I also want to add that I am also running a stock 2.4.18pre9 + O(1) + Preemption patches. With this,I can run pppd without crashing my system.
-Joe On Mon, 2002-03-11 at 19:25, Joseph Davidson wrote: > I have an Agenda VR3 that I am connecting to and exporting the display > to my PC (8.2 beta 4 just installed - Kernel is 2.4.18-2mdk). This will > work fine for a while, but when I open Konqueror, or let Evolution check > mail. Occasionally, I will get strange lock ups, and my PC has even > spontaniously restarted several times. In my /var/log/messages I find > several Oops's. (see below). > > Normally, when I am NOT connected to the VR3, the system has been > extremely stable. > > This problem was also present using beta 3. > > In order to connect to the VR3, I use the following command: > > /usr/sbin/pppd /dev/ttyS1 10.1.1.1:10.1.1.2 noauth nodetach debug 115200 > local > > My main Internet connection is through an Intel EtherExpress PRO/100+, > which is configured for DHCP, and is connect to a LinkSys DSL router. > > The output from dmesg is also listed below. > > Let me know if you need further info. > > -Joe > > > > > ---- > > > Mar 8 22:48:44 localhost kernel: CSLIP: code copyright 1989 Regents of the >University of California > Mar 8 22:48:44 localhost kernel: PPP generic driver version 2.4.1 > Mar 8 22:48:44 localhost pppd[24817]: pppd 2.4.1 started by root, uid 0 > Mar 8 22:48:44 localhost pppd[24817]: Using interface ppp0 > Mar 8 22:48:44 localhost pppd[24817]: Connect: ppp0 <--> /dev/ttyS1 > Mar 8 22:48:44 localhost /etc/hotplug/net.agent: assuming ppp0 is already up > Mar 8 22:48:50 localhost kernel: PPP BSD Compression module registered > Mar 8 22:48:50 localhost kernel: PPP Deflate Compression module registered > Mar 8 22:48:50 localhost pppd[24817]: Deflate (15) compression enabled > Mar 8 22:48:50 localhost pppd[24817]: local IP address 10.1.1.1 > Mar 8 22:48:50 localhost pppd[24817]: remote IP address 10.1.1.2 > Mar 8 22:54:18 localhost kernel: Unable to handle kernel paging request at virtual >address 77a8011e > Mar 8 22:54:18 localhost kernel: printing eip: > Mar 8 22:54:18 localhost kernel: c0115cb6 > Mar 8 22:54:18 localhost kernel: *pde = 00000000 > Mar 8 22:54:18 localhost kernel: Oops: 0002 > Mar 8 22:54:18 localhost kernel: CPU: 0 > Mar 8 22:54:18 localhost kernel: EIP: 0010:[add_wait_queue+22/48] Tainted: P > Mar 8 22:54:18 localhost kernel: EIP: 0010:[<c0115cb6>] Tainted: P > Mar 8 22:54:18 localhost kernel: EFLAGS: 00010046 > Mar 8 22:54:18 localhost kernel: eax: ca36bfa0 ebx: d6a9a02c ecx: 77a8011a >edx: d6a9a024 > Mar 8 22:54:18 localhost kernel: esi: ca36bfa4 edi: 00000246 ebp: 00000145 >esp: d34fdef8 > Mar 8 22:54:18 localhost kernel: ds: 0018 es: 0018 ss: 0018 > Mar 8 22:54:18 localhost kernel: Process kdeinit (pid: 24845, stackpage=d34fd000) > Mar 8 22:54:18 localhost kernel: Stack: c1b21b60 c43a7ca0 00000000 c013cb29 >c43a7ca0 ca36bfa0 d34fdf54 00000000 > Mar 8 22:54:18 localhost kernel: 00000000 c01d3b4f c312b6c0 00000000 >c43a7ca0 c014209c c43a7ca0 d34fdf54 > Mar 8 22:54:18 localhost kernel: d34fdf54 00000010 d34fc000 7fffffff >00000004 d34fdf54 00000008 00000000 > Mar 8 22:54:18 localhost kernel: Call Trace: [pipe_poll+41/112] [sock_poll+31/48] >[do_select+268/576] [sys_select+825/1168] [system_call+51/64] > Mar 8 22:54:18 localhost kernel: Call Trace: [<c013cb29>] [<c01d3b4f>] [<c014209c>] >[<c0142539>] [<c0106f23>] > Mar 8 22:54:18 