Hi all, Most of you already received the email displayed below. Later that day I spoke Uwe on IRC and he told me he had fogot to tell me I had to include the irq_tables.c as generated by getpir as well. So, here it is in the attachments. In case your mailing systems do not forward attachments, here are the contents of that file:
/* This file was generated by getpir.c, do not modify! * (but if you do, please run checkpir on it to verify) * * Contains the IRQ Routing Table dumped directly from your * memory, which BIOS sets up. * * Documentation at: http://www.microsoft.com/whdc/archive/pciirq.mspx */ #ifdef GETPIR #include "pirq_routing.h" #else #include <arch/pirq_routing.h> #endif const struct irq_routing_table intel_irq_routing_table = { PIRQ_SIGNATURE, /* u32 signature */ PIRQ_VERSION, /* u16 version */ 32+16*7, /* There can be total 7 devices on the bus */ 0x00, /* Where the interrupt router lies (bus) */ (0x07<<3)|0x0, /* Where the interrupt router lies (dev) */ 0x800, /* IRQs devoted exclusively to PCI usage */ 0x8086, /* Vendor */ 0x7000, /* Device */ 0, /* Crap (miniport) */ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */ 0x9c, /* u8 checksum. This has to be set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ { /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ {0x00,(0x0e<<3)|0x0, {{0x60, 0xdeb8}, {0x61, 0xdeb8}, {0x62, 0xdeb8}, {0x63, 0x0deb8}}, 0x1, 0x0}, {0x00,(0x10<<3)|0x0, {{0x61, 0xdeb8}, {0x62, 0xdeb8}, {0x63, 0xdeb8}, {0x60, 0x0deb8}}, 0x2, 0x0}, {0x00,(0x12<<3)|0x0, {{0x62, 0xdeb8}, {0x63, 0xdeb8}, {0x60, 0xdeb8}, {0x61, 0x0deb8}}, 0x3, 0x0}, {0x00,(0x14<<3)|0x0, {{0x63, 0xdeb8}, {0x60, 0xdeb8}, {0x61, 0xdeb8}, {0x62, 0x0deb8}}, 0x4, 0x0}, {0x00,(0x07<<3)|0x1, {{0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0}, {0x00,(0x07<<3)|0x2, {{0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x63, 0x0deb8}}, 0x0, 0x0}, {0x00,(0x01<<3)|0x0, {{0x60, 0xdeb8}, {0x61, 0xdeb8}, {0x62, 0xdeb8}, {0x63, 0x0deb8}}, 0x0, 0x0}, } }; greetz from Holland, Maarten "merethan" On Jan 13, 2008 12:50 PM, Maarten van Eeuwijk <[EMAIL PROTECTED]> wrote: > Hi all, > > A few day's ago I asked Uwe for a little help on my MS6119 board from MSI. > He adviced me to post the results of lspci -tvnn, superiotool -dV > and flashrom -V to the mailing list, for the sake of archiving. > So, after some creative wiring I got a LiveCD going and ran the pieces of > software mentioned above. > > The tests are done with minimal hardware, all the PCI slots were empty. > The only slots filled were the CPU slot and the AGP slot. > > For the ones who think they recognize a Asus p2b here, you're almost dead > on. The MS6119 has the same hardware and similair layout but the wiring is > likely to be different. > > Here are the results: > > *lspci -tvnn:* > -[0000:00]-+-00.0 8086:7190 > +-01.0-[0000:01]----00.0 1002:4742 > +-07.0 8086:7110 > +-07.1 8086:7111 > +-07.2 8086:7112 > \-07.3 8086:7113 > > > *superiotool -dV:* > superiotool r3011 > Probing for ALi Super I/O at 0x3f0... > Failed. Returned data: id=0xffff, rev=0xff > Probing for ALi Super I/O at 0x370... > Failed. Returned data: id=0xffff, rev=0xff > Probing for Fintek Super I/O at 0x2e... > Failed. Returned data: vid=0xffff, id=0xffff > Probing for Fintek Super I/O at 0x4e... > Failed. Returned data: vid=0xffff, id=0xffff > Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x2e... > Failed. Returned data: id=0xffff, rev=0xf > Probing for ITE Super I/O (init=0x87,0x87) at 0x2e... > Failed. Returned data: id=0xffff, rev=0xf > Probing for ITE Super I/O (init=0x87,0x01,0x55,0x55/0xaa) at 0x4e... > Failed. Returned data: id=0xffff, rev=0xf > Probing for ITE Super I/O (init=0x87,0x87) at 0x4e... > Failed. Returned data: id=0xffff, rev=0xf > Probing for NSC Super I/O at 0x2e... > Failed. Returned data: port=0xff, port+1=0xff > Probing for NSC Super I/O at 0x4e... > Failed. Returned data: port=0xff, port+1=0xff > Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x2e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x2e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x4e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x4e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x162e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x162e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x164e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x164e... