Has anyone had any luck using DI to install on a bast ?? I just tried the 20040820 DI rc1 install CD build, so far without success. I'm using a serial console, so used a variation of the ABLE commands given here:
http://www.simtec.co.uk/products/EB2410ITX/faq.html#faqquestion_45 (As an aside, the bast can load and run bootloader scripts directly from a local filesystem, so it would be nice to have the correct commands in a script somewhere on the DI install CD filesystem...). SuperIO controller fitted Initialising Detecting SDRAM size SDRAM: BANK6 size 04000000 SDRAM: BANK7 size 04000000 ABLE: 1.98 (bast,s3c2410x) ([EMAIL PROTECTED]) Wed Jun 2 00:07:42 BST 2004 System: Machine bast/s3c2410x, Linux id 0x014b Processor: Samsung S3C2410X (arm920) (0) S3C2410X RTC: 23:39:45, 20/08/2004 NAND: configured boot slot is 0 (card slot) EEPROM: 24cXX, 1024 bytes, single byte addressed (nvram0) on (24cxx) Setting CPU Speed to 203MHz no confiuration, defaulting to vga X/Y values invalid, configuring automatically Chrontel CH7006 detected screen mode is 640x480, ?Hz, ?Hz HSync video: video size 300K configuring ch7006: vga selected serial for console write stream selected serial for console read stream DRAM: 128 Mb (134217728 bytes) BAST: PMU version 1.02, ID 00:01:3d:00:01:04 ABLE: 1.98 (bast,s3c2410x) ([EMAIL PROTECTED]) Wed Jun 2 00:07:42 BST 2004 hda: ATAPI CDROM: Slimtype DVD-ROM LSD-081 (hda) 69MB (cd0) on ((hda1):iso9660) (rom0) on (nor0) DM9000: dm0: r0, 00:01:3d:00:01:04 int phy, link ok, 100Mbit half duplex NE2000: ne0: ISA/Generic, 00:01:3d:00:01:05 (EEPROM Invalid / Missing) sys.autoshadow unset, automatically shadowing boot.cmd unset, defaulting to '(cd0)install.sh' Autoboot in 8 seconds (attempt 1), Press any key to abort > >nvshow shell-hist (is unset) cons-write = serial cons-read = serial boot.auto (is unset) boot.cmd (is unset) boot.timeout = 8 ide.multi-limit (is unset) fb.enable (is unset) fb.output (is unset) fb.y (is unset) fb.x (is unset) sys.autoshadow (is unset) sys.speed = 203 > >setargs root=/dev/ram rw console=ttySAC0,115200 s3c2410fb_disable=yes >load (cd0)/install/bast/vmlinuz-2.4.25-bast (cd0)/install/bast/initrd.gz loaded (cd0)/install/bast/vmlinuz-2.4.25-bast, 0xfa69c bytes at 0x00008000 loaded (cd0)/install/bast/initrd.gz, 0x14dbe9 bytes at 0x00408000 > >boot boot: booting 'linux' Booting Linux Uncompressing Linux............................................... ........................... done, booting the kernel. (The early kernel messages seem to get garbled...) tts/AC%d%d0 at MMIO 0xd8800000 (irq = 70) is a S3C2410 tts/AC%d%d1 at MMIO 0xd8804000 (irq = 73) is a S3C2410 tts/AC%d%d2 at MMIO 0xd8808000 (irq = 76) is a S3C2410 S3C2410 LCD/VGA Console support Console: switching to colour frame buffer device 80x60 keyboard: Timeout - AT keyboard not present?(ed) keyboard: Timeout - AT keyboard not present?(f4) pty: 256 Unix98 ptys configured lp: driver loaded but no devices found Installing S3C2410 RTC S3C Real Time Clock driver v1.00 ppdev: user-space parallel port driver S3C2410 Watchdog Timer: timer margin 20 sec RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize bast-asix.c:v1.02 21/05/2003 D. Becker/P. Gortmaker/Ben Dooks http://www.simtec.co.uk/products/EB2410ITX/ net_bast_modinit: new device at c05dac00 bast-asix.c:v1.02 21/05/2003 D. Becker/P. Gortmaker/Ben Dooks http://www.simtec.co.uk/products/EB2410ITX/ BAST Onboard NE2000 driver, (c) 2003 Simtec Electronics eth0: bast-ne2k found at 0xee400000, IRQ 55, 00:02:04:06:08:0A. BAST DM9000 Ethernet Driver, (c) 2003 Simtec Electronics eth1: bast-dm9000 found at 0xea500000, IRQ 54, 00:02:04:06:08:0A. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx bast: IDE driver, (c) 2003 Simtec Electronics ide0: at ee000100 (ee100000) ide1: at ee200100 (ee300000) hda: Slimtype DVD-ROM LSD-081, ATAPI CD/DVD-ROM drive ide0 at 0xee000000-0xee000007,0xee1000c0 on irq 60 tlv320aic23: (c) 2003 Simtec Electronics IISCON=0000002c, IISMOD=00000189, IISFCON=0000a000 S3C2410: TLV320AIC23 / IIS initialized BAST Flash driver, (c) 2003 Simtec Electronics BAST flash mapped to c884d000 Search for id:(08 ea00) interleave(1) type(2) Search for id:(bf 2782) interleave(1) type(2) Found: SST 39LF160 BAST: Found 1 x16 devices at 0x0 in 16-bit mode number of JEDEC chips: 1 No RedBoot partition table detected in BAST BAST Flash: Using none partition definition Creating -1071493716 MTD partitions on "BAST": usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb: setting gbpcon=000a85aa usb: setting gbpdat=000002ef host/usb-ohci.c: USB OHCI at membase 0xd8200000, IRQ 42 usb.c: new USB bus registered, assigned bus number 1 Product: USB OHCI Root Hub SerialNumber: d8200000 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]> hid-core.c: USB HID support drivers usb.c: registered new driver usblp printer.c: v0.13: USB Printer Device Class driver usb.c: registered new driver usbnet usb.c: registered new driver serial usbserial.c: USB Serial Driver core v1.4 usbserial.c: USB Serial support registered for FTDI SIO usbserial.c: USB Serial support registered for FTDI 8U232AM Compatible usbserial.c: USB Serial support registered for FTDI FT232BM Compatible usbserial.c: USB Serial support registered for USB-UIRT Infrared Receiver/Transmitter usbserial.c: USB Serial support registered for Home-Electronics TIRA-1 IR Transceiver ftdi_sio.c: v1.3.5:USB FTDI Serial Converters Driver usbserial.c: USB Serial support registered for PL-2303 pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.10 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 1024 buckets, 8Kbytes TCP: Hash tables configured (established 8192 bind 8192) NetWinder Floating Point Emulator V0.97 (double precision) IrCOMM protocol (Dag Brattli) RAMDISK: Compressed image found at block 0 Freeing initrd memory: 1334K VFS: Mounted root (ext2 filesystem). Freeing init memory: 100K Setting up filesystem, please wait ... Then nothing more from the serial port. The VGA port manages a flickering Tux, but nothing more. -- _______________________________________________ Find what you are looking for with the Lycos Yellow Pages http://r.lycos.com/r/yp_emailfooter/http://yellowpages.lycos.com/default.asp?SRC=lycos10
