Mostly stable releases a week or so after non RC is released... On Fri, Aug 10, 2012 at 11:39 AM, David Cole <[email protected]> wrote: > Have you even used a "nightly CMake" from the last month or so, or > have you only been using release candidates and official releases? > > > On Fri, Aug 10, 2012 at 2:35 PM, J Decker <[email protected]> wrote: >> Ya, unfortunatly I don't have the specific case that was failing >> anymore... it's probably because I've been using the same build output >> since 2.8.6 and just keep updating cmake... last couple versions have >> actually gone smoothly >> >> >> On Fri, Aug 10, 2012 at 4:21 AM, David Cole <[email protected]> wrote: >>> Can you try again with a nightly build of CMake? >>> >>> There's a change that we did not take that *is* in the nightly build, >>> but is not in the 2.8.9 release. I'd like to know if that change is >>> responsible for this behavior. >>> >>> We were uncertain of this commit [ >>> http://cmake.org/gitweb?p=cmake.git;a=commitdiff;h=e16f58ddd6aea9bebc6b4a914eed54cf7517ff61 >>> ] ... so it did not go into the 2.8.9 release. >>> >>> >>> Thx, >>> David >>> >>> >>> On Thu, Aug 9, 2012 at 7:33 PM, J Decker <[email protected]> wrote: >>>> After considering this a bit more I went to this >>>> C:\GENERAL\BUILD\VS10-X86\ALTANIK\CMAKEFILES directory adn removed >>>> Build*. and then everything built correctly. And BuildXXXXX did not >>>> come back. So maybe i've been changing cmake versions too much.... >>>> going to grab the 2.8.9 now anway. >>>> >>>> On Thu, Aug 9, 2012 at 4:27 PM, J Decker <[email protected]> wrote: >>>>> I'm having a little difficulty figuring out why this is not building >>>>> my projects using visual studio/msbuild. Basically all I get is >>>>> "========== Build: 0 succeeded, 0 failed, 24 up-to-date, 0 skipped >>>>> ==========" >>>>> >>>>> I've used MSBuild with /v:diag set and in the huge log that that >>>>> generates.... >>>>> >>>>> Outputs for >>>>> C:\GENERAL\BUILD\VS10-X86\ALTANIK\CMAKEFILES\D460CDD940FC411117A7C12689E8CBDF\BUILDCORE.RULE|M:\ALTANIK\CMAKE_ALL\CMAKELISTS.TXT: >>>>> (TaskId:43) >>>>> C:\GENERAL\BUILD\VS10-X86\ALTANIK\CMAKEFILES\GENERATE.STAMP >>>>> (TaskId:43) >>>>> C:\GENERAL\BUILD\VS10-X86\ALTANIK\CMAKEFILES\BUILDCORE (TaskId:43) >>>>> All outputs are up-to-date. (TaskId:43) >>>>> >>>>> How do I make sure that 'add_custom_target' is built? and I shouldn't >>>>> have to ask that because the docs say.... >>>>> >>>>> "Adds a target with the given name that executes the given commands. >>>>> The target has no output file and is ALWAYS CONSIDERED OUT OF DATE >>>>> even if the commands try to create a file with the name of the >>>>> target." >>>>> >>>>> >>>>> >>>>> >>>>> macro( BuildProject PROJECT SOLUTION PROJECT_SOURCE INSTALL_RESULT ) >>>>> #... >>>>> add_custom_target( Build${PROJECT} ALL >>>>> COMMAND cmake -G "${CMAKE_GENERATOR}" ${PROJECT_SOURCE} >>>>> -DCMAKE_BUILD_TYPE=${CMAKE_BUILD_TYPE} >>>>> -DCMAKE_INSTALL_PREFIX=${INSTALL} ${ARGN} >>>>> COMMAND ${BUILD_COMMAND} >>>>> WORKING_DIRECTORY ${BUILD} >>>>> ${ADD_SOURCES} >>>>> ) >>>>> #... >>>>> endmacro() >>>>> >>>>> ADD_SOURCES is the .SLN filename >>>>> BUILD is where it's building >>>>> BUILD_COMMAND was retreived using build_command() >>>>> >>>>> and occasionally do ADD_CUSTOM_COMMAND( target Build${PROJECT} ... >>>>> some other commands... ) >>>>> >>>>> >>>>> on watcom, mingw, and usually visual studio, the cmake lists that uses >>>>> this macro basically ends up running cmake and an approprite build >>>>> command for each project... >>>>> >>>>> I have a bunch fo project build targets, and have added dependencies >>>>> to most of that like 'add_dependencies( ${LAST_TARGET} Buildcore )' >>>>> so Buildcore will get built first... last_target is set by the >>>>> macro... yadda yadda. >>>>> >>>>> All of that works. >>>>> >>>>> But today, and some time last month a bit... >>>> -- >>>> >>>> Powered by www.kitware.com >>>> >>>> Visit other Kitware open-source projects at >>>> http://www.kitware.com/opensource/opensource.html >>>> >>>> Please keep messages on-topic and check the CMake FAQ at: >>>> http://www.cmake.org/Wiki/CMake_FAQ >>>> >>>> Follow this link to subscribe/unsubscribe: >>>> http://public.kitware.com/cgi-bin/mailman/listinfo/cmake-developers --
Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the CMake FAQ at: http://www.cmake.org/Wiki/CMake_FAQ Follow this link to subscribe/unsubscribe: http://public.kitware.com/cgi-bin/mailman/listinfo/cmake-developers