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x3f0... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x3f0... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x20/0x21) at 0x370... > Failed. Returned data: id=0xff, rev=0xff > Probing for SMSC Super I/O (idregs=0x0d/0x0e) at 0x370... > Failed. Returned data: id=0xff, rev=0xff > Probing for Winbond Super I/O (init=0x88) at 0x2e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x89) at 0x2e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x86,0x86) at 0x2e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x87,0x87) at 0x2e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x88) at 0x4e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x89) at 0x4e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x86,0x86) at 0x4e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x87,0x87) at 0x4e... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x88) at 0x3f0... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x89) at 0x3f0... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x86,0x86) at 0x3f0... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x87,0x87) at 0x3f0... > Found Winbond W83977TF (id=0x97, rev=0x73) at 0x3f0 > Register dump: > idx 20 21 22 23 24 25 26 28 2a 2b 2c 2d 2e 2f > val 97 73 ff fe 84 00 00 00 00 00 00 00 00 ff > def 97 73 ff fe MM 00 MM 00 00 00 00 RR RR RR > LDN 0x00 (Floppy) > idx 30 60 61 70 74 f0 f1 f2 f4 f5 > val 01 03 f0 06 02 0e 00 ff 00 00 > def 01 03 f0 06 02 0e 00 ff 00 00 > LDN 0x01 (Parallel port) > idx 30 60 61 70 74 f0 > val 01 03 78 07 03 00 > def 01 03 78 07 04 3f > LDN 0x02 (COM1) > idx 30 60 61 70 f0 > val 01 03 f8 04 00 > def 01 03 f8 04 00 > LDN 0x03 (COM2) > idx 30 60 61 70 f0 f1 > val 01 02 f8 03 00 00 > def 01 02 f8 03 00 00 > LDN 0x05 (Keyboard / mouse) > idx 30 60 61 62 63 70 72 f0 > val 01 00 60 00 64 01 00 42 > def 01 00 60 00 64 01 0c 83 > LDN 0x07 (GPIO 1) > idx 30 60 61 62 63 64 65 70 72 e0 e1 e2 e3 e4 e5 e6 e7 f1 > val 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 00 > def 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 00 > LDN 0x08 (GPIO 2) > idx 30 60 61 70 72 e8 e9 ea eb ec ed ee f0 f1 f2 f3 f4 > val 01 00 00 00 00 10 01 01 01 01 08 01 00 ff 00 00 00 > def 00 00 00 00 00 01 01 01 01 01 01 01 00 RR 00 00 00 > LDN 0x09 (GPIO 3) > idx 30 60 61 62 63 64 65 70 72 e0 e1 e2 e3 e4 e5 e6 e7 f1 > val 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 00 > def 00 00 00 00 00 00 00 00 00 01 01 01 01 01 01 01 01 00 > LDN 0x0a (ACPI) > idx 30 60 61 62 63 64 65 70 e0 e1 02 e3 e4 f0 f1 f2 f3 f4 f5 f6 f7 fe ff > > val 00 00 00 00 00 00 00 00 00 00 ff 07 00 00 00 0f 07 00 00 00 00 00 00 > def 00 00 00 00 00 00 00 00 00 00 NA MM RR 00 00 00 00 00 00 00 00 RR RR > Probing for Winbond Super I/O (init=0x88) at 0x370... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x89) at 0x370... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x86,0x86) at 0x370... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x87,0x87) at 0x370... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x88) at 0x250... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x89) at 0x250... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x86,0x86) at 0x250... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > Probing for Winbond Super I/O (init=0x87,0x87) at 0x250... > Failed. Returned data: id/oldid=0xff/0x0f, rev=0xff > > > *flashrom -V:* > Calibrating delay loop... 100M loops per second. OK. > No LinuxBIOS table found. > Found chipset "PIIX4/PIIX4E/PIIX4M", enabling flash write... OK. > Probing for Am29F040B, 512 KB > probe_29f040b: id1 0x7f, id2 0x3f > Probing for Am29LV040B, 512 KB > probe_29f040b: id1 0x7f, id2 0x3f > Probing for Am29F016D, 2048 KB > probe_29f040b: id1 0xff, id2 0xff > Probing for AE49F2008, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for At29C040A, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for At29C020, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for At49F002(N), 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for At49F002(N)T, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for EN29F002(A)(N)T, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for EN29F002(A)(N)B, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for MBM29F400TC, 512 KB > probe_m29f400bt: id1 0x7f, id2 0x3f > Probing for MX29F002, 256 KB > probe_29f002: id1 0xda, id2 0x45 > Probing for