Ok, I switched to wpa. I had to change the key anyway (If you watch the iwconfig output I posted, you can see my wep-key :P ).
Peter Op Friday 25 July 2008 00:06:38 schreef Evan: > "wep_key0=<I'm not showing that!>" > > its wep, therefore obsolete. if anyone lives near you and wants to know > your key, they will take the 10 minutes or less that it takes to crack any > wep key. consider wpa > > > Jim Morris wrote: > Make sure you do ifdown usb0 before ifup eth0 > > Then if dhcp does not get a lease first time through (which for me is about > 50/50) then you can do this from the console which always gets the lease > for me. > > > udhcpc eth0 > > After that wifi should work. > > Peter Nijs wrote: > > After a whole lot of tweaking I still cannot get an IP from my wireless > router. My current setup looks like this: > > /etc/network/interfaces:--------------------------- > # /etc/network/interfaces -- configuration file for ifup(8), ifdown(8) > > # The loopback interface > auto lo > iface lo inet loopback > > # Wireless interfaces > iface wlan0 inet dhcp > wireless_mode managed > wireless_essid any > iface atml0 inet dhcp > > # Wired or wireless interfaces > iface eth0 inet dhcp > wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf > > iface eth1 inet dhcp > > # Ethernet/RNDIS gadget (g_ether) > # ... or on host side, usbnet and random hwaddr > auto usb0 > iface usb0 inet static > address 192.168.0.202 > netmask 255.255.255.0 > network 192.168.0.0 > gateway 192.168.0.200 > up echo nameserver 192.168.0.200 >/etc/resolv.conf > > # Bluetooth networking > iface bnep0 inet dhcp > > > /etc/wpa_supplicant/wpa_supplicant:---------------------------------------- >------ ctrl_interface=/var/run/wpa_supplicant > ctrl_interface_group=0 > eapol_version=1 > ap_scan=1 > fast_reauth=0 > > network={ > ssid="PN" > scan_ssid=1 > key_mgmt=NONE > wep_tx_keyidx=0 > > wep_key0=<I'm not showing that!> > priority=8 > } > > > Now here's what I do:-------------------------------------------- > [EMAIL PROTECTED]:~# ifup eth0 > sed: unrecognized option `--quiet' > BusyBox v1.11.1 (2008-07-18 00:49:01 CEST) multi-call binary > > Usage: sed [-efinr] pattern [files...] > > WPA: Configuring Interface > ioctl[SIOCSIWENCODEEXT]: Operation not supported > ioctl[SIOCSIWENCODEEXT]: Operation not supported > ioctl[SIOCSIWENCODEEXT]: Operation not supported > ioctl[SIOCSIWENCODEEXT]: Operation not supported > udhcpc (v1.11.1) started > run-parts: /etc/udhcpc.d/00avahi-autoipd exited with code 1 > Sending discover... > Sending discover... > Sending discover... > No lease, failing > [EMAIL PROTECTED]:~# iwconfig > lo no wireless extensions. > > usb0 no wireless extensions. > > eth0 AR6000 802.11g ESSID:"PN" > Mode:Managed Frequency:2.462 GHz Access Point: > 00:0E:2E:BA:1E:51 Bit Rate=36 Mb/s Tx-Power=15 dBm Sensitivity=0/3 > Retry:on > Encryption key:897B-9067-4C99-1AC7-B433-AABB-01 Security > mode:open Power Management:off > Link Quality:180/94 Signal level:-171 dBm Noise level:-96 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:7 Invalid misc:0 Missed beacon:1 > > [EMAIL PROTECTED]:~# ifconfig eth0 > eth0 Link encap:Ethernet HWaddr 00:12:CF:8E:E6:8D > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:646 errors:0 dropped:0 overruns:0 frame:0 > TX packets:419 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:278955 (272.4 KiB) TX bytes:20950 (20.4 KiB) > > [EMAIL PROTECTED]:~# > > While udhcpc is sending discovers I can see my router is leasing my neo a > valid ip for 60 seconds each "sending discover". > > Sometimes, in very rare cases I can get a decent lease. But that is not > reproducible. I think it's happened three times to me the last three days. > > Anyone knows how I could get an IP reliably? > > Peter Nijs > > Op Sunday 13 July 2008 01:05:12 schreef Jim Morris: > > arne anka wrote: > > well, i did what > http://wiki.openmoko.org/wiki/GTA02_wlan > says -- adding > > iface eth0 inet dhcp > wpa-conf /etc/wpa_supplicant/wpa_supplicant.conf > > Ok that worked, although I have some routing issues now. The manual method > did not work though. > > > iwconfig > > eth0 AR6000 802.11g ESSID:"morrisnetwork2" > Mode:Managed Frequency:2.422 GHz Access Point: > 00:1D:5A:BB:FA:A9 Bit Rate=48 Mb/s Tx-Power=16 dBm Sensitivity=0/3 > Retry:on > Encryption key:off > Power Management:off > Link Quality:207/94 Signal level:-144 dBm Noise level:-96 dBm > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:17 Invalid misc:0 Missed beacon:11 > > Although it says encryption key off, but I presume wpa_supplicant is > handling that. > > > ifconfig > > eth0 Link encap:Ethernet HWaddr 00:12:CF:74:20:A8 > inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 > TX packets:832 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:725595 (708.5 KiB) TX bytes:37892 (37.0 KiB) > > > So its connected to my access point, and I turned off eth0, but I cannot > ping the wireless, I'll work on that it may be routing or it may be > encryption. > > Thanks all. > > > ------------------------------------------------------------------------ > > _______________________________________________ > Openmoko community mailing list > community@lists.openmoko.org > http://lists.openmoko.org/mailman/listinfo/community
signature.asc
Description: This is a digitally signed message part.
_______________________________________________ Openmoko community mailing list community@lists.openmoko.org http://lists.openmoko.org/mailman/listinfo/community