localhost kernel: > Mar 8 22:54:18 localhost kernel: Code: 89 59 04 89 4a 08 89 73 04 89 58 04 57 9d 5b >5e 5f c3 90 8d > Mar 8 22:54:18 localhost kernel: <1>Unable to handle kernel paging request at >virtual address 77a80116 > Mar 8 22:54:18 localhost kernel: printing eip: > Mar 8 22:54:18 localhost kernel: c0114e32 > Mar 8 22:54:18 localhost kernel: *pde = 00000000 > Mar 8 22:54:18 localhost kernel: Oops: 0000 > Mar 8 22:54:18 localhost kernel: CPU: 0 > Mar 8 22:54:18 localhost kernel: EIP: 0010:[__wake_up+34/160] Tainted: P > Mar 8 22:54:18 localhost kernel: EIP: 0010:[<c0114e32>] Tainted: P > Mar 8 22:54:18 localhost kernel: EFLAGS: 00010883 > Mar 8 22:54:18 localhost kernel: eax: ca36bfa4 ebx: 77a8011a ecx: 00000001 >edx: 00000001 > Mar 8 22:54:18 localhost kernel: esi: c1b21b60 edi: 00000001 ebp: d34fdd3c >esp: d34fdd24 > Mar 8 22:54:18 localhost kernel: ds: 0018 es: 0018 ss: 0018 > Mar 8 22:54:18 localhost kernel: Process kdeinit (pid: 24845, stackpage=d34fd000) > Mar 8 22:54:18 localhost kernel: Stack: 00000286 00000001 ca36bfa0 ca36bfa0 >c1b21b60 c1b21b60 c7529da0 c013cbe8 > Mar 8 22:54:18 localhost kernel: c43a7e20 c1607260 c013cc2e c1b21b60 >00000000 00000001 c01352cd c1b21b60 > Mar 8 22:54:18 localhost kernel: c43a7e20 c3ec2bfc 00000001 00000000 >00000000 c43a7e20 00000000 00000001 > Mar 8 22:54:18 localhost kernel: Call Trace: [pipe_release+120/144] >[pipe_write_release+14/32] [fput+77/224] [filp_close+83/96] [put_files_struct+76/208] > Mar 8 22:54:18 localhost kernel: Call Trace: [<c013cbe8>] [<c013cc2e>] [<c01352cd>] >[<c01341e3>] [<c0119a2c>] > Mar 8 22:54:18 localhost kernel: [do_exit+194/496] [bust_spinlocks+62/80] >[die+70/96] [add_wait_queue+22/48] [add_wait_queue+22/48] [do_page_fault+935/1259] > Mar 8 22:54:18 localhost kernel: [<c011a062>] [<c0113fbe>] [<c01074d6>] >[<c0115cb6>] [<c0115cb6>] [<c01143a7>] > Mar 8 22:54:18 localhost kernel: [unix_write_space+55/112] >[filemap_nopage+189/528] [filemap_nopage+235/528] [__kfree_skb+291/304] >[do_page_fault+0/1259] [error_code+52/64] > Mar 8 22:54:18 localhost kernel: [<c0217a57>] [<c012843d>] [<c012846b>] >[<c01d6aa3>] [<c0114000>] [<c0107034>] > Mar 8 22:54:18 localhost kernel: [sys_rt_sigtimedwait+200/752] >[add_wait_queue+22/48] [pipe_poll+41/112] [sock_poll+31/48] [do_select+268/576] >[sys_select+825/1168] > Mar 8 22:54:18 localhost kernel: [<c0120018>] [<c0115cb6>] [<c013cb29>] >[<c01d3b4f>] [<c014209c>] [<c0142539>] > Mar 8 22:54:18 localhost kernel: [system_call+51/64] > Mar 8 22:54:18 localhost kernel: [<c0106f23>] > Mar 8 22:54:18 localhost kernel: > Mar 8 22:54:18 localhost kernel: Code: 8b 4b fc 8b 01 85 45 ec 74 55 31 c0 9c 5e fa >c7 01 00 00 00 > Mar 8 22:54:20 localhost kernel: <1>Unable to handle kernel paging request at >virtual address 77a80116 > Mar 8 22:54:20 localhost kernel: printing eip: > Mar 8 22:54:20 localhost kernel: c0114e32 > Mar 8 22:54:20 localhost kernel: *pde = 00000000 > Mar 8 22:54:20 localhost kernel: Oops: 0000 > Mar 8 22:54:20 localhost kernel: CPU: 0 > Mar 8 22:54:20 localhost kernel: EIP: 0010:[__wake_up+34/160] Tainted: P > Mar 8 22:54:20 localhost kernel: EIP: 0010:[<c0114e32>] Tainted: P > Mar 8 22:54:20 localhost kernel: EFLAGS: 00010883 > Mar 8 22:54:20 localhost kernel: eax: ca36bfa4 ebx: 77a8011a ecx: 00000001 >edx: 00000001 > Mar 8 22:54:20 localhost kernel: esi: d704a3c0 edi: 00000001 ebp: c433df44 >esp: c433df2c > Mar 8 22:54:20 localhost kernel: ds: 0018 