Hi Lally, Here are some notes I took when configuring the USB networking, it's not really different from the wiki page.
It's working great on my macbook ( and with image 2008.8), it might help you: * Install AJZaurusUSB driver on mac: http://www.dsitri.de/wiki.php?page=AJZaurusUSB * After reboot, configure USB networking in Network pref panel: IP-V4: manual IP-Addr: 192.168.0.200 (you can use anything in 192.168.0.* but OM is configured by default to use 192.168.0.200 as the external gateway) Subnet: 255.255.255.0 (should be the default - see tip below if have issue with these settings) Router: 192.168.0.202 (not actually needed, OS X can figure this out for itself, unless you have other conflicting configurations) * Connect openmoko and: ssh [EMAIL PROTECTED] * hotplug problem, disconnected network -> change usb port, reboot computer * Some crash on the mac if you boot/shutdown with the usb plugged Alex El 12/09/2008, a las 0:25, Lally Singh escribió: > Hey all, > > Just got the FR yesterday (nice physical design). I installed the > patched network driver listed under "Apple CDC Ethernet driver > 10.5.x," and the Networking pane shows a USB serial connection, but no > ethernet. It also does not show up as enXX in ifconfig. > > This is OS X 10.5.4. I can use dfu-util fine. But, I haven't found > a way to get the wifi working yet, so the device is networkless. > > Anyone else have a mac with a working usb networking setup? What'd > you do? I'll happily update the wiki with the result. > > Here's my ifconfig when the device is plugged in (this was right > before I did the dfu-util reflash): > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 > inet 127.0.0.1 netmask 0xff000000 > inet6 ::1 prefixlen 128 > inet6 fd5d:a24b:2849:fed7:217:f2ff:fece:65ba prefixlen 128 > gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280 > stf0: flags=0<> mtu 1280 > en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > ether 00:17:f2:ce:65:ba > media: autoselect status: inactive > supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP > <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP > <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX > <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX > <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT > <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none > fw0: flags=8822<BROADCAST,SMART,SIMPLEX,MULTICAST> mtu 2030 > lladdr 00:19:e3:ff:fe:22:6b:5c > media: autoselect <full-duplex> status: inactive > supported media: autoselect <full-duplex> > en1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500 > inet6 fe80::219:e3ff:fe04:85c2%en1 prefixlen 64 scopeid 0x6 > inet 10.0.1.2 netmask 0xffffff00 broadcast 10.0.1.255 > ether 00:19:e3:04:85:c2 > media: autoselect status: active > supported media: autoselect > vmnet8: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu > 1500 > inet 172.16.1.1 netmask 0xffffff00 broadcast 172.16.1.255 > ether 00:50:56:c0:00:08 > vmnet1: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu > 1500 > inet 172.16.74.1 netmask 0xffffff00 broadcast 172.16.74.255 > ether 00:50:56:c0:00:01 > > Thanks in advance! > > -ls > > -- > H. Lally Singh > Ph.D. Candidate, Computer Science > Virginia Tech > > _______________________________________________ > Openmoko community mailing list > community@lists.openmoko.org > http://lists.openmoko.org/mailman/listinfo/community _______________________________________________ Openmoko community mailing list community@lists.openmoko.org http://lists.openmoko.org/mailman/listinfo/community