remove building warnings of mahogany(_fam10). About get_ide_dma66(), the SATA has port 5,6 as PATA emulation since SB700. I havent tried the IDE yet. It will be tested later. So we leave this function for furture.
Signed-off-by: Zheng Bao <zheng....@amd.com>
Index: src/mainboard/amd/mahogany/mptable.c
===================================================================
--- src/mainboard/amd/mahogany/mptable.c (revision 5265)
+++ src/mainboard/amd/mahogany/mptable.c (working copy)
@@ -39,7 +39,7 @@
extern void get_bus_conf(void);
-void *smp_write_config_table(void *v)
+static void *smp_write_config_table(void *v)
{
static const char sig[4] = "PCMP";
static const char oem[8] = "AMD ";
Index: src/mainboard/amd/mahogany/acpi_tables.c
===================================================================
--- src/mainboard/amd/mahogany/acpi_tables.c (revision 5265)
+++ src/mainboard/amd/mahogany/acpi_tables.c (working copy)
@@ -101,6 +101,7 @@
extern void get_bus_conf(void);
+#if CONFIG_ACPI_SSDTX_NUM >= 1
static void update_ssdtx(void *ssdtx, int i)
{
uint8_t *PCI;
@@ -122,6 +123,7 @@
/* FIXME: need to update the GSI id in the ssdtx too */
}
+#endif
unsigned long acpi_fill_ssdt_generator(unsigned long current, const
char *oem_table_id) {
k8acpi_write_vars();
Index: src/mainboard/amd/mahogany/mainboard.c
===================================================================
--- src/mainboard/amd/mahogany/mainboard.c (revision 5265)
+++ src/mainboard/amd/mahogany/mainboard.c (working copy)
@@ -25,6 +25,7 @@
#include <cpu/x86/msr.h>
#include <cpu/amd/mtrr.h>
#include <device/pci_def.h>
+#include <arch/coreboot_tables.h>
#include <../southbridge/amd/sb700/sb700.h>
#include "chip.h"
@@ -35,6 +36,9 @@
uint64_t uma_memory_base, uma_memory_size;
+void set_pcie_dereset(void);
+void set_pcie_reset(void);
+
/*
* Mahogany uses GPIO 6 as PCIe slot reset, GPIO4 as GFX slot reset. We
need to
* pull it up before training the slot.
@@ -65,12 +69,13 @@
pci_write_config16(sm_dev, 0xA8, word);
}
+#if 0 /* not tested yet */
/********************************************************
-* mahogany uses SB700 GPIO8 to detect IDE_DMA66.
-* IDE_DMA66 is routed to GPIO 8. So we read Gpio 8 to
+* mahogany uses SB700 GPIO9 to detect IDE_DMA66.
+* IDE_DMA66 is routed to GPIO 9. So we read Gpio 9 to
* get the cable type, 40 pin or 80 pin?
********************************************************/
-static void get_ide_dma66()
+static void get_ide_dma66(void)
{
u8 byte;
/*u32 sm_dev, ide_dev; */
@@ -79,27 +84,29 @@
sm_dev = dev_find_slot(0, PCI_DEVFN(0x14, 0));
byte = pci_read_config8(sm_dev, 0xA9);
- byte |= (1 << 4); /* Set Gpio8 as input */
+ byte |= (1 << 5); /* Set Gpio9 as input */
pci_write_config8(sm_dev, 0xA9, byte);
ide_dev = dev_find_slot(0, PCI_DEVFN(0x14, 1));
byte = pci_read_config8(ide_dev, 0x56);
byte &= ~(7 << 0);
- if ((1 << 4) & pci_read_config8(sm_dev, 0xAA))
+ if ((1 << 5) & pci_read_config8(sm_dev, 0xAA))
byte |= 2 << 0; /* mode 2 */
else
byte |= 5 << 0; /* mode 5 */
pci_write_config8(ide_dev, 0x56, byte);
}
+#endif /* get_ide_dma66 */
/*************************************************
* enable the dedicated function in mahogany board.
* This function called early than rs780_enable.
*************************************************/
-void mahogany_enable(device_t dev)
+static void mahogany_enable(device_t dev)
{
- struct mainboard_config *mainboard =
- (struct mainboard_config *)dev->chip_info;
+ /* Leave it for future. */
+ /* struct mainboard_config *mainboard =
+ (struct mainboard_config *)dev->chip_info;*/
printk_info("Mainboard MAHOGANY Enable. dev=0x%p\n", dev);
@@ -153,11 +160,12 @@
* in some circumstances we want the memory mentioned as
reserved.
*/
#if (CONFIG_GFXUMA == 1)
- printk_info("uma_memory_start=0x%x, uma_memory_size=0x%x \n",
- uma_memory_base, uma_memory_size);
+ printk_info("uma_memory_start=0x%llx, uma_memory_size=0x%llx
\n",
+ uma_memory_base, uma_memory_size);
lb_add_memory_range(mem, LB_MEM_RESERVED,
uma_memory_base, uma_memory_size);
#endif
+ return 0;
}
struct chip_operations mainboard_ops = {
Index: src/mainboard/amd/mahogany/get_bus_conf.c
===================================================================
--- src/mainboard/amd/mahogany/get_bus_conf.c (revision 5265)
+++ src/mainboard/amd/mahogany/get_bus_conf.c (working copy)
@@ -63,6 +63,8 @@
static u32 get_bus_conf_done = 0;
+void get_bus_conf(void);
+
void get_bus_conf(void)
{
u32 apicid_base;
Index: src/mainboard/amd/mahogany_fam10/acpi_tables.c
===================================================================
--- src/mainboard/amd/mahogany_fam10/acpi_tables.c (revision 5265)
+++ src/mainboard/amd/mahogany_fam10/acpi_tables.c (working copy)
@@ -92,7 +92,8 @@
extern void get_bus_conf(void);
extern void update_ssdt(void *ssdt);
-
+/* not tested yet. */
+#if 0 /* #if 0 //CONFIG_ACPI_SSDTX_NUM >= 1 */
static void update_ssdtx(void *ssdtx, int i)
{
u8 *PCI;
@@ -115,6 +116,7 @@
/* FIXME: need to update the GSI id in the ssdtx too */
}
+#endif
unsigned long write_acpi_tables(unsigned long start)
{
@@ -129,11 +131,7 @@
acpi_facs_t *facs;
acpi_header_t *dsdt;
acpi_header_t *ssdt;
- acpi_header_t *ssdtx;
- u8 *p;
- int i;
-
get_bus_conf(); //it will get sblk, pci1234, hcdn, and sbdn
/* Align ACPI tables to 16 bytes */
Index: src/mainboard/amd/mahogany_fam10/devicetree.cb
===================================================================
--- src/mainboard/amd/mahogany_fam10/devicetree.cb (revision 5265)
+++ src/mainboard/amd/mahogany_fam10/devicetree.cb (working copy)
@@ -143,5 +143,3 @@
# end
end
-
-
Index: src/mainboard/amd/mahogany_fam10/romstage.c
===================================================================
--- src/mainboard/amd/mahogany_fam10/romstage.c (revision 5265)
+++ src/mainboard/amd/mahogany_fam10/romstage.c (working copy)
@@ -298,4 +298,3 @@
post_cache_as_ram(); // BSP switch stack to ram, copy then
execute LB.
post_code(0x43); // Should never see this post code.
