Lee Begg wrote: > On Wed, 09 Nov 2005 00:16, dclemen wrote: > >>More info: dmesg >> >>Bootdata ok (command line is root=/dev/sda3 ro console=tty0 ) > > <snip> > >>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 >>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx >>JFS: nTxBlock = 8013, nTxLock = 64111 >>Adding 1775172k swap on /dev/sda2. Priority:-1 extents:1 >>Probing IDE interface ide0... >>hda: TOSHIBA ODD-DVD SD-M1802, ATAPI CD/DVD-ROM drive >>Probing IDE interface ide1... >>hdc: HL-DT-ST DVDRAM GSA-4163B, ATAPI CD/DVD-ROM drive >>Probing IDE interface ide2... >>Probing IDE interface ide3... >>Probing IDE interface ide4... >>Probing IDE interface ide5... >>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 >>ide1 at 0x170-0x177,0x376 on irq 15 >>ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX >>as device > > > Since ide-scsi is not in your bootparams (the "command line" above), my guess > is that you have ide-scsi in /etc/modules. If you do, remove it. Then > reboot. > > If that isn't the case, did you compile your kernel? Maybe you turned ide-scsi > on? > > As of 2.6.0, noone should use ide-scsi (unless it doesn't work at all without > it). > > Hope this helps. > > Later > Lee Begg
No I don't compile kernel, I get it as .deb package (2.6.12-1). ide-scsi are not in /etc/modules, but it is loaded (restart system but loaded again). This is my modules file: $ cat /etc/modules # /etc/modules: kernel modules to load at boot time. # # This file should contain the names of kernel modules that are # to be loaded at boot time, one per line. Comments begin with # a "#", and everything on the line after them are ignored. ide-cd ide-disk ide-generic psmouse sd_mod When I try to remove this module I get this error # rmmod ide-scsi Terminado (killed) Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:32 2005 ... localhost kernel: Oops: 0000 [1] Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:32 2005 ... localhost kernel: CR2: 0000000000000370 Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:37 2005 ... localhost kernel: Oops: 0000 [2] Message from [EMAIL PROTECTED] at Tue Nov 8 14:29:37 2005 ... localhost kernel: CR2: 0000000000000370 And module are not removed: # lsmod | grep ide ide_generic 1600 0 [permanent] ide_disk 18048 0 ide_cd 43552 0 cdrom 39544 2 sr_mod,ide_cd ide_scsi 18116 0 ide_core 144888 5 amd74xx,ide_generic,ide_disk,ide_cd,ide_scsi scsi_mod 151512 5 sg,sr_mod,ide_scsi,sd_mod,libata Maybe as Dean Hamstead said, I have to rebuild initrd? (remove/rename /lib/modules/2.6.12-1-amd64-k8/kernel/drivers/scsi/ide-scsi.ko file, and mkinitrd?) Thanks for replies!!! (I boot with old 2.6.8 kernel and not load ide-scsi module, devices are hda and hdc and work fine) -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]