es: 0018 ss: 0018 > Mar 8 22:54:20 localhost kernel: Process kdeinit (pid: 24844, stackpage=c433d000) > Mar 8 22:54:20 localhost kernel: Stack: 00000286 00000001 ca36bfa0 ca36bfa0 >d704a3c0 d704a3c0 c751b2e0 c013cbe8 > Mar 8 22:54:20 localhost kernel: ce7717a0 c1607260 c013cc0e d704a3c0 >00000001 00000000 c01352cd d704a3c0 > Mar 8 22:54:20 localhost kernel: ce7717a0 d704a6e4 d704a6e4 0805b028 >c7650000 ce7717a0 00000000 00000000 > Mar 8 22:54:20 localhost kernel: Call Trace: [pipe_release+120/144] >[pipe_read_release+14/32] [fput+77/224] [filp_close+83/96] [sys_close+67/80] > Mar 8 22:54:20 localhost kernel: Call Trace: [<c013cbe8>] [<c013cc0e>] [<c01352cd>] >[<c01341e3>] [<c0134233>] > Mar 8 22:54:20 localhost kernel: [system_call+51/64] > Mar 8 22:54:18 localhost kernel: [<c0106f23>] > Mar 8 22:54:18 localhost kernel: > Mar 8 22:54:18 localhost kernel: Code: 8b 4b fc 8b 01 85 45 ec 74 55 31 c0 9c 5e fa >c7 01 00 00 00 > Mar 8 22:54:20 localhost kernel: <1>Unable to handle kernel paging request at >virtual address 77a80116 > Mar 8 22:54:20 localhost kernel: printing eip: > Mar 8 22:54:20 localhost kernel: c0114e32 > Mar 8 22:54:20 localhost kernel: *pde = 00000000 > Mar 8 22:54:20 localhost kernel: Oops: 0000 > Mar 8 22:54:20 localhost kernel: CPU: 0 > Mar 8 22:54:20 localhost kernel: EIP: 0010:[__wake_up+34/160] Tainted: P > Mar 8 22:54:20 localhost kernel: EIP: 0010:[<c0114e32>] Tainted: P > Mar 8 22:54:20 localhost kernel: EFLAGS: 00010883 > Mar 8 22:54:20 localhost kernel: eax: ca36bfa4 ebx: 77a8011a ecx: 00000001 >edx: 00000001 > Mar 8 22:54:20 localhost kernel: esi: d704a3c0 edi: 00000001 ebp: c433df44 >esp: c433df2c > Mar 8 22:54:20 localhost kernel: ds: 0018 es: 0018 ss: 0018 > Mar 8 22:54:20 localhost kernel: Process kdeinit (pid: 24844, stackpage=c433d000) > Mar 8 22:54:20 localhost kernel: Stack: 00000286 00000001 ca36bfa0 ca36bfa0 >d704a3c0 d704a3c0 c751b2e0 c013cbe8 > Mar 8 22:54:20 localhost kernel: ce7717a0 c1607260 c013cc0e d704a3c0 >00000001 00000000 c01352cd d704a3c0 > Mar 8 22:54:20 localhost kernel: ce7717a0 d704a6e4 d704a6e4 0805b028 >c7650000 ce7717a0 00000000 00000000 > Mar 8 22:54:20 localhost kernel: Call Trace: [pipe_release+120/144] >[pipe_read_release+14/32] [fput+77/224] [filp_close+83/96] [sys_close+67/80] > Mar 8 22:54:20 localhost kernel: Call Trace: [<c013cbe8>] [<c013cc0e>] [<c01352cd>] >[<c01341e3>] [<c0134233>] > Mar 8 22:54:20 localhost kernel: [system_call+51/64] > Mar 8 22:54:20 localhost kernel: [<c0106f23>] > Mar 8 22:54:20 localhost kernel: > Mar 8 22:54:20 localhost kernel: Code: 8b 4b fc 8b 01 85 45 ec 74 55 31 c0 9c 5e fa >c7 01 00 00 00 > Mar 8 22:57:20 localhost syslogd 1.4.1: restart. > > ---- > > > 68 (order: 6, 262144 bytes) > Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) > Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes) > Page-cache hash table entries: 131072 (order: 7, 524288 bytes) > CPU: Before vendor init, caps: 0383fbff 00000000 00000000, vendor = 0 > CPU: L1 I cache: 16K, L1 D cache: 16K > CPU: L2 cache: 512K > CPU: After vendor init, caps: 0383fbff 00000000 00000000 00000000 > Intel machine check architecture supported. > Intel machine check reporting enabled on CPU#0. > CPU: After generic, caps: 0383fbff 00000000 00000000 00000000 > CPU: Common caps: 0383fbff 00000000 00000000 00000000 > CPU: Intel Pentium III (Katmai) stepping 02 > Enabling fast FPU save and restore... done. > Enabling unmasked