Package: installation-reports INSTALL REPORT
Debian-installer-version: RC1 Method: Business-Card i386 ISO of RC1, installing base over http/proxy Machine: IBM Thinkpad R51 Processor: Pentium M/1.5GHz Memory: 512MB Root Device: IC25N040ATMR04-0, ATA DISK drive Root Size/partition table: hda1 Primary Linux ext3 4999.94 (Debian GNU/Linux) hda5 Logical Linux ext2 1599.90 (Debian GNU/Hurd) hda9 Logical Linux ext3 1599.90 / hda6 Logical Linux ext3 27155.43 (data) hda7 Logical Linux swap 1023.94 swap hda8 Logical Linux ext2 3628.68 (data) Output of lspci and lspci -n: Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [ ] Reboot: [E] Comments/Problems: 1. It was previously suggested to rename the inital boot dialog, like s/press Return to boot/press Return to install Debian/ or something 2. If I don't have a network cable plugged in, I get asked for an IP address. It's possible to go back and then select 'No network configuration' (or something), but having a button like 'Continue without configuring the network' right there intially would be better. Though that's probably i) not easy with debconf and ii) too late for sarge anyway 3. As it wasn't immediatly obvious how to reformat a partition with partman, I (perhaps foolishly) decided to delete and re-create /dev/hda6 (on which some other ext2 previously existed). However, the format dialog and subsequent dialogs talked about /dev/hda9 being created/written to, which made me a bit nervous. I finally figured out that partman renumbered the devices (see above partition listing), adding /dev/hda9 at the place of the former /dev/hda6 but calling it /dev/hda9. Oh well, that was a bit unsuspected and I had to change the /etc/fstab of my other partition to fix it. If it is possible the partition numbering should be preserved IMHO. 4. I did not install Grub so I can't tell whether my GNU/Hurd partition has been detected and included correctly, but I could test that another time if needed. 5. On reboot, during the bootup sequence, the framebuffer switched to a different font which yielded about twice as many lines on the console (to my liking). However, as soon as base-config started (or perhaps shortly before), the console became totally corrupted and scrambled. It was possible to figure out that I was looking at the base-config screen and changing virtual consoles worked, but I was not able to read anything. This was with the default 2.4 kernel. I later reinstalled passing 'kernel26' to d-i, which worked fine (though the console font stayed at the intial size/number of lines) 6. I did not select any tasks in tasksel but rather did 'apt-get install gnome' from the console (I don't like how both KDE and GNOME get installed by the desktop task, but oh well). I also installed x-window-system-core and before that discover, mdetect, read-edid. Configuring X was mostly alright and I noticed that the synaptic touchpad driver got loaded during it at one point. However, after reboot, the driver did not get loaded and X failed to come up. I had to manually add psmouse to /etc/modules. That's about it. Needless to say I'm pretty proud of y'all :) Michael Install logs and other status info is available in /var/log/debian-installer/. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]