Package: installation-reports INSTALL REPORT
Debian-installer-version: sarge-i386-businesscard.iso uname -a: Linux up1 2.6.7-1-686 #1 Thu Jul 8 05:36:53 EDT 2004 i686 GNU/Linux Date: Wed Sep 1 14:30:00 EDT 2004 Method: Installed from business card iso over the net from ftp.debian.org with no proxies. Machine: IBM BladeCenter HS20 8832 Processor: 2 x 3.2 GHz Intel Xeon Memory: 4 GB Root Device: SCSI (LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI) Root Size/partition table: --partition table-- Disk /dev/sda: 146.6 GB, 146693685248 bytes 255 heads, 63 sectors/track, 17834 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System Mounts /dev/sda1 * 1 18 144553+ 83 Linux / /dev/sda2 19 17834 143107020 5 Extended /dev/sda5 19 626 4883728+ 83 Linux /usr /dev/sda6 627 991 2931831 83 Linux /tmp /dev/sda7 992 1040 393561 83 Linux /var /dev/sda8 1041 17772 134399758+ 83 Linux /home /dev/sda9 17773 17834 497983+ 82 Linux swap swap --partition table-- Output of lspci and lspci -n: --lspci output-- 0000:00:00.0 Host bridge: ServerWorks CMIC-LE Host Bridge (GC-LE chipset) (rev 33) 0000:00:00.1 Host bridge: ServerWorks CMIC-LE Host Bridge (GC-LE chipset) 0000:00:00.2 Host bridge: ServerWorks CMIC-LE Host Bridge (GC-LE chipset) 0000:00:01.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27) 0000:00:0f.0 Host bridge: ServerWorks CSB6 South Bridge (rev b0) 0000:00:0f.1 IDE interface: ServerWorks CSB6 RAID/IDE Controller (rev b0) 0000:00:0f.2 USB Controller: ServerWorks CSB