Hi
You have to set AHCI mode in the BIOS or the resources needed to use
it wont be available, so yes its software but not ours :)
-Søren
On 14Apr, 2008, at 17:31 , Dag-Erling Smørgrav wrote:
Søren Schmidt <[EMAIL PROTECTED]> writes:
They arent, unless your HW runs in legacy emulation mode, then some
chipsets emulates master/slave pairs.
Hmm, isn't that a matter of software more than hardware, i.e. the
driver
switches to "native" mode when FreeBSD boots?
Or perhaps I should double-check that the BIOS is set to "AHCI mode"?
The hardware is ICH8, except for the DVDR drive which is on a POS
JMicron controller:
[EMAIL PROTECTED] ~% grep \^ata /var/run/dmesg.boot
atapci0: <JMicron AHCI controller> mem 0xf9000000-0xf9001fff irq 17
at device 0.0 on pci4
atapci0: [ITHREAD]
atapci0: AHCI Version 01.00 controller with 2 ports detected
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
atapci1: <JMicron JMB363 UDMA133 controller> port
0xa000
-0xa007,0xa400-0xa403,0xa800-0xa807,0xac00-0xac03,0xb000-0xb00f irq
18 at device 0.1 on pci4
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
atapci2: <Intel ICH8 SATA300 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f,0xfc00-0xfc0f at
device 31.2 on pci0
ata0: <ATA channel 0> on atapci2
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci2
ata1: [ITHREAD]
atapci3: <Intel ICH8 SATA300 controller> port
0xd800
-0xd807,0xdc00-0xdc03,0xe000-0xe007,0xe400-0xe403,0xe800-0xe80f,
0xec00-0xec0f irq 19 at device 31.5 on pci0
atapci3: [ITHREAD]
ata5: <ATA channel 0> on atapci3
ata5: [ITHREAD]
ata6: <ATA channel 1> on atapci3
ata6: [ITHREAD]
[EMAIL PROTECTED] ~% sudo atacontrol list
ATA channel 0:
Master: ad0 <Maxtor 6B300S0/BANC1B10> Serial ATA v1.0
Slave: ad1 <WDC WD4000AAKS-00TMA0/12.01C01> Serial ATA II
ATA channel 1:
Master: ad2 <WDC WD5000AAKS-00YGA0/12.01C02> Serial ATA II
Slave: ad3 <WDC WD4000AAKS-00TMA0/12.01C01> Serial ATA II
ATA channel 2:
Master: no device present
Slave: no device present
ATA channel 3:
Master: no device present
Slave: no device present
ATA channel 4:
Master: acd0 <PLEXTOR DVDR PX-716AL/1.00> ATA/ATAPI revision 6
Slave: no device present
ATA channel 5:
Master: ad10 <WDC WD4000AAKS-00TMA0/12.01C01> Serial ATA II
Slave: no device present
ATA channel 6:
Master: ad12 <WDC WD5000AAKS-00TMA0/12.01C01> Serial ATA II
Slave: no device present
DES
--
Dag-Erling Smørgrav - [EMAIL PROTECTED]
_______________________________________________
cvs-all@freebsd.org mailing list
http://lists.freebsd.org/mailman/listinfo/cvs-all
To unsubscribe, send any mail to "[EMAIL PROTECTED]"