SIMD FPU exception support... done. > Checking 'hlt' instruction... OK. > POSIX conformance testing by UNIFIX > mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED]) > mtrr: detected mtrr type: Intel > PCI: PCI BIOS revision 2.10 entry at 0xfd9b4, last bus=1 > PCI: Using configuration type 1 > PCI: Probing PCI hardware > Unknown bridge resource 0: assuming transparent > PCI: Using IRQ router PIIX [8086/7110] at 00:07.0 > Limiting direct PCI/PCI transfers. > isapnp: Scanning for PnP cards... > isapnp: Card 'DIAMOND SupraExpress 56I SP V.90' > isapnp: 1 Plug & Play card detected total > Linux NET4.0 for Linux 2.4 > Based upon Swansea University Computer Society NET3.039 > Initializing RT netlink socket > apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16) > Starting kswapd > VFS: Diskquotas version dquot_6.5.0 initialized > devfs: v1.10 (20020120) Richard Gooch ([EMAIL PROTECTED]) > devfs: boot_options: 0x1 > pty: 256 Unix98 ptys configured > Serial driver version 5.05c (2001-07-08) with HUB-6 MANY_PORTS MULTIPORT SHARE_IRQ >SERIAL_PCI ISAPNP enabled > ttyS00 at 0x03f8 (irq = 4) is a 16550A > ttyS01 at 0x02f8 (irq = 3) is a 16550A > ttyS02 at port 0x03e8 (irq = 4) is a 16550A > block: 128 slots per queue, batch=32 > RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize > Uniform Multi-Platform E-IDE driver Revision: 6.31 > ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx > PIIX4: IDE controller on PCI bus 00 dev 39 > PIIX4: chipset revision 1 > PIIX4: not 100% native mode: will probe irqs later > ide0: BM-DMA at 0x10e0-0x10e7, BIOS settings: hda:DMA, hdb:DMA > ide1: BM-DMA at 0x10e8-0x10ef, BIOS settings: hdc:DMA, hdd:pio > hda: FUJITSU MPE3136AT, ATA DISK drive > hdb: Maxtor 90845D4, ATA DISK drive > hdc: SONY CD-RW CRX120E, ATAPI CD/DVD-ROM drive > hdd: IOMEGA ZIP 100 ATAPI, ATAPI FLOPPY drive > ide2: ports already in use, skipping probe > ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 > ide1 at 0x170-0x177,0x376 on irq 15 > hda: 26688576 sectors (13665 MB) w/512KiB Cache, CHS=1661/255/63, UDMA(33) > hdb: 16514064 sectors (8455 MB) w/512KiB Cache, CHS=1027/255/63, UDMA(33) > Partition check: > /dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 > > /dev/ide/host0/bus0/target1/lun0: p1 p2 p3 < p5 > > floppy0: no floppy controllers found > md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. > NET4: Linux TCP/IP 1.0 for NET4.0 > IP Protocols: ICMP, UDP, TCP, IGMP > IP: routing cache hash table of 4096 buckets, 32Kbytes > TCP: Hash tables configured (established 32768 bind 32768) > Linux IP multicast router 0.06 plus PIM-SM > NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. > RAMDISK: Compressed image found at block 0 > Uncompressing..........done. > Freeing initrd memory: 219k freed > VFS: Mounted root (ext2 filesystem). > Mounted devfs on /dev > SCSI subsystem driver Revision: 1.00 > PCI: Found IRQ 9 for device 00:0e.0 > scsi0 : AdvanSys SCSI 3.3G: PCI Ultra-Wide: PCIMEM 0xD8835000-0xD883503F, IRQ 0x9 > Vendor: WDIGTL Model: WDE9150 ULTRA2 Rev: 1.30 > Type: Direct-Access ANSI SCSI revision: 02 > Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 > SCSI device sda: 17873040 512-byte hdwr sectors (9151 MB) > /dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 > > Journalled Block Device driver loaded > EXT3-fs: INFO: recovery required on readonly filesystem. > EXT3-fs: write access will be enabled during recovery. > kjournald