With available data. It is most likely that it might have stuck somewhere in function https://review.coreboot.org/cgit/coreboot.git/tree/src/soc/intel/skylake/chip_fsp20.c#n169 You can add printk in that function & other functions called by it to bisect & confirm the exact position of hang.. Also can you please check FSP binary version you are using versus FSP header version checked-out in coreboot(which is currently 2.9.2). They should be
On Fri, Sep 14, 2018 at 7:55 PM Jose Trujillo via coreboot <coreboot@coreboot.org> wrote: > > Here is Naresh.... > > ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ > On Friday, September 14, 2018 4:49 PM, Naresh G. Solanki > <naresh.solanki.2...@gmail.com> wrote: > > Can you also provide latest complete log. > > On Fri 14 Sep, 2018, 2:10 PM Jose Trujillo via coreboot, > <coreboot@coreboot.org> wrote: >> >> Thank you Naresh, >> >> I added the missing PCH device id following your advise, also enabled >> DEBUG_BOOT_STATE but I am still not able to get more information via serial >> debug about the exact location of the problem (but now I am certain is in >> the coreboot code not in FSP). >> >> I suspect the code involved aound this issue is hardwaremain.c and >> device.c.... >> >> >> Only the first "boot" just after flash I notice that the ethernet and SATA >> LEDs blink for a fraction of a second then reboots. >> After that, the following attempts to boot I don't see LED activity neither >> reboots, just halted in some kind of loop. >> >> According to the serial dump the las printed text is "0x71" but my question >> is if the serial port gets broken still during "BS_DEV_INIT_CHIPS" or is >> already doing "BS_DEV_ENUMERATE". >> >> As Naresh pointed my PCH H chipset "Kabylake-H HM175" was not added to the >> list; I added it but may be is needed to do something else to make it work. >> Or istill is misconfigured (attached my .config file for your review)... I >> someone has a similar system working and want to share its configuration >> files to compare them myself I will be grateful. >> >> Jose Trujillo. >> >> ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ >> On Wednesday, 12 September 2018 19:33, Naresh G. Solanki >> <naresh.solanki.2...@gmail.com> wrote: >> >> Hi >> >> >PCH: device id a152 (rev 31) is Unknown >> >> This indicates that LPCID 0xa152 is not added. >> >> The #define should be added in source path: >> https://review.coreboot.org/cgit/coreboot.git/tree/src/include/device/pci_ids.h#n2721 >> >> https://review.coreboot.org/cgit/coreboot.git/tree/src/soc/intel/common/block/lpc/lpc.c#n131 >> >> & >> >> https://review.coreboot.org/cgit/coreboot.git/tree/src/soc/intel/skylake/bootblock/report_platform.c#n73 >> >> as well. >> >> >> >> Additionally you can enable config DEBUG_BOOT_STATE to understand where >> exactly its stuck. >> >> >> Regards, >> >> Naresh G. Solanki >> >> >> On Wed, Sep 12, 2018 at 9:24 PM Jose Trujillo via coreboot >> <coreboot@coreboot.org> wrote: >>> >>> Dear All, >>> About the memory I just changed the dimm to address A0 and now coreboot is >>> reporting correctly 1 dimm detected. >>> >>> But still no luck on the 0x71 post code loop (looks it is in some kind of >>> loop because is still responsive to power and reset buttons). >>> I don't know where this loop could be located (coreboot or FSP). >>> The description on the post_codes.h file shows the following: >>> .... >>> /** >>> * \brief Initializing Chips >>> * >>> * Boot State Machine: bs_dev_init_chips() >>> */ >>> #define POST_BS_DEV_INIT_CHIPS 0x71 >>> .... >>> >>> Any advice on this issue? >>> Attached is the serial dump with extra information. >>> >>> Thank you >>> Jose Trujillo >>> >>> ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ >>> On Wednesday, 12 September 2018 16:12, Jose Trujillo >>> <ce.au...@protonmail.com> wrote: >>> >>> To begin with the system didn't find memory attached... >>> but there is memory attached, SPD address mismatch? I will check. >>> .... >>> .......Timeout while sending command 0x0d to EC! >>> recv_ec_data: 0xff >>> recv_ec_data: 0xff >>> SPD index 7 >>> No memory dimm at address A0 >>> No memory dimm at address A2 >>> No memory dimm at address A6 >>> .... >>> 0 DIMMs found >>> .... >>> >>> ‐‐‐‐‐‐‐ Original Message ‐‐‐‐‐‐‐ >>> On Wednesday, 12 September 2018 13:29, Jose Trujillo via coreboot >>> <coreboot@coreboot.org> wrote: >>> >>> Dear coreboot engineers: >>> >>> Right now I am stuck with a Kabylake system with the following message: >>> .... >>> CPU #1 initialized >>> apic_id: 0x06 done. >>> microcode: updated to revision 0x8d date=2018-01-21 >>> CPU #3 initialized >>> bsp_do_flight_plan done after 220 msecs. >>> CPU: frequency set to 3600 MHz >>> Enabling SMIs. >>> Locking SMM. >>> VMX : param.enable = 0 >>> VMX: pre-conditions not met >>> SGX: pre-conditions not met >>> VMX: pre-conditions not met >>> VMX: pre-conditions not met >>> SGX: pre-conditions not met >>> SGX: pre-conditions not met >>> VMX: pre-conditions not met >>> SGX: pre-conditions not met >>> POST: 0x71 >>> .... >>> >>> May be some configuration is missing and I am trying to find this out >>> myself but if someone of you can give a hint on how to resolve it I will be >>> grateful. >>> >>> Attached is the full serial dump. >>> >>> Thank you, >>> Jose Trujillo >>> >>> >>> >>> -- >>> coreboot mailing list: coreboot@coreboot.org >>> https://mail.coreboot.org/mailman/listinfo/coreboot >> >> >> >> -- >> Best regards, >> Naresh G. Solanki >> >> >> -- >> coreboot mailing list: coreboot@coreboot.org >> https://mail.coreboot.org/mailman/listinfo/coreboot > > > -- > coreboot mailing list: coreboot@coreboot.org > https://mail.coreboot.org/mailman/listinfo/coreboot -- Best regards, Naresh G. Solanki -- coreboot mailing list: coreboot@coreboot.org https://mail.coreboot.org/mailman/listinfo/coreboot