}
-
Index: src/mainboard/amd/mahogany_fam10/mptable.c
===================================================================
--- src/mainboard/amd/mahogany_fam10/mptable.c (revision 5265)
+++ src/mainboard/amd/mahogany_fam10/mptable.c (working copy)
@@ -39,7 +39,7 @@
extern void get_bus_conf(void);
-void *smp_write_config_table(void *v)
+static void *smp_write_config_table(void *v)
{
static const char sig[4] = "PCMP";
static const char oem[8] = "AMD ";
Index: src/mainboard/amd/mahogany_fam10/mainboard.c
===================================================================
--- src/mainboard/amd/mahogany_fam10/mainboard.c (revision 5265)
+++ src/mainboard/amd/mahogany_fam10/mainboard.c (working copy)
@@ -25,6 +25,7 @@
#include <cpu/x86/msr.h>
#include <cpu/amd/mtrr.h>
#include <device/pci_def.h>
+#include <arch/coreboot_tables.h>
#include <../southbridge/amd/sb700/sb700.h>
#include "chip.h"
@@ -35,6 +36,9 @@
uint64_t uma_memory_base, uma_memory_size;
+void set_pcie_dereset(void);
+void set_pcie_reset(void);
+
/*
* Mahogany uses GPIO 6 as PCIe slot reset, GPIO4 as GFX slot reset. We
need to
* pull it up before training the slot.
@@ -65,12 +69,13 @@
pci_write_config16(sm_dev, 0xA8, word);
}
+#if 0 /* not tested yet. */
/********************************************************
-* mahogany uses SB700 GPIO8 to detect IDE_DMA66.
-* IDE_DMA66 is routed to GPIO 8. So we read Gpio 8 to
+* mahogany uses SB700 GPIO9 to detect IDE_DMA66.
+* IDE_DMA66 is routed to GPIO 9. So we read Gpio 9 to
* get the cable type, 40 pin or 80 pin?
********************************************************/
-static void get_ide_dma66()
+static void get_ide_dma66(void)
{
u8 byte;
/*u32 sm_dev, ide_dev; */
@@ -79,27 +84,29 @@
sm_dev = dev_find_slot(0, PCI_DEVFN(0x14, 0));
byte = pci_read_config8(sm_dev, 0xA9);
- byte |= (1 << 4); /* Set Gpio8 as input */
+ byte |= (1 << 5); /* Set Gpio8 as input */
pci_write_config8(sm_dev, 0xA9, byte);
ide_dev = dev_find_slot(0, PCI_DEVFN(0x14, 1));
byte = pci_read_config8(ide_dev, 0x56);
byte &= ~(7 << 0);
- if ((1 << 4) & pci_read_config8(sm_dev, 0xAA))
+ if ((1 << 5) & pci_read_config8(sm_dev, 0xAA))
byte |= 2 << 0; /* mode 2 */
else
byte |= 5 << 0; /* mode 5 */
pci_write_config8(ide_dev, 0x56, byte);
}
+#endif /* get_ide_dma66() */
/*************************************************
* enable the dedicated function in mahogany board.
* This function called early than rs780_enable.
*************************************************/
-void mahogany_enable(device_t dev)
+static void mahogany_enable(device_t dev)
{
- struct mainboard_config *mainboard =
- (struct mainboard_config *)dev->chip_info;
+ /* Leave it for furture use. */
+ /* struct mainboard_config *mainboard =
+ (struct mainboard_config *)dev->chip_info; */
printk_info("Mainboard MAHOGANY Enable. dev=0x%p\n", dev);
@@ -153,11 +160,12 @@
* in some circumstances we want the memory mentioned as
reserved.
*/
#if (CONFIG_GFXUMA == 1)
- printk_info("uma_memory_start=0x%x, uma_memory_size=0x%x \n",
- uma_memory_base, uma_memory_size);
+ printk_info("uma_memory_start=0x%llx, uma_memory_size=0x%llx
\n",
+ uma_memory_base, uma_memory_size);
lb_add_memory_range(mem, LB_MEM_RESERVED,
uma_memory_base, uma_memory_size);
#endif
+ return 0;
}
struct chip_operations mainboard_ops = {
mahogany_remove_warnings.patch
Description: mahogany_remove_warnings.patch
-- coreboot mailing list: coreboot@coreboot.org http://www.coreboot.org/mailman/listinfo/coreboot
