This is an automated email from the ASF dual-hosted git repository.
xiaoxiang pushed a commit to branch master
in repository https://gitbox.apache.org/repos/asf/nuttx.git
The following commit(s) were added to refs/heads/master by this push:
new 6633f9d907 boards/arm/nucleo-f429zi: Add example trace
6633f9d907 is described below
commit 6633f9d907c3d88b0a9d98f414408a38b8f84071
Author: William Yang <[email protected]>
AuthorDate: Wed May 14 20:00:55 2025 +0800
boards/arm/nucleo-f429zi: Add example trace
Add example trace for board nucleo-f429zi
Signed-off-by: yangwei-x <[email protected]>
---
.../arm/stm32f4/boards/nucleo-f429zi/index.rst | 210 +++++++++++++++++++++
.../stm32/nucleo-f429zi/configs/trace/defconfig | 90 +++++++++
2 files changed, 300 insertions(+)
diff --git a/Documentation/platforms/arm/stm32f4/boards/nucleo-f429zi/index.rst
b/Documentation/platforms/arm/stm32f4/boards/nucleo-f429zi/index.rst
index 9aac7d1b7d..6cd589ae3e 100644
--- a/Documentation/platforms/arm/stm32f4/boards/nucleo-f429zi/index.rst
+++ b/Documentation/platforms/arm/stm32f4/boards/nucleo-f429zi/index.rst
@@ -5,3 +5,213 @@ ST Nucleo F429ZI
.. tags:: chip:stm32, chip:stm32f4, chip:stm32f429
The Nucleo F429ZI is a member of the Nucleo-144 board family.
+
+This page discusses issues unique to NuttX configurations for the ST
+Nucleo F429ZI board from ST Micro. See
+
+ http://www.st.com/en/evaluation-tools/nucleo-f429zi.html
+
+NucleoF429ZI:
+
+- Microprocessor: 32-bit ARM Cortex M4 with 180 MHz max CPU frequency
+- Memory: 2 MB Flash and 256+4 KB SRAM including 64-Kbyte of core coupled
memory
+- ADC: 3x12-bit ADC with 24 channels
+- DMA: 16-stream DMA controller with FIFOs and burst support
+- Timers: Up to 17 timers: up to 12 16-bit, 2 32-bit timers, two
+ watchdog timers, and a SysTick timer
+- GPIO: Up to 168 I/O ports with interrupt capability
+- I2C: Up to 3 I2C interfaces
+- USARTs: Up to 4 USARTs
+- SPIs: Up to 6 SPIs (45 Mbit/s)
+
+
+See:
+ https://www.st.com/en/microcontrollers-microprocessors/stm32f429zi.html
+
+
+Hardware
+========
+
+Buttons
+-------
+
+B1 USER: the user button is connected to the I/O PC13 (pin 2) of the STM32
+microcontroller.
+
+LEDs
+----
+
+The Nucleo F410RB provide a single user LED, LD2. LD2
+is the green LED connected to Arduino signal D13 corresponding to MCU I/O
+PA5 (pin 21) or PB13 (pin 34) depending on the STM32target.
+
+- When the I/O is HIGH value, the LED is on.
+- When the I/O is LOW, the LED is off.
+
+These LEDs are not used by the board port unless CONFIG_ARCH_LEDS is
+defined. In that case, the usage by the board port is defined in
+include/board.h and src/sam_leds.c. The LEDs are used to encode OS-related
+events as follows when the red LED (PE24) is available::
+
+ SYMBOL Meaning LD2
+ ------------------- ----------------------- -----------
+ LED_STARTED NuttX has been started OFF
+ LED_HEAPALLOCATE Heap has been allocated OFF
+ LED_IRQSENABLED Interrupts enabled OFF
+ LED_STACKCREATED Idle stack created ON
+ LED_INIRQ In an interrupt No change
+ LED_SIGNAL In a signal handler No change
+ LED_ASSERTION An assertion failed No change
+ LED_PANIC The system has crashed Blinking
+ LED_IDLE MCU is is sleep mode Not used
+
+Thus if LD2, NuttX has successfully booted and is, apparently, running
+normally. If LD2 is flashing at approximately 2Hz, then a fatal error
+has been detected and the system has halted.
+
+Serial Consoles
+===============
+
+USART1
+------
+
+Pins and Connectors::
+
+ RXD: PA11 CN10 pin 14
+ PB7 CN7 pin 21
+ TXD: PA10 CN9 pin 3, CN10 pin 33
+ PB6 CN5 pin 3, CN10 pin 17
+
+ NOTE: You may need to edit the include/board.h to select different USART1
+ pin selections.
