Rob, Bruno, have a look at the instructions here: http://www.jamestowndistributors.com/userportal/pdfs/Edson/EB355_689BrakeInstall.PDF
The material was ordered from mcmaster carr. I used the recommended black loctite. Can't now find the link or remember but I'm fairly certain I found the instructions on this list. More reading (including a link to the product page): https://www.mail-archive.com/cnc-list@cnc-list.com/msg20988.html Steve Suhana, C&C 32 Toronto On Sun, May 31, 2015 at 9:33 PM, Chuck S via CnC-List <cnc-list@cnc-list.com > wrote: > Edsonmarine.com now has videos on servicing their pedestals; removing the > brake and others. > > > Chuck > Resolute > 1990 C&C 34R > Broad Creek, Magothy River, Md > > ------------------------------ > *From: *"robert via CnC-List" <cnc-list@cnc-list.com> > *To: *cnc-list@cnc-list.com > *Cc: *"robert" <robertabb...@eastlink.ca>, "mike amirault" < > amira...@eastlink.ca> > *Sent: *Sunday, May 31, 2015 8:38:43 PM > *Subject: *Re: Stus-List Edson Pedestal > > I bought an Edson Brake Pad Repair Kit a few years back but have never had > the nerve to install it. The Dansforth compass slips out of the binnacle > easy enough, but after that, it gets a bit intimidating for me. > > What happens after the compass is removed? > > Rob Abbott > AZURA > C&C 32 - 84 > Halifax, N.S. > > On 2015-05-31 3:17 PM, Stevan Plavsa via CnC-List wrote: > > I have brake pad material left over from when I relined my wheel brake. > > I'll happily share the left overs with listers. I can send a piece big > enough to do both brake pads for the cost of shipping. Email me off list. > > Steve > Suhana, C&C 32 > Toronto > > > On Sat, May 30, 2015 at 9:48 AM, mike amirault via CnC-List < > cnc-list@cnc-list.com> wrote: > >> Well, it doesn't take an expert to install it. Anyone with a reasonable >> mechanical aptitude should be able to do this in less than an hour. >> However, if the knurling on the brass gear is badly worn, the new brake >> pads will not help much. >> Good luck. >> >> Mike Amirault >> C&C33 mkii "Lovely Cruise" >> St Margarets Bay, NS >> >> _______________________________________________ >> >> Email address: >> CnC-List@cnc-list.com >> To change your list preferences, including unsubscribing -- go to the >> bottom of page at: >> http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com >> >> >> > > > _______________________________________________ > > Email address:CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the bottom > of page at:http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > > > _______________________________________________ > > Email address: > CnC-List@cnc-list.com > To change your list preferences, including unsubscribing -- go to the > bottom of page at: > http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com > > >
_______________________________________________ Email address: CnC-List@cnc-list.com To change your list preferences, including unsubscribing -- go to the bottom of page at: http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com
