That’s exactly how the job should be done. On Sat, Jun 13, 2020 at 3:51 PM Rick Brass via CnC-List < cnc-list@cnc-list.com> wrote:
> To me "Topsides" is from the water line up to the toerail/gunnel - so it > is the sides and stern of the boat. Bottom paint goes on the bottom (which > in my case ends about an inch or so above the actual waterline). The deck > is the deck. > > My topside paint job included painting the stern, the cove strip, the C&C > stars & daggers, and the boot stripe (which is actually 3 stripes of > decreasing width from about 4" above the waterline) all painted in red > Alexseal. The rest of the hull was painted off white before the red > portions were added. Yes, they removed the hardware (essentially the bow > lights, stern lights, rear boarding step, and the boarding ladder and > reinstalled after the paint job. They also removed and replaced the decals > for the boat name and logos on each quarter and the hail port and yacht > club decals on the transom. I purchased the decals myself. > > Since someone asked about the deck, I had that repainted, too. > > I had a soft spot in the core of the cockpit aft of the helm. Probably > 12-14 square feet of core needed to be replaced. The outer skin was > removed, the old core removed, the inner skin raised back up to make the > deck surface level after the job was done, new core was installed (on my 38 > there was actually a layer of balsa and a layer of plywood that totaled at > least 3/4 inch thick), and the old skin was glassed back in place. Repair > of the soft spot became the driver for repainting the deck. > > We used off white Interdeck (Interdeck with non-skid additive on the > non-skid areas). The only hardware removed was the hand rails, the Nicro > power vents, and the hardware for the dodger. Windlass, winches, genoa > tracks, rope clutches, the base of the radar arch, radar pole, etc (da*n > there is a lot of deck hardware) were all masked and painted around. My > person attitude about removing the hardware is along the lines of "If the > core under the hardware is sound and there is no leak, why remove and rebed > the hardware - and risk a new leak - just to put pretty paint where no one > will ever see it?" I'd need to look up the cost of painting the deck, not > including the core repair in the cockpit, if anyone is interested. > > Rick Brass > > -----Original Message----- > From: "Della Barba, Joe via CnC-List" > Sent: Jun 12, 2020 8:24 AM > To: "cnc-list@cnc-list.com" > Cc: "Della Barba, Joe" > Subject: Re: Stus-List [EXTERNAL] Re: boat painting in Washington NC > > I am getting a bit confused. > > “Hull” to me means the waterline and up, not bottom paint. The deck is the > deck. “Topsides” is generic for anything that isn’t bottom paint. > > So is $125/ft. the hull, the deck, or both? > > Thanks! > > > > > > *Joe Della Barba Coquina C&C 35 MK I* > > *www.dellabarba.com <http://www.dellabarba.com>* > > > > > > > > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com] *On Behalf Of *John > Conklin via CnC-List > *Sent:* Thursday, June 11, 2020 11:49 PM > *To:* cnc-list@cnc-list.com > *Cc:* John Conklin <jconk...@hotmail.com> > *Subject:* [EXTERNAL] Re: Stus-List boat painting in Washington NC > > > > Rick mentioned topsides, did not see any mention of hull. I would sign up > tomorow for both @$125/ft ! Do they remove harware to? or just tape > everyting off ? > > John Conklin > > S/V Halcyon > > www.flirtingwithfire.net > <https://protect2.fireeye.com/v1/url?k=7f9d1366-230b42c3-7f9d3a11-0cc47adc5e34-2b38e1d9029ab39d&q=1&e=fe4f9a1b-0e19-441a-a9f0-8aa150d3eab3&u=http%3A%2F%2Fwww.flirtingwithfire.net%2F> > > > > > On Jun 11, 2020, at 11:25 PM, cscheaffer via CnC-List < > cnc-list@cnc-list.com> wrote: > > Is the price per foot including hull and deck? > > > > > > > > Sent from my Verizon, Samsung Galaxy smartphone > > > > > > -------- Original message -------- > > From: Rick Brass via CnC-List <cnc-list@cnc-list.com> > > Date: 6/11/20 10:24 PM (GMT-05:00) > > To: cnc-list@cnc-list.com > > Cc: Rick Brass <rickbr...@earthlink.net> > > Subject: Re: Stus-List boat painting in Washington NC > > > > Jim already jumped on your question. But, yes, I had the topsides painted > in 2017 by William and Beau (the company name is Washington Yacht Service, > but the phone number is the one below). We/they used Alexseal paint > (similar to Awlgrip but *much* less expensive). I’d need to check but I > think it cost $125 per foot. > > > > > > Rick Brass > > Washington, NC > > > > > > > > *From:* CnC-List [mailto:cnc-list-boun...@cnc-list.com > <cnc-list-boun...@cnc-list.com>] *On Behalf Of *detroito91 via CnC-List > *Sent:* Friday, June 5, 2020 1:43 PM > *To:* cnc-list@cnc-list.com > *Cc:* detroito91 <detroit...@aol.com> > *Subject:* Re: Stus-List boat painting in Washington NC > > > > I didn't quote any prices but I believe rick brass did. > > The person he was talking about was. William keener > > 919.395.8761 > > He does all of our work. Give him a call. Great to work with. > > I'll let him know you may be calling. > > > > Jim Schwartz > > SEA YA! > > 38 landfall > > Washington nc > > > > > > Sent from my Verizon, Samsung Galaxy smartphone > > > > > > -------- Original message -------- > > From: "Della Barba, Joe via CnC-List" <cnc-list@cnc-list.com> > > Date: 6/5/20 12:57 PM (GMT-05:00) > > To: cnc-list@cnc-list.com > > Cc: "Della Barba, Joe" <joe.della.ba...@ssa.gov> > > Subject: Stus-List boat painting in Washington NC > > > > Some time ago someone posted the price to get a boat painted in NC that > was WAY under anything around here. > > Does anyone recall the name of the yard that does this? > > > > > > *Joe Della Barba Coquina C&C 35 MK I* > > *www.dellabarba.com > <https://protect2.fireeye.com/v1/url?k=4ed9e190-124fb035-4ed9c8e7-0cc47adc5e34-6178dd5b533db808&q=1&e=fe4f9a1b-0e19-441a-a9f0-8aa150d3eab3&u=http%3A%2F%2Fwww.dellabarba.com%2F>* > > > > > > > > _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > > > > > > > _______________________________________________ > > Thanks everyone for supporting this list with your contributions. Each > and every one is greatly appreciated. If you want to support the list - > use PayPal to send contribution -- https://www.paypal.me/stumurray > > -- Sent from Gmail Mobile
_______________________________________________ Thanks everyone for supporting this list with your contributions. Each and every one is greatly appreciated. If you want to support the list - use PayPal to send contribution -- https://www.paypal.me/stumurray
