Well I burned the beta iso's and this is how it turned out on a Abit
kt7-raid mb with 256m and an IBM udma100 DeskStar 30g drive. Using Asus
7100 GeForce2 MX 32m vid card. SCSI card aha-1505.
The install acted much like 7.2. I did notice on the partitioning that
not all the directories were listed on the drop down menu. Seems to me
that in 7.2 I could pick /boot.
This install was done using expert .......
Previously with 7.2 the scsi card worked on problem during the install
setting it with aha=0x140,9,7,1. I did the same and it said it was
located. However, when I booted up it was not present. See demg.txt
... said I had a conflict but this was not so before.
When I run DrakConf and then exit the loose the screen and am left with
a nice mouse pointer. Must do ctrl-alt-backspace. Same for both root
and user.
Tried deleting a user but errored with a ptmp error.
Sawfish or is it Sawmill, can't remembe what the new name is, was
installed but fails to run. It seems to start loading but then just
sits there.
Gnome does run.
My RTL-8139 card works fine and nothing had to be changed.
Not a big fan a watching only 3 images during the install. Made the
install seem longer than watching each individual file go by.
Noticed as well that the recpients line in netscape email is always
blank ... can't type anything.
Greg
Linux version 2.4.2-3mdk ([EMAIL PROTECTED]) (gcc version egcs-2.91.66
19990314/Linux (egcs-1.1.2 release)) #1 Tue Feb 27 02:14:17 CET 2001
BIOS-provided physical RAM map:
BIOS-e820: 000000000009fc00 @ 0000000000000000 (usable)
BIOS-e820: 0000000000000400 @ 000000000009fc00 (reserved)
BIOS-e820: 0000000000010000 @ 00000000000f0000 (reserved)
BIOS-e820: 0000000000010000 @ 00000000ffff0000 (reserved)
BIOS-e820: 000000000fef0000 @ 0000000000100000 (usable)
BIOS-e820: 000000000000d000 @ 000000000fff3000 (ACPI data)
BIOS-e820: 0000000000003000 @ 000000000fff0000 (ACPI NVS)
On node 0 totalpages: 65520
zone(0): 4096 pages.
zone(1): 61424 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/hde7 vga=788
Initializing CPU#0
Detected 800.032 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1595.80 BogoMIPS
Memory: 253992k/262080k available (956k kernel code, 7700k reserved, 387k data, 224k
init, 0k highmem)
Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
VFS: Diskquotas version dquot_6.5.0 initialized
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 02
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.37 (20001109) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfb430, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:07.0
isapnp: Scanning for PnP cards...
isapnp: Card 'Adaptec AVA-1505A'
isapnp: 1 Plug & Play card detected total
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.14)
Starting kswapd v1.8
vesafb: framebuffer at 0xd8000000, mapped to 0xd0800000, size 32768k
vesafb: mode is 800x600x16, linelength=1600, pages=3
vesafb: protected mode interface info at c000:0ed1
vesafb: scrolling: redraw
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
block: queued sectors max/low 168712kB/56237kB, 512 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 39
VP_IDE: chipset revision 16
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686a (rev 22) IDE UDMA66 controller on pci00:07.1
ide0: BM-DMA at 0xc000-0xc007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xc008-0xc00f, BIOS settings: hdc:pio, hdd:pio
HPT370: IDE controller on PCI bus 00 dev 98
PCI: Found IRQ 11 for device 00:13.0
HPT370: chipset revision 3
HPT370: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:DMA, hdf:pio
ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:pio
hdc: CD-ROM 52X/AKH, ATAPI CD/DVD-ROM drive
hdd: MATSHITA CD-RW CW-7585, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307030, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
ide2 at 0xd400-0xd407,0xd802 on irq 11
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(100)
hdc: ATAPI 52X CD-ROM drive, 192kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
hdd: ATAPI 32X CD-ROM CD-R/RW drive, 2048kB Cache, DMA
Partition check:
hde: [PTBL] [3737/255/63] hde1 hde2 < hde5 hde6 hde7 hde8 hde9 hde10 >
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 1500 blocks [1 disk] into ram disk...
|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/-\|/done.
Freeing initrd memory: 1500k freed
Serial driver version 5.02 (2000-08-09) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ
SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
autodetecting RAID arrays
autorun ...
... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
Linux IP multicast router 0.06 plus PIM-SM
IP-Config: No network devices available.
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=3
Trying to unmount old root ... okay
Freeing unused kernel memory: 224k freed
Adding Swap: 257000k swap-space (priority -1)
SCSI subsystem driver Revision: 1.00
aha152x: BIOS test: passed, detected 1 controller(s)
aha152x: resetting bus...
aha152x0: vital data: rev=3, io=0x140 (0x140/0x140), irq=9, scsiid=7,
reconnect=enabled, parity=enabled, synchronous=disabled, delay=1000, extended
translation=disabled
aha152x0: trying software interrupt, lost.
aha152x0: IRQ 9 possibly wrong. Please verify.
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
PCI: Found IRQ 10 for device 00:0d.0
PCI: The same IRQ used for device 00:0f.0
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.251 $ time 02:23:32 Feb 27 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:07.2
PCI: The same IRQ used for device 00:07.3
usb-uhci.c: USB UHCI at I/O 0xc400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:07.3
PCI: The same IRQ used for device 00:07.2
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
8139too Fast Ethernet driver 0.9.15 loaded
PCI: Found IRQ 10 for device 00:0f.0
PCI: The same IRQ used for device 00:0d.0
eth0: RealTek RTL8139 Fast Ethernet at 0xd289c000, 00:48:54:8c:45:36, IRQ 10
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 41e1.
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
parport0: cpp_daisy: aa5500ff(98)
parport0: assign_addrs: aa5500ff(98)
parport0: Printer, Samsung ML-6040
parport_pc: Via 686A parallel port: io=0x378, irq=7
lp0: using parport0 (interrupt-driven).
lp0: console ready