+
+TTL to RS-232 converter connection::
+
+ Nucleo CN10 STM32F429ZI
+ ----------- ------------
+ Pin 21 PA9 USART1_RX *Warning you make need to reverse RX/TX on
+ Pin 33 PA10 USART1_TX some RS-232 converters
+ Pin 20 GND
+ Pin 8 U5V
+
+To configure USART1 as the console::
+
+ CONFIG_STM32_USART1=y
+ CONFIG_USART1_SERIALDRIVER=y
+ CONFIG_USART1_SERIAL_CONSOLE=y
+ CONFIG_USART1_RXBUFSIZE=256
+ CONFIG_USART1_TXBUFSIZE=256
+ CONFIG_USART1_BAUD=115200
+ CONFIG_USART1_BITS=8
+ CONFIG_USART1_PARITY=0
+ CONFIG_USART1_2STOP=0
+
+USART2
+------
+
+Pins and Connectors::
+
+ RXD: PA3 CN9 pin 1 (See SB13, 14, 62, 63). CN10 pin 37
+ PD6
+ TXD: PA2 CN9 pin 2(See SB13, 14, 62, 63). CN10 pin 35
+ PD5
+
+ UART2 is the default in all of these configurations.
+
+TTL to RS-232 converter connection::
+
+ Nucleo CN9 STM32F429ZI
+ ----------- ------------
+ Pin 1 PA3 USART2_RX *Warning you make need to reverse RX/TX on
+ Pin 2 PA2 USART2_TX some RS-232 converters
+
+Solder Bridges. This configuration requires:
+
+- SB62 and SB63 Closed: PA2 and PA3 on STM32 MCU are connected to D1 and D0
+ (pin 7 and pin 8) on Arduino connector CN9 and ST Morpho connector CN10
+ as USART signals. Thus SB13 and SB14 should be OFF.
+
+- SB13 and SB14 Open: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are
+ disconnected to PA3 and PA2 on STM32 MCU.
+
+To configure USART2 as the console::
+
+ CONFIG_STM32_USART2=y
+ CONFIG_USART2_SERIALDRIVER=y
+ CONFIG_USART2_SERIAL_CONSOLE=y
+ CONFIG_USART2_RXBUFSIZE=256
+ CONFIG_USART2_TXBUFSIZE=256
+ CONFIG_USART2_BAUD=115200
+ CONFIG_USART2_BITS=8
+ CONFIG_USART2_PARITY=0
+ CONFIG_USART2_2STOP=0
+
+USART6
+------
+
+Pins and Connectors::
+
+ RXD: PC7 CN5 pin2, CN10 pin 19
+ PA12 CN10, pin 12
+ TXD: PC6 CN10, pin 4
+ PA11 CN10, pin 14
+
+To configure USART6 as the console::
+
+ CONFIG_STM32_USART6=y
+ CONFIG_USART6_SERIALDRIVER=y
+ CONFIG_USART6_SERIAL_CONSOLE=y
+ CONFIG_USART6_RXBUFSIZE=256
+ CONFIG_USART6_TXBUFSIZE=256
+ CONFIG_USART6_BAUD=115200
+ CONFIG_USART6_BITS=8
+ CONFIG_USART6_PARITY=0
+ CONFIG_USART6_2STOP=0
+
+Virtual COM Port
+----------------
+
+Yet another option is to use UART2 and the USB virtual COM port. This
+option may be more convenient for long term development, but is painful
+to use during board bring-up.
+
+Solder Bridges. This configuration requires:
+
+- SB62 and SB63 Open: PA2 and PA3 on STM32 MCU are disconnected to D1
+ and D0 (pin 7 and pin 8) on Arduino connector CN9 and ST Morpho
+ connector CN10.
+
+- SB13 and SB14 Closed: PA2 and PA3 on STM32F103C8T6 (ST-LINK MCU) are
+ connected to PA3 and PA2 on STM32 MCU to have USART communication
+ between them. Thus SB61, SB62 and SB63 should be OFF.
+
+Configuring USART2 is the same as given above.
+
+Question: What BAUD should be configure to interface with the Virtual
+COM port? 115200 8N1?
+
+Default:
+As shipped, SB62 and SB63 are open and SB13 and SB14 closed, so the
+virtual COM port is enabled.
+
+Configurations
+==============
+
+trace
+---
+
+Configures the trace located at apps/system/trace for the
+Nucleo-F429ZI board. The Configuration enables the serial interfaces
+on UART2. Support for builtin applications is enabled, and selected
+application trace.
+
+NOTES:
+
+1. This configuration uses the mconf-based configuration tool. To
+ change this configuration using that tool, you should:
+
+ a. Build and install the kconfig-mconf tool. See nuttx/README.txt
+ see additional README.txt files in the NuttX tools repository.
+
+ b. Execute 'make menuconfig' in nuttx/ in order to start the
+ reconfiguration process.
diff --git a/boards/arm/stm32/nucleo-f429zi/configs/trace/defconfig
b/boards/arm/stm32/nucleo-f429zi/configs/trace/defconfig
new file mode 100644
index 0000000000..3e373893ad
--- /dev/null
+++ b/boards/arm/stm32/nucleo-f429zi/configs/trace/defconfig
@@ -0,0 +1,90 @@
+#
+# This file is autogenerated: PLEASE DO NOT EDIT IT.
+#
+# You can use "make menuconfig" to make any modifications to the installed
.config file.
+# You can then do "make savedefconfig" to generate a new defconfig file that
includes your
+# modifications.
+#
+# CONFIG_ARCH_FPU is not set
+# CONFIG_STM32_FLASH_PREFETCH is not set
+# CONFIG_STM32_USE_LEGACY_PINMAP is not set
+CONFIG_ARCH="arm"
+CONFIG_ARCH_BOARD="nucleo-f429zi"
+CONFIG_ARCH_BOARD_NUCLEO_F429ZI=y
+CONFIG_ARCH_BUTTONS=y
+CONFIG_ARCH_CHIP="stm32"
+CONFIG_ARCH_CHIP_STM32=y
+CONFIG_ARCH_CHIP_STM32F429Z=y
+CONFIG_ARCH_STACKDUMP=y
+CONFIG_BOARD_LOOPSPERMSEC=16717
+CONFIG_BUILTIN=y
+CONFIG_DEBUG_SYMBOLS=y
+CONFIG_DRIVERS_NOTE=y
+CONFIG_DRIVERS_NOTECTL=y
+CONFIG_ETH0_PHY_LAN8742A=y
+CONFIG_FS_PROCFS=y
+CONFIG_FS_PROCFS_REGISTER=y
+CONFIG_FS_TMPFS=y
+CONFIG_HAVE_CXX=y
+CONFIG_HAVE_CXXINITIALIZE=y
+CONFIG_INIT_ENTRYPOINT="nsh_main"
+CONFIG_INTELHEX_BINARY=y
+CONFIG_LINE_MAX=64
+CONFIG_MM_REGIONS=2
+CONFIG_NET=y
+CONFIG_NETDB_DNSCLIENT=y
+CONFIG_NETINIT_DHCPC=y
+CONFIG_NETINIT_NOMAC=y
+CONFIG_NETUTILS_DISCOVER=y
+CONFIG_NETUTILS_TELNETD=y
+CONFIG_NETUTILS_WEBCLIENT=y
+CONFIG_NET_ARP_IPIN=y
+CONFIG_NET_BROADCAST=y
+CONFIG_NET_ETH_PKTSIZE=1500
+CONFIG_NET_ICMP_SOCKET=y
+CONFIG_NET_IGMP=y
+CONFIG_NET_LOOPBACK=y
+CONFIG_NET_ROUTE=y
+CONFIG_NET_STATISTICS=y
+CONFIG_NET_TCP=y
+CONFIG_NET_UDP=y
+CONFIG_NET_UDP_CHECKSUMS=y
+CONFIG_NSH_BUILTIN_APPS=y
+CONFIG_NSH_FILEIOSIZE=512
+CONFIG_NSH_READLINE=y
+CONFIG_NUCLEO_F429ZI_CONSOLE_VIRTUAL=y
+CONFIG_PREALLOC_TIMERS=4
+CONFIG_RAM_SIZE=114688
+CONFIG_RAM_START=0x20000000
+CONFIG_RAW_BINARY=y
+CONFIG_RR_INTERVAL=200
+CONFIG_SCHED_HPWORK=y
+CONFIG_SCHED_INSTRUMENTATION=y
+CONFIG_SCHED_INSTRUMENTATION_DUMP=y
+CONFIG_SCHED_INSTRUMENTATION_FILTER=y
+CONFIG_SCHED_LPWORK=y
+CONFIG_SCHED_WAITPID=y
+CONFIG_SPI=y
+CONFIG_STACK_USAGE=y
+CONFIG_START_DAY=6
+CONFIG_START_MONTH=12
+CONFIG_START_YEAR=2011
+CONFIG_STM32_DISABLE_IDLE_SLEEP_DURING_DEBUG=y
+CONFIG_STM32_ETHMAC=y
+CONFIG_STM32_FLASH_CONFIG_I=y
+CONFIG_STM32_PHYADDR=0
+CONFIG_STM32_PHYSR=31
+CONFIG_STM32_PHYSR_100FD=0x0018
+CONFIG_STM32_PHYSR_100HD=0x0008
+CONFIG_STM32_PHYSR_10FD=0x0014
+CONFIG_STM32_PHYSR_10HD=0x0004
+CONFIG_STM32_PHYSR_ALTCONFIG=y
+CONFIG_STM32_PHYSR_ALTMODE=0x001c
+CONFIG_STM32_RMII_EXTCLK=y
+CONFIG_SYSTEM_DHCPC_RENEW=y
+CONFIG_SYSTEM_NSH=y
+CONFIG_SYSTEM_PING=y
+CONFIG_SYSTEM_TRACE=y
+CONFIG_SYSTEM_TRACE_STACKSIZE=8192
+CONFIG_TASK_NAME_SIZE=32
+CONFIG_USART3_SERIAL_CONSOLE=y
