Milwaukee is the one I'm loosely familiar with. Josh
On Aug 10, 2016 10:40 AM, "Charlie Nelson via CnC-List" < cnc-list@cnc-list.com> wrote: > My rigger uses a portable right angle drill for hoisting him/crew up the > mast. He likes the Milwaukee brand for ~$300-400. He used it to remove my > roller furling recently with his crew hoisting him skyward with the drill > and a #30 Lewmar 2 spped ST winch. He was afraid the winch would no give > the drill the advantage it needed but it worked fine. > > FWIW, > > Charlie Nelson > Water Phantom > 1995 C&C 36 XL/kcb > Oriental, NC > > cenel...@aol.com > > > -----Original Message----- > From: Josh Muckley via CnC-List <cnc-list@cnc-list.com> > To: C&C List <cnc-list@cnc-list.com> > Cc: Josh Muckley <muckl...@gmail.com> > Sent: Wed, Aug 10, 2016 10:01 am > Subject: Re: Stus-List LED masthead lights - Now Winch-rite/24v drill > > Joel, > As for winch-rites I've heard people on cruisers forums talk about using a > 24v right angled drill. If actually costs the same or less than the > winch-rite AND you get a drill out of it too. I'll see if I can find more > info. > Josh Muckley > S/V Sea Hawk > 1989 C&C 37+ > Solomons, MD > > On Aug 10, 2016 9:53 AM, "Joel Aronson via CnC-List" < > cnc-list@cnc-list.com> wrote: > >> Josh, >> >> Thanks. I'll look for them. Admiral wants a Winch-Rite which they also >> sell. >> >> Joel >> >> On Tue, Aug 9, 2016 at 11:48 PM, Josh Muckley via CnC-List < >> cnc-list@cnc-list.com> wrote: >> >>> Following the link isn't exactly intuitive, but the boat show tent and >>> land locations are shown and then you have to go to the boat show map to >>> see where they are. >>> http://www.annapolisboatshows.com/united-states-sailboat-sho >>> w/plan-your-visit/show-layout/ >>> Josh >>> >>> On Aug 9, 2016 11:39 PM, "Josh Muckley" <muckl...@gmail.com> wrote: >>> >>>> Cruising Solutions is the exhibitor that sells marine beam products. >>>> You can compare prices on their website. Follow the link below for their >>>> 2016 boat show info and website. >>>> http://www.usboat.com/boat_show.cgi?exhibitor_id=443&boat_sh >>>> ow_type=usss >>>> Josh Muckley >>>> S/V Sea Hawk >>>> 1989 C&C 37+ >>>> Solomons, MD >>>> >>>> On Aug 9, 2016 4:43 PM, "Joel Aronson via CnC-List" < >>>> cnc-list@cnc-list.com> wrote: >>>> >>>>> Does not look like Marinebeam comes to the Annapolis show. I signed >>>>> up for their newsletter. Hopefully there will be promotions. >>>>> >>>>> Do the tricolor/anchor and steaming/deck lights require 3 strand wire >>>>> (2 hot, 1 ground)? >>>>> >>>>> Joel >>>>> >>>>> On Tue, Aug 9, 2016 at 4:14 PM, Bill Coleman via CnC-List < >>>>> cnc-list@cnc-list.com> wrote: >>>>> >>>>>> Now that you ask that, that is the one thing I didn’t like about the >>>>>> steaming light, there was very little space for wiring behind the >>>>>> lights. I >>>>>> cut out a little of the plastic to make more room. >>>>>> >>>>>> My wiring comes through the front there, and I have a tie wrap >>>>>> choking the cord, (it is a good grade SO Cord), and that has held for >>>>>> nearly 20 years, but a little more room would certainly been nice. >>>>>> >>>>>> Bill Coleman >>>>>> C&C 39 Erie, PA >>>>>> >>>>>> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf >>>>>> Of *Nauset Beach via CnC-List >>>>>> *Sent:* Tuesday, August 09, 2016 12:29 PM >>>>>> *To:* cnc-list@cnc-list.com >>>>>> *Cc:* Nauset Beach >>>>>> >>>>>> *Subject:* Re: Stus-List LED masthead lights and steaming/deck light >>>>>> >>>>>> Bill &/or Fred, >>>>>> >>>>>> The steaming / foredeck sounds like a great light and will probably >>>>>> get one. Have had 2 of the Forespar units and the foredeck light dies >>>>>> within a couple years. >>>>>> >>>>>> From one of the posted reviews it sounds like the electrical >>>>>> connection is made with butt connectors. Did either of you provide any >>>>>> strain relief on the wire or is the weight of the wire hanging on the 3 >>>>>> connections? >>>>>> >>>>>> Thanks, >>>>>> Brian >>>>>> >>>>>> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf >>>>>> Of *Bill Coleman via CnC-List >>>>>> *Sent:* Tuesday, August 09, 2016 12:04 PM >>>>>> *To:* cnc-list@cnc-list.com >>>>>> *Cc:* Bill Coleman <colt...