starting. Commit interval 5 seconds > EXT3-fs: sd(8,5): orphan cleanup on readonly fs > ext3_orphan_cleanup: deleting unreferenced inode 308732 > EXT3-fs: sd(8,5): 1 orphan inode deleted > EXT3-fs: recovery complete. > EXT3-fs: mounted filesystem with ordered data mode. > Freeing unused kernel memory: 260k freed > Real Time Clock Driver v1.10e > EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,5), internal journal > Adding Swap: 248968k swap-space (priority -1) > i2c-core.o: i2c core module version 2.6.2 (20011118) > i2c-algo-bit.o: i2c bit algorithm module version 2.6.2 (20011118) > Linux video capture interface: v1.00 > bttv: driver version 0.7.83 loaded > bttv: using 2 buffers with 2080k (4160k total) for capture > bttv: Host bridge is Intel Corp. 440BX/ZX - 82443BX/ZX Host bridge > bttv: Host bridge needs ETBF enabled. > bttv: Bt8xx card found (0). > PCI: Found IRQ 9 for device 00:10.0 > PCI: Sharing IRQ 9 with 00:07.2 > PCI: Sharing IRQ 9 with 00:10.1 > bttv0: Bt878 (rev 2) at 00:10.0, irq: 9, latency: 132, memory: 0xe8102000 > bttv0: detected: Hauppauge WinTV [card=10], PCI subsystem ID is 0070:13eb > bttv0: using: BT878(Hauppauge (bt878)) [card=10,autodetected] > bttv0: enabling ETBF (430FX/VP3 compatibilty) > bttv0: Hauppauge/Voodoo msp34xx: reset line init [5] > i2c-core.o: adapter bt848 #0 registered as adapter 0. > bttv0: Hauppauge eeprom: model=38101, tuner=Philips FI1236 MK2 (2), radio=no > bttv0: i2c: checking for MSP34xx @ 0x80... not found > bttv0: i2c: checking for TDA9875 @ 0xb0... not found > bttv0: i2c: checking for TDA7432 @ 0x8a... not found > tvaudio: TV audio decoder + audio/video mux driver > tvaudio: known chips: >tda9840,tda9873h,tda9874a,tda9850,tda9855,tea6300,tea6420,tda8425,pic16c54 (PV951) > i2c-core.o: driver generic i2c audio driver registered. > i2c-core.o: driver i2c TV tuner driver registered. > tuner: chip found @ 0xc2 > bttv0: i2c attach [client=Philips NTSC,ok] > i2c-core.o: client [Philips NTSC] registered to adapter [bt848 #0](pos. 0). > scsi1 : SCSI host adapter emulation for IDE ATAPI devices > Vendor: IOMEGA Model: ZIP 100 Rev: 13.A > Type: Direct-Access ANSI SCSI revision: 00 > Vendor: SONY Model: CD-RW CRX120E Rev: 1.0j > Type: CD-ROM ANSI SCSI revision: 02 > Attached scsi removable disk sdb at scsi1, channel 0, id 0, lun 0 > sdb : READ CAPACITY failed. > sdb : status = 0, message = 00, host = 0, driver = 28 > Current sd00:00: sense key Not Ready > Additional sense indicates Medium not present > sdb : block size assumed to be 512 bytes, disk size 1GB. > /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0 > I/O error: dev 08:10, sector 0 > unable to read partition table > Device not ready. Make sure there is a disc in the drive. > VFS: Disk change detected on device 08:10 > sdb : READ CAPACITY failed. > sdb : status = 0, message = 00, host = 0, driver = 28 > Current sd00:00: sense key Not Ready > Additional sense indicates Medium not present > sdb : block size assumed to be 512 bytes, disk size 1GB. > /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0 > I/O error: dev 08:10, sector 0 > Device not ready. Make sure there is a disc in the drive. > VFS: Disk change detected on device 08:10 > sdb : READ CAPACITY failed. > sdb : status = 0, message = 00, host = 0, driver = 28 > Current sd00:00: sense key Not Ready > Additional sense indicates Medium not present > sdb : block size assumed to be 512 bytes, disk size 