI prefix add event received 00:21:12: ILMI(ATM5/0): Trap Received 00:21:12: ILMI: Notifying trap to client 00:21:12: ILMI: Validating address 47.0000.0000.0001.0000.0000.0000 00:21:12: ILMI: Clients Registered but none to validate 00:21:12: ILMI: Address considered validated (ATM5/0) 00:21:12: ILMI: Address added : 47.0000.0000.0001.0000.0000.0000 (ATM5/0) 00:21:12: %LANE-6-INFO: ATM5/0: ILMI prefix add event received rA(config-if)#sh rA(config-if)# 00:21:33: ILMI(ATM5/0): Received Interface Down. Shutting down ILMI 00:21:33: ATMSIG-IF:atmSig_clearAllSvc: Port ID : ATM5/0 Interface Reset 00:21:33: ATMSIG-IF:atmSig_clearAllSvc: Port ID : ATM5/0 Interface Reset 00:21:35: %LINK-5-CHANGED: Interface ATM5/0, changed state to administratively d own 00:21:36: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM5/0, changed state to downno sh rA(config-if)# 00:21:40: ILMI(ATM5/0): Received Interface Up 00:21:40: ILMI(ATM5/0): Sending ilmiColdStart trap 00:21:40: ILMI(ATM5/0): No ILMI VC found 00:21:40: ILMI: Encapsulation error on o/g ILMI Pdu (ATM5/0) 00:21:40: ILMI: Unable to Send Pdu out 00:21:40: ATMSIG: startatmsig_ilmi_timer 00:21:41: %LINK-3-UPDOWN: Interface ATM5/0, changed state to up 00:21:42: ILMI(ATM5/0): Sending ilmiColdStart trap 00:21:42: ILMI(ATM5/0): Querying peer device type. 00:21:42: ILMI:peerDeviceTypeQuery not completed 00:21:42: ILMI:peerPortTypeQuery not completed 00:21:42: ILMI(ATM5/0): From Restarting To WaitDevAndPort 00:21:42: ILMI(ATM5/0):Sending out Request 26 00:21:42: ILMI(ATM5/0):Sending out Request 27 00:21:42: ILMI(ATM5/0):Response received for request 26 00:21:42: ILMI(ATM5/0): Errored response Function Type = ilmiPeer DeviceTypeInfo 00:21:42: ILMI(ATM5/0):Response received for request 27 00:21:42: The peer UNI Type on (ATM5/0) is 2 00:21:42: ILMI(ATM5/0): From WaitDevAndPort To DeviceAndPortComplete 00:21:42: ILMI(ATM5/0): From DeviceAndPortComplete To NodeConfigComplete 00:21:42: ILMI: Assigning default device type (ATM5/0) 00:21:42: ILMI: My Device type is set to User-side (ATM5/0) 00:21:42: ILMI(ATM5/0): Checking Peer Config and Address Table 00:21:42: ILMI:peerAddressTableCheck not completed 00:21:42: ILMI:peerConfigQuery not completed 00:21:42: ILMI:peerRangeConfigQuery not completed 00:21:42: ILMI(ATM5/0): From NodeConfigComplete To AwaitRestartAck 00:21:42: ILMI(ATM5/0):Sending out Request 28 00:21:42: ILMI(ATM5/0):Sending out Request 29 00:21:42: ILMI(ATM5/0):Sending out Request 30 00:21:42: ILMI(ATM5/0):Sending out Request 31 00:21:42: ILMI(ATM5/0):Response received for request 28 00:21:42: ILMI(ATM5/0): Errored response Function Type = ilmiAddr essTableCheck 00:21:42: ILMI(ATM5/0):Response received for request 29 00:21:42: ILMI(ATM5/0): The Maximum # of VPI Bits is 4 00:21:42: ILMI(ATM5/0): The Maximum # of VCI Bits is 8 00:21:42: ILMI(ATM5/0): The UNI version is negotiated as ilmiUniVersionUnsupport ed 00:21:42: ILMI(ATM5/0):Response received for request 30 00:21:42: ILMI(ATM5/0): Errored response Function Type = ilmiPeer RangeConfigQuery 00:21:42: ILMI: Bad peer Range Values for peer. Setting ILMI_NOT_AVAILABLE 00:21:42: ILMI(ATM5/0): From AwaitRestartAck To UpAndNormal 00:21:42: ILMI: Auto Port determination enabled 00:21:42: atmsig_ilmi_callback: uni version 2 00:21:42: ATMSIG: sscop open successful 00:21:42: ILMI(ATM5/0): Link determination completed 00:21:42: Peer Device Type: ilmiDeviceTypeUser 00:21:42: Peer Port Type: ilmiUniTypePrivate 00:21:42: Peer MaxVpiBits: 4 00:21:42: Peer MaxVciBits: 8 00:21:42: Peer MaxVpcs: 65536 00:21:42: Peer MaxVccs: 65536 00:21:42: Peer MaxSvpcVpi: 65536 00:21:42: Peer MaxSvccVpi: 65536 00:21:42: Peer MinSvccVci: 65536 00:21:42: Peer UNI version: ilmiUniVersion3point0 00:21:42: Neg. UNI Version: ilmiUniVersionUnsupported 00:21:42: Local Device Type: ilmiDeviceTypeUser 00:21:42: Local Port Type: ilmiPrivateUNIUserSide 00:21:42: Local System ID: 00:21:42: ILMI(ATM5/0): KeepAlive disabled 00:21:42: ILMI(ATM5/0):Response received for request 31 00:21:42: ILMI(ATM5/0): Errored response Function Type = ilmiPeer MgmtInfo 00:21:42: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM5/0, changed state to up 00:21:52: ATMSIG-IF:atmSig_clearAllSvc: Port ID : ATM5/0 Interface Reset 00:21:57: Trap Sent: Waiting for prefix (ATM5/0) 00:21:57: ILMI(ATM5/0): Sending ilmiColdStart trap 00:21:57: ILMI: Validating address 47.0000.0000.0001.0000.0000.0000 00:21:57: ILMI: Clients Registered but none to validate 00:21:57: ILMI: Address considered validated (ATM5/0) 00:21:57: ILMI: Address added : 47.0000.0000.0001.0000.0000.0000 (ATM5/0) 00:21:57: %LANE-6-INFO: ATM5/0: ILMI prefix add event received I don't know what I did wrong? Xy ----- Original Message ----- From: "Sales" To: "'Xy Hien Le'" Cc: Sent: Monday, March 17, 2003 6:48 PM Subject: RE: ATM LS100 PROBLEM! [7:65585] > Hi Xy, > > Here is a sample command to add pvc 2/48 to the ls100 ports #0 and #2 > > pvc est 1 2 0 2 48 512 0 155 2 2 48 512 0 155 > > > Thanks, > > Ian > > http://www.ccie4u.com > > > > -----Original Message----- > From: Xy Hien Le [mailto:[EMAIL PROTECTED] > Sent: Monday, March 17, 2003 11:36 PM > To: [EMAIL PROTECTED] > Subject: Re: ATM LS100 PROBLEM! [7:65585] > > Hi Ian, > > Thanks for your help previously. The configuration for NSAP was working. > This is a new issue. I tried to connect the 2 routers as stated via the > LS100 for PVC connection. > I have no idea how to do it with the LS100. > Could you please do a sample according to the configuration of the 2 ATM > routers as stated in my posted email? > I don't know how to set up a bidirectional pvc on the ls100 at all, it > keep > giving me the error message of illegal number!!! > Please help. > Thanks, > Xy > > ----- Original Message ----- > From: "Sales" > To: "'Xy Hien Le'" ; > Sent: Monday, March 17, 2003 5:17 PM > Subject: RE: ATM LS100 PROBLEM! [7:65585] > > > > Hi Xy, > > > > I had sent you configuration information for the LS100 using NSAPs and > > thought you had it working now. Is this a new issue? If so it should > > be a straight matter of just setting up a bidirectional pvc on the > ls100 > > for your pvc. Bear in mind there are reserved ranges for vpi's/vci's > > when configuring your pvc. > > > > > > Thanks, > > > > Ian > > > > www.ccie4u.com > > Rack rentals and lab scenarios > > > > > > -----Original Message----- > > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf > Of > > Xy Hien Le > > Sent: Monday, March 17, 2003 9:15 AM > > To: [EMAIL PROTECTED] > > Subject: ATM LS100 PROBLEM! [7:65585] > > > > Hi all, > > > > I have an LS100 ATM LIGHTSTREAM (NOT LS1010) in between 2 ATM routers > > configured as follow: > > > > interface ATM2/0 > > ip address 10.1.1.2 255.255.255.0 > > ip ospf network point-to-multipoint > > map-group atm > > atm pvc 1 0 16 ilmi > > atm pvc 2 2 48 aal5snap > > no atm ilmi-keepalive > > > > map-list atm > > ip 10.1.1.1 atm-vc 2 broadcast > > > > > > ATM SWITCH LS100 IN BETWEEN > > > > > > > > interface ATM2/0 > > ip address 10.1.1.1 255.255.255.0 > > ip ospf network point-to-multipoint > > map-group atm > > atm pvc 1 0 16 ilmi > > atm pvc 2 2 49 aal5snap > > no atm ilmi-keepalive > > > > map-list atm > > ip 10.1.1.2 atm-vc 2 broadcast > > ! > > > > I don't know how to configure the LS100 LIGHTSTREAM SWITCH to connect > > the 2 > > routers. > > Can someone with the experience of LS100 send me a configuration of > this > > switch? > > > > Thank you all in advance. > > > > Xy [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=65647&t=65585 -------------------------------------------------- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
