Sekhar, On Mon, Feb 4, 2013 at 10:33 AM, Prabhakar Lad <prabhakar.cse...@gmail.com> wrote: > Sekhar , > > On Sun, Feb 3, 2013 at 6:15 PM, Sekhar Nori <nsek...@ti.com> wrote: >> On 1/28/2013 7:17 PM, Prabhakar Lad wrote: >>> From: Lad, Prabhakar <prabhakar....@ti.com> >>> >>> The system configuration chip CFGCHIP3, controls the emac module. >>> This patch appropriately configures this register for emac and >>> sets DA850_MII_MDIO_CLKEN_PIN GPIO pin appropriately. >>> >>> Signed-off-by: Lad, Prabhakar <prabhakar....@ti.com> >>> Cc: linux-arm-ker...@lists.infradead.org >>> Cc: linux-ker...@vger.kernel.org >>> Cc: davinci-linux-open-source@linux.davincidsp.com >>> Cc: net...@vger.kernel.org >>> Cc: devicetree-disc...@lists.ozlabs.org >>> Cc: Sekhar Nori <nsek...@ti.com> >>> Cc: Heiko Schocher <h...@denx.de> >>> --- >>> arch/arm/mach-davinci/da8xx-dt.c | 28 ++++++++++++++++++++++++++++ >>> 1 files changed, 28 insertions(+), 0 deletions(-) >>> >>> diff --git a/arch/arm/mach-davinci/da8xx-dt.c >>> b/arch/arm/mach-davinci/da8xx-dt.c >>> index e533a0a..4a096e3 100644 >>> --- a/arch/arm/mach-davinci/da8xx-dt.c >>> +++ b/arch/arm/mach-davinci/da8xx-dt.c >>> @@ -8,6 +8,7 @@ >>> * published by the Free Software Foundation. >>> */ >>> #include <linux/io.h> >>> +#include <linux/gpio.h> >>> #include <linux/of_irq.h> >>> #include <linux/of_platform.h> >>> #include <linux/irqdomain.h> >>> @@ -39,6 +40,32 @@ static void __init da8xx_init_irq(void) >>> >>> #ifdef CONFIG_ARCH_DAVINCI_DA850 >>> >>> +static void __init da8xx_config_emac(void) >>> +{ >>> +#define DA850_MII_MDIO_CLKEN_PIN GPIO_TO_PIN(2, 6) >>> +#define DA850_EMAC_MODE_SELECT BIT(8) >>> + void __iomem *cfg_chip3_base; >>> + int ret; >>> + u32 val; >>> + >>> + cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG); >>> + >>> + val = __raw_readl(cfg_chip3_base); >>> + val &= ~DA850_EMAC_MODE_SELECT; >>> + /* configure the CFGCHIP3 register for MII */ >>> + __raw_writel(val, cfg_chip3_base); >> >> Use readl/writel instead. >> > Ok. > >>> + pr_info("EMAC: MII PHY configured\n"); >>> + >>> + ret = gpio_request(DA850_MII_MDIO_CLKEN_PIN, "mdio_clk_en"); >>> + if (ret) { >>> + pr_warn("Cannot open GPIO %d\n", >>> + DA850_MII_MDIO_CLKEN_PIN); >>> + return; >>> + } >>> + /* Enable/Disable MII MDIO clock */ >>> + gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, 0); >>> +} >>> + >>> struct of_dev_auxdata da8xx_auxdata[] __initdata = { >>> OF_DEV_AUXDATA("ti,davinci_mdio", 0x01e24000, "davinci_mdio.0", NULL), >>> OF_DEV_AUXDATA("ti,davinci-dm6467-emac", 0x01e20000, "davinci_emac.1", >>> @@ -52,6 +79,7 @@ static void __init da850_init_machine(void) >>> da8xx_auxdata, NULL); >>> >>> da8xx_uart_clk_enable(); >>> + da8xx_config_emac(); >> >> There are couple of issues with this implementation. >> >> 1) da8xx_config_emac() is specific to DA850 EVM, but masquerades as >> generic for da8xx. Looks like you need two functions, one for soc >> specific configuration and one board specific. > Ok. > >> 2) da8xx_config_emac() goes through all the time, whether the >> particular board has emac module or not. Shouldn't >> da8xx_config_emac() check if emac is actually enabled in the passed >> dtb and only the do the configuration? > > Ok. Can you give some pointers how we can access the dtb in board files. > Any pointers on this could be helpful.
Regards, --Prabhakar >> 3) The function assumes mii is used always, you can use the rmii_en dt >> property to check if rmii/mii is enabled and configure the soc/board >> accordingly. > > Ok. > >> 4) If the same function can work both for da850 and da830, then it can >> be implemented outside of CONFIG_ARCH_DAVINCI_DA850. >> > Ok. > > Regards, > --Prabhakar > >> Thanks, >> Sekhar _______________________________________________ Davinci-linux-open-source mailing list Davinci-linux-open-source@linux.davincidsp.com http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source