Bonjour,
Ma carte réseau ne veut tout simplement pas marcher sous Linux. Elle
est pourtant détectée par Linux, il réussit même à trouver le bon driver!
Mais, il est impossible de la mettre UP... C'est une D-Link DFE-530T (ou
tx, entk pas t+ ou tx+... )
Voici quelques logs qui pourrait vous aider à m'aider...
Tout d'abord, quelques commandes que j'ai exécuteés:
[root@local init.d]# ifconfig
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
Paquets Reçus:0 erreurs:0 jetés:0 débordements:0 trames:0
Paquets transmis:0 erreurs:0 jetés:0 débordements:0 carrier:0
collisions:0 lg file transmission:0
[root@local init.d]# ./network stop
Shutting down interface eth0 [ OK ]
[root@local init.d]# ./network start
Setting network parameters [ OK ]
Bringing up interface lo [ OK ]
Bringing up interface eth0 [ OK ]
[root@local init.d]# ifconfig
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
Paquets Reçus:0 erreurs:0 jetés:0 débordements:0 trames:0
Paquets transmis:0 erreurs:0 jetés:0 débordements:0 carrier:0
collisions:0 lg file transmission:0
[root@local init.d]# ifconfig eth0
eth0: erreur lors de la recherche d'infos sur l'interface: Périphérique non
trouvé
[root@local init.d]# ./network reload eth0
Bringing up device eth0 [ OK ]
[root@local init.d]# ./network status
Configured devices:
lo eth0
Devices that are down:
eth0
Devices with modified configuration:
[root@local init.d]#
Ensuite, mon dmesg:
Linux version 2.2.15-4mdk ([EMAIL PROTECTED]) (gcc version
2.95.3 19
991030 (prerelease)) #1 Wed May 10 15:31:30 CEST 2000
Detected 807200413 Hz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1612.19 BogoMIPS
Memory: 62768k/65408k available (1208k kernel code, 416k reserved, 944k
data, 72
k init, 0k bigmem)
Dentry hash table entries: 8192 (order 4, 64k)
Buffer cache hash table entries: 65536 (order 6, 256k)
Page cache hash table entries: 16384 (order 4, 64k)
VFS: Diskquotas version dquot_6.4.0 initialized
CPU: L1 I Cache: 64K L1 D Cache: 64K
CPU: L2 Cache: 1K
CPU: AMD AMD Athlon(tm) Processor stepping 00
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.35a (19990819) Richard Gooch ([EMAIL PROTECTED])
PCI: PCI BIOS revision 2.10 entry at 0xf10f0
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
TCP: Hash tables configured (ehash 65536 bhash 65536)
Initializing RT netlink socket
Starting kswapd v 1.5
Detected PS/2 Mouse Port.
Serial driver version 4.27 with MANY_PORTS MULTIPORT SHARE_IRQ enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.12)
Real Time Clock Driver v1.09
RAM disk driver initialized: 16 RAM disks of 4096K size
Uniform Multi-Platform E-IDE driver Revision: 6.30
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
VP_IDE: not 100% native mode: will probe irqs later
Split FIFO Configuration: 8 Primary buffers, threshold = 1/2
8 Second. buffers, threshold = 1/2
ide0: BM-DMA at 0xd800-0xd807, BIOS settings: hda:DMA, hdb:pio
ide0: VIA Bus-Master (U)DMA Timing Config Success
ide1: BM-DMA at 0xd808-0xd80f, BIOS settings: hdc:pio, hdd:DMA
ide1: VIA Bus-Master (U)DMA Timing Config Success
hda: Maxtor 91536U2, ATA DISK drive
hdd: MATSHITA CR-594, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: Maxtor 91536U2, 14655MB w/2048kB Cache, CHS=1868/255/63
hdd: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.56
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.90.0 MAX_MD_DEVS=256, MAX_REAL=12
raid5: measuring checksumming speed
raid5: MMX detected, trying high-speed MMX checksum routines
pII_mmx : 1871.853 MB/sec
p5_mmx : 2351.532 MB/sec
8regs : 1146.810 MB/sec
32regs : 939.927 MB/sec
using fastest function: p5_mmx (2351.532 MB/sec)
scsi : 0 hosts.
scsi : detected total.
md.c: sizeof(mdp_super_t) = 4096
Partition check:
hda: hda1 hda2 < hda5 hda6 >
autodetecting RAID arrays
autorun ...
... autorun DONE.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 72k freed
Adding Swap: 128484k swap-space (priority -1)
usb.c: registered new driver hub
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
usb.c: registered new driver keyboard
IrDA (tm) Protocols for Linux-2.2 (Dag Brattli)
usb-uhci.c: $Revision: 1.228 $ time 15:46:55 May 10 2000
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
usb.c: USB new device connect, assigned device number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: USB new device connect, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
hub.c: already running port 2 disabled by hub (EMI?), re-enabl
usb.c: USB disconnect on device 2
usb.c: USB new device connect, assigned device number 2
hub.c: USB hub found
hub.c: 4 ports detected
cat uses obsolete /proc/pci interface
mtrr: no MTRR for d8000000,400000 found
mtrr: no MTRR for d8000000,2000000 found
mtrr: no MTRR for d8000000,400000 found
cdrom: open failed.
end_request: I/O error, dev 02:00 (floppy), sector 0
OSS warning: Application caused too many output underrun error
#0.
Maintenant /proc/ioports:
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0330-0333 : MPU-401 UART
0376-0376 : ide1
03c0-03df : vga+
03f6-03f6 : ide0
03f8-03ff : serial(auto)
9800-980f : Avance Logic ALS4000
d000-d013 : usb-uhci
d400-d413 : usb-uhci
d800-d807 : ide0
d808-d80f : ide1
Pour finir avec /proc/interrupts:
CPU0
0: 395571 XT-PIC timer
1: 9441 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 26 XT-PIC usb-uhci, usb-uhci
8: 1 XT-PIC rtc
9: 0 XT-PIC MPU-401 UART
10: 147779 XT-PIC Avance Logic ALS4000
11: 309129 XT-PIC nvidia
12: 272317 XT-PIC PS/2 Mouse
13: 1 XT-PIC fpu
14: 55180 XT-PIC ide0
15: 79 XT-PIC ide1
NMI: 0
À noter que ma carte réseau utilise la plage 0xa000-0xa001 et l'IRQ 3.
Ah! et le driver est: via-rhine.
Merci de votre aide,
Laurent Mathieu
