Hi all, I am trying to get my Wireless Card working with MUSB DMA Mode enabled at full speed. The moment I insert Zydas modules the musb starts giving me following rx_reinit errors. (Without DMA Mode Enable, the driver works fine).
I observe the same problem while connecting the device in high speed mode also. Though enabling the DMA mode is working fine with my High Speed USB Disk. Any clues what could be going wrong here? Kernel 2.6.18 USB Wireless Adapter - Zydas 1211b ------------------ Console Snapshot --------------------- usbcore: registered new driver usbfs usbcore: registered new driver hub Starting Host Controller musb_hdrc: version 2.2a/db-0.5.1/dbg, cppi-dma, host, debug=3 musb_hdrc: USB Host mode controller at c5002000 using DMA, IRQ 12 musb_hdrc musb_hdrc: MUSB HDRC host driver musb_hdrc musb_hdrc: new USB bus registered, assigned bus number 1 usb usb1: Product: MUSB HDRC host driver usb usb1: Manufacturer: Linux 2.6.18 musb-hcd usb usb1: SerialNumber: musb_hdrc usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb 1-1: new full speed USB device using musb_hdrc and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected musb_ep_program 899: broken !rx_reinit, ep3 csr 3200 musb_ep_program 899: broken !rx_reinit, ep3 csr 3000 usb 1-1.2: new full speed USB device using musb_hdrc and address 3 usb 1-1.2: not running at top speed; connect to a high speed hub usb 1-1.2: Product: USB2.0 WLAN usb 1-1.2: Manufacturer: ZyDAS usb 1-1.2: configuration #1 chosen from 1 choice Starting Zydas ZD1211B - version 2.18.0.0 vendor_id = 0ace product_id = 1215 USB 1.1 Host Release Ver = 4810 EEPORM Ver = 4810 Finsih download Firmware. Ready to reboot musb_ep_program 899: broken !rx_reinit, ep4 csr 3200 musb_ep_program 899: broken !rx_reinit, ep4 csr 3000 musb_ep_program 899: broken !rx_reinit, ep4 csr 3200 musb_ep_program 899: broken !rx_reinit, ep4 csr 3000 PA type: 0 PHYNEWLayout = 1 Airoha AL2230S_RF musb_ep_program 899: broken !rx_reinit, ep4 csr 3200 musb_ep_program 899: broken !rx_reinit, ep4 csr 3000 musb_ep_program 899: broken !rx_reinit, ep4 csr 3200 musb_ep_program 899: broken !rx_reinit, ep4 csr 3000 musb_ep_program 899: broken !rx_reinit, ep4 csr 3200 AllowedChannel = 000107ff Region:16 musb_ep_program 899: broken !rx_reinit, ep4 csr 3000 musb_ep_program 899: broken !rx_reinit, ep4 csr 3200 ----------------------------------------------------------------------------------------- _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
