Ok so you can get the recommended miwalkee cordless drill doe under $300 and
the bit for $50. so for almost 1/2 the price you can do the same thing...
Seems like a really good alternative Danny
---------- Original Message ----------
From: Danny Haughey via CnC-List <cnc-list@cnc-list.com>
To: cnc-list@cnc-list.com
Cc: Danny Haughey <djhaug...@juno.com>
Subject: Re: Stus-List Winchrite
Date: Tue, 6 Oct 2015 15:19:55 GMT
I saw a video once where a guy was using a cordless dewalt right angle drill as
a winch rite. looked really cool! My new boat came with an electric winch on
the coach roof! The PO said if you do it right you can do almost any line with
it. Danny
---------- Original Message ----------
From: Jean-Francois J Rivard via CnC-List <cnc-list@cnc-list.com>
To: cnc-list@cnc-list.com
Cc: Jean-Francois J Rivard <jfriv...@us.ibm.com>
Subject: Stus-List Winchrite
Date: Tue, 6 Oct 2015 10:17:43 -0400
I agree with Chuck on the 'Self tacking" I read about that somewhere and we've
been doing it on the 2nd half of the racing season. Our technique is slightly
different but it's the same idea:
1- You start tacking without releasing the genoa. It will 'Catch" on the
opposite tack and spin the boat in a jiff.
2- As soon as the boat has turned about 25-30 degrees let the lazy sheet go and
grab the new sheet / pull it in (by hand) as fast as you can. (Slowing down
the turn with the wheel is a good idea, if you keep the wheel set for a tack
the boat will "Over-tack")
3- If you do it right (It's all timing) you'll need about 2 turns on the winch
to finish trimming. We actually counted the handle turns to demonstrate the
benefits of "staying ahead of task" as a little life lesson to my daughter
during a race a couple weekends ago ..
Works particularly well in light to moderate winds (Less than 15) it still
helps a bunch in higher winds.
That being said that Winchrite thing looks real good :-) I think $650.00 is a
reasonable price (If it works well) compared to several 1000.00's for electric
winches. I'd love to try one. My shoulders get do get sore when we race in
high winds...
-Francois Rivard
1990 34+ "Take Five"
Lake Lanier, GA
Subject: Re: Stus-List Winchrite
Message-ID:
<106579653.15511599.1444097037608.javamail.zim...@comcast.net>
Content-Type: text/plain; charset="utf-8"
Have you priced electric winches? You may need dedicated batteries for those,
too?
Self tailers are less money. Not sure about winch rites? Smaller jib for
shorthanded sailing may be wiser. Also, try to head upwind more during a tack
to get the sail sheeted in without the winch handle.
Remove any slack in lazy sheet before tacking and put two turns on the winch.
Set the mainsheet and traveller close to center to help the turn. Put the
autohelm on Standby and let the boat tack itself. Let the wheel ease into the
turn slowly, hold the release till the wind is 1/3 up the genoa, release and
start pulling the new sheet. Once the genoa clew is past the shrouds, try and
slow the turn with a nudge of the wheel, so the sail is inside the lifelines
and you can get 95% of the sheet in, without the handle, fall off to the right
course, set autohelm, trim the last bit of sheet. Takes practice, but can be a
lot of fun. Our boats turn so easily, you can handle them like a dinghy.
If you go in irons and find you are going backward, remember to "Reverse the
Rudder" to get pointed in the right direction. Don't let the rudder turn to the
stop. One or two spokes off center is all that you need to turn the boat and
get back on course.
Chuck
Resolute
1990 C&C 34R
Broad Creek, Magothy River, Md
_______________________________________________
Email address:
CnC-List@cnc-list.com
To change your list preferences, including unsubscribing -- go to the bottom of
page at:
http://cnc-list.com/mailman/listinfo/cnc-list_cnc-list.com