@verizon.net> >>>>>> *Subject:* Re: Stus-List LED masthead lights and steaming/deck light >>>>>> >>>>>> I will vouch for the deck/steaming light, I got one this spring on >>>>>> Fred’s recommendation, and it is sweet! >>>>>> Seems to be sealed. Very bright. >>>>>> >>>>>> Bill Coleman >>>>>> C&C 39 Erie, PA[image: animated_favicon1] >>>>>> >>>>>> *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com >>>>>> <cnc-list-boun...@cnc-list.com>] *On Behalf Of *Frederick G Street >>>>>> via CnC-List >>>>>> *Sent:* Tuesday, August 09, 2016 9:37 AM >>>>>> *To:* cnc-list@cnc-list.com >>>>>> *Cc:* Frederick G Street >>>>>> *Subject:* Re: Stus-List LED masthead lights and steaming/deck light >>>>>> >>>>>> Joel — I replaced all my mast lighting this past winter with products >>>>>> from MarineBeam: >>>>>> >>>>>> http://marinebeam.com/led-tri-color-navigation-and-all-aroun >>>>>> d-anchor-light/ >>>>>> >>>>>> http://marinebeam.com/led-masthead-foredeck-combination-light/ >>>>>> >>>>>> I’m very pleased with the quality of the gear, and the installation >>>>>> went well. I pulled new 16AWG wire for everything to the bottom of the >>>>>> mast, then pulled a new common 12AWG ground from there to the panel, >>>>>> along >>>>>> with 16AWG runs for the hots. The new lights are far brighter than the >>>>>> old >>>>>> ones, and seem like they’ll do well in the weather. >>>>>> >>>>>> At the same time, I pulled new VHF and cell repeater antenna runs, >>>>>> and installed new antennas at the masthead; and I also installed an LED >>>>>> Windex light wired with my compass light switch. >>>>>> >>>>>> — Fred >>>>>> >>>>>> Fred Street -- Minneapolis >>>>>> S/V *Oceanis* (1979 C&C Landfall 38) -- Bayfield, WI >>>>>> >>>>>> >>>>>> On Aug 9, 2016, at 8:21 AM, Joel Aronson via CnC-List < >>>>>> cnc-list@cnc-list.com> wrote: >>>>>> >>>>>> It will be too hot in Annapolis for me this weekend, so I want to >>>>>> start on my boat show shopping list. I want to replace my anchor light >>>>>> with an LED anchor/Tri combo and replace the steaming light with a >>>>>> steaming/deck light. >>>>>> >>>>>> Any favorites? Any dogs to avoid? >>>>>> >>>>>> -- >>>>>> Joel >>>>>> 301 541 8551 >>>>>> _______________________________________________ >>>>>> >>>>>> This list is supported by the generous donations of our members. If >>>>>> you like what we do, please help us pay for our costs by donating. All >>>>>> Contributions are greatly appreciated! >>>>>> >>>>>> >>>>>> >>>>>> _______________________________________________ >>>>>> >>>>>> This list is supported by the generous donations of our members. If >>>>>> you like what we do, please help us pay for our costs by donating. All >>>>>> Contributions are greatly appreciated! >>>>>> >>>>>> >>>>> >>>>> >>>>> -- >>>>> Joel >>>>> 301 541 8551 >>>>> >>>>> _______________________________________________ >>>>> >>>>> This list is supported by the generous donations of our members. If >>>>> you like what we do, please help us pay for our costs by donating. All >>>>> Contributions are greatly appreciated! >>>>> >>>>> >>> _______________________________________________ >>> >>> This list is supported by the generous donations of our members. If you >>> like what we do, please help us pay for our costs by donating. All >>> Contributions are greatly appreciated! >>> >>> >> >> >> -- >> Joel >> 301 541 8551 >> >> _______________________________________________ >> >> This list is supported by the generous donations of our members. If you >> like what we do, please help us pay for our costs by donating. All >> Contributions are greatly appreciated! >> >> _______________________________________________ > > This list is supported by the generous donations of our members. If you > like what we do, please help us pay for our costs by donating. All > Contributions are greatly appreciated! > > _______________________________________________ > > This list is supported by the generous donations of our members. If you > like what we do, please help us pay for our costs by donating. All > Contributions are greatly appreciated! > >
_______________________________________________ This list is supported by the generous donations of our members. If you like what we do, please help us pay for our costs by donating. All Contributions are greatly appreciated!
