I have added the following lines in config file # MTD device name Device offset Env. size Flash sector size Number of sectors #/dev/mtd0 0x0000 0x4000 0x4000 #/dev/mtd1 0x4000 0x4000 0x4000 #/dev/mtd2 0x0000 0x4000 0x4000
#/dev/mtd0 0x0000 0x4000 0x4000 #/dev/mtd1 0x4000 0x4000 0x4000 # NAND example #/dev/mtd0 0x0000 0x4000 0x4000 2 #/dev/mtd1 0x4000 0x4000 0x4000 2 #/dev/mtd1 0x0000 0x140000 0x4000 50 /dev/mtd0 0x0000 0x20000 0x20000 Its giving " Segmentation fault" Thanks & Regards, Raghu Ramaraj -----Original Message----- From: Caglar Akyuz [mailto:[email protected]] Sent: Wednesday, August 25, 2010 5:22 PM To: [email protected] Cc: Raghu Ramaraj; Jose, Frangline Subject: Re: need help- fw_printenv& fw_setenv On Wednesday 25 August 2010 10:28:37 am Raghu Ramaraj wrote: > Hi, > We facing some issue while using fw_printenv and fw_setenv ( uboot > tools). Pls find the logs/steps below I have used linux 2.6.32 rc5 kernel > source. > > > 1) MTD partition in the kernel level > > Cat /proc/mtd > mtd0: 00020000 00004000 "params" > mtd1: 00140000 00004000 "bootloader" > mtd2: 00400000 00004000 "kernel" > mtd3: 03aa0000 00004000 "file system" > param & bootloader partitions are interchanged ? > > 2) Cat /dev/mtd0 ->its displaying param related information > > > 3) I have used /etc/fw_env.config file > > > /dev/mtd0 0x0000 0x4000 0x4000 > /dev/mtd1 0x4000 0x4000 0x4000 > This file is completely wrong for DM6467. I guess you copied the exact config from u-boot tree but this is for 2 NAND flashes with small page. Correct version should be: /dev/mtd0 0x0000 0x20000 0x20000 Assuming your page size is 2KiB. Regards, Caglar > > 4) If I do ./fw_printenv , I am getting the all the boot params > 5) If I do ./fw_setenv bootdelay , I am getting the following > Permission denied > > > Losg are.............. > > > [email protected]:/home/raghu/env# cat /proc/mtd > dev: size erasesize name > mtd0: 00020000 00004000 "params" > mtd1: 00140000 00004000 "bootloader" > mtd2: 00400000 00004000 "kernel" > mtd3: 03aa0000 00004000 "filesystem" > [email protected]:/home/raghu/env# cat /dev/mtd0 > uEÈbootdelay=3baudrate=115200bootfile="uImage"addclk=setenv bootargs > ${bootargs} clkref=${clkref}ethact=DaVinci > EMACfilesize=D9CB0Ffileaddr=87000000gatewayip=17 > 2.22.64.1netmask=255.255.240.0ipaddr=172.22.66.43bootcmd=ping > 192.168.1.1;nand r ead 0x84600000 0x4a0000 0x1400000;nboot 0x80700000 0 > 0xa0000;bootmserverip=172.2 > 2.75.253ethaddr=00:0e:99:02:b5:69clkref=33000000stdin=serialstdout=serials > tderr= serialver=U-Boot 2009.08 (Jul 10 2010 - > 11:44:06)bootargs=console=ttyS0,115200n8 noinitrd rw root=/dev/nfs > nfsroot=172.22.75.253:/opt/mv_pro_5.0/montavista/pro/ > devkit/arm/v5t_le/target/,nolock mem=80M eth=00:0e:99:02:b5:69 ip=dhcp0 - > 14:34: 54)0700000 0 0xa0000;bootm > [email protected]:/home/raghu/env# ./fw_printenv > ootdelay=3 > baudrate=115200 > bootfile="uImage" > addclk=setenv bootargs ${bootargs} clkref=${clkref} > ethact=DaVinci EMAC > filesize=D9CB0F > fileaddr=87000000 > gatewayip=172.22.64.1 > netmask=255.255.240.0 > ipaddr=172.22.66.43 > bootcmd=ping 192.168.1.1;nand read 0x84600000 0x4a0000 0x1400000;nboot > 0x8070000 0 0 0xa0000;bootm > serverip=172.22.75.253 > ethaddr=00:0e:99:02:b5:69 > clkref=33000000 > stdin=serial > stdout=serial > stderr=serial > ver=U-Boot 2009.08 (Jul 10 2010 - 11:44:06) > bootargs=console=ttyS0,115200n8 noinitrd rw root=/dev/nfs > nfsroot=172.22.75.253: > /opt/mv_pro_5.0/montavista/pro/devkit/arm/v5t_le/target/,nolock mem=80M > eth=00:0 e:99:02:b5:69 ip=dhcp > [email protected]:/home/raghu/env# ./fw_setenv bootdelay 0 > Can't open /dev/mtd1: Permission denied > Error: can't write fw_env to flash > [email protected]:/home/raghu/env# > > > > Thanks & Regards > Raghu Ramaraj > > ________________________________ > http://www.mindtree.com/email/disclaimer.html > _______________________________________________ Davinci-linux-open-source mailing list [email protected] http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