1GB. > /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0 > I/O error: dev 08:10, sector 0 > Device not ready. Make sure there is a disc in the drive. > VFS: Disk change detected on device 08:10 > sdb : READ CAPACITY failed. > sdb : status = 0, message = 00, host = 0, driver = 28 > Current sd00:00: sense key Not Ready > Additional sense indicates Medium not present > sdb : block size assumed to be 512 bytes, disk size 1GB. > /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0 > I/O error: dev 08:10, sector 0 > Device not ready. Make sure there is a disc in the drive. > VFS: Disk change detected on device 08:10 > sdb : READ CAPACITY failed. > sdb : status = 0, message = 00, host = 0, driver = 28 > Current sd00:00: sense key Not Ready > Additional sense indicates Medium not present > sdb : block size assumed to be 512 bytes, disk size 1GB. > /dev/scsi/host1/bus0/target0/lun0: I/O error: dev 08:10, sector 0 > I/O error: dev 08:10, sector 0 > kjournald starting. Commit interval 5 seconds > EXT3 FS 2.4-0.9.17, 10 Jan 2002 on sd(8,7), internal journal > EXT3-fs: mounted filesystem with ordered data mode. > MSDOS FS: IO charset iso8859-1 > MSDOS FS: Using codepage 850 > MSDOS FS: IO charset iso8859-1 > MSDOS FS: Using codepage 850 > EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended > eepro100.c:v1.09j-t 9/29/99 Donald Becker http://www.scyld.com/network/eepro100.html > eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin ><[EMAIL PROTECTED]> and others > PCI: Found IRQ 11 for device 00:0d.0 > PCI: Sharing IRQ 11 with 01:00.0 > eth0: Intel Corp. 82557 [Ethernet Pro 100], 00:90:27:76:23:E3, I/O at 0x1000, IRQ 11. > Board assembly 721383-006, Physical connectors present: RJ45 > Primary interface chip i82555 PHY #1. > General self-test: passed. > Serial sub-system self-test: passed. > Internal registers self-test: passed. > ROM checksum self-test: passed (0x04f4518b). > usb.c: registered new driver usbdevfs > usb.c: registered new driver hub > usb-uhci.c: $Revision: 1.275 $ time 17:29:12 Feb 28 2002 > usb-uhci.c: High bandwidth mode enabled > PCI: Found IRQ 9 for device 00:07.2 > PCI: Sharing IRQ 9 with 00:10.0 > PCI: Sharing IRQ 9 with 00:10.1 > usb-uhci.c: USB UHCI at I/O 0x10c0, IRQ 9 > usb-uhci.c: Detected 2 ports > usb.c: new USB bus registered, assigned bus number 1 > hub.c: USB hub found > hub.c: 2 ports detected > usb-uhci.c: v1.275:USB Universal Host Controller Interface driver > hub.c: USB new device connect on bus1/2, assigned device number 2 > usb.c: USB device 2 (vend/prod 0x45e/0x1e) is not claimed by any active driver. > usb.c: registered new driver usb_mouse > usb-uhci.c: interrupt, status 3, frame# 1371 > input0: Microsoft Microsoft IntelliMouse® Explorer on usb1:2.0 > usbmouse.c: v1.6:USB HID Boot Protocol mouse driver > usb.c: registered new driver hiddev > usb.c: registered new driver hid > hid-core.c: v1.8 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]> > hid-core.c: USB HID support drivers > mice: PS/2 mouse device common for all mice > parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] > parport0: irq 7 detected > parport0: faking semi-colon > parport0: Printer, HEWLETT-PACKARD DESKJET 710C > parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE] > parport0: irq 7 detected > parport0: faking semi-colon > parport0: Printer, HEWLETT-PACKARD DESKJET 710C > lp0: using parport0 (polling). > lp0: compatibility mode > > >