MX25L4005, 512 KB > generic_spi_command called, but no SPI chipset detected > Probing for MX25L8005, 1024 KB > generic_spi_command called, but no SPI chipset detected > Probing for SST25VF040B, 512 KB > generic_spi_command called, but no SPI chipset detected > Probing for SST25VF016B, 2048 KB > generic_spi_command called, but no SPI chipset detected > Probing for SST29EE020A, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST28SF040A, 512 KB > probe_28sf040: id1 0x7f, id2 0x3f > Probing for SST39SF010A, 128 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST39SF020A, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST39SF040, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST39VF020, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF040B, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF040, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF020A, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF080A, 1024 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF002A/B, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF003A/B, 384 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF004A/B, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF008A, 1024 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for SST49LF004C, 512 KB > probe_49lfxxxc: id1 0x7f, id2 0x3f > Probing for SST49LF008C, 1024 KB > probe_49lfxxxc: id1 0x7f, id2 0x3f > Probing for SST49LF016C, 2048 KB > probe_49lfxxxc: id1 0xff, id2 0xff > Probing for SST49LF160C, 2048 KB > probe_49lfxxxc: id1 0xff, id2 0xff > Probing for Pm49FL002, 256 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for Pm49FL004, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for W29C011, 128 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for W29C040P, 512 KB > probe_jedec: id1 0xda, id2 0x45 > Probing for W29C020C, 256 KB > probe_jedec: id1 0xda, id2 0x45 > W29C020C found at physical address 0xfffc0000. > Flash part is W29C020C (256 KB). > No operations were specified. > > That's it. > > Uwe told me he could help me with hacking up a MS6119 target file with > this info. > Once the bios works, I 'll use it to make a router of that board utilizing > coreboot, m0n0wall, a few ethernet NIC's and a Compact flash card. > Once that works I will demonstrate it at school. Perhaps I 'll put it > against a Cisco router in a VS showdown on troughput. > Might be cool to beat a 800+ bucks Cisco machine with an old piece of > hardware I found in a trashbox. > > > tnx for your time, > > Maarten "merethan" >
/* This file was generated by getpir.c, do not modify! * (but if you do, please run checkpir on it to verify) * * Contains the IRQ Routing Table dumped directly from your * memory, which BIOS sets up. * * Documentation at: http://www.microsoft.com/whdc/archive/pciirq.mspx */ #ifdef GETPIR #include "pirq_routing.h" #else #include <arch/pirq_routing.h> #endif const struct irq_routing_table intel_irq_routing_table = { PIRQ_SIGNATURE, /* u32 signature */ PIRQ_VERSION, /* u16 version */ 32+16*7, /* There can be total 7 devices on the bus */ 0x00, /* Where the interrupt router lies (bus) */ (0x07<<3)|0x0, /* Where the interrupt router lies (dev) */ 0x800, /* IRQs devoted exclusively to PCI usage */ 0x8086, /* Vendor */ 0x7000, /* Device */ 0, /* Crap (miniport) */ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */ 0x9c, /* u8 checksum. This has to be set to some value that would give 0 after the sum of all bytes for this structure (including checksum) */ { /* bus, dev|fn, {link, bitmap}, {link, bitmap}, {link, bitmap}, {link, bitmap}, slot, rfu */ {0x00,(0x0e<<3)|0x0, {{0x60, 0xdeb8}, {0x61, 0xdeb8}, {0x62, 0xdeb8}, {0x63, 0x0deb8}}, 0x1, 0x0}, {0x00,(0x10<<3)|0x0, {{0x61, 0xdeb8}, {0x62, 0xdeb8}, {0x63, 0xdeb8}, {0x60, 0x0deb8}}, 0x2, 0x0}, {0x00,(0x12<<3)|0x0, {{0x62, 0xdeb8}, {0x63, 0xdeb8}, {0x60, 0xdeb8}, {0x61, 0x0deb8}}, 0x3, 0x0}, {0x00,(0x14<<3)|0x0, {{0x63, 0xdeb8}, {0x60, 0xdeb8}, {0x61, 0xdeb8}, {0x62, 0x0deb8}}, 0x4, 0x0}, {0x00,(0x07<<3)|0x1, {{0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0x0deb8}}, 0x0, 0x0}, {0x00,(0x07<<3)|0x2, {{0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x00, 0xdeb8}, {0x63, 0x0deb8}}, 0x0, 0x0}, {0x00,(0x01<<3)|0x0, {{0x60, 0xdeb8}, {0x61, 0xdeb8}, {0x62, 0xdeb8}, {0x63, 0x0deb8}}, 0x0, 0x0}, } };
-- coreboot mailing list [email protected] http://www.coreboot.org/mailman/listinfo/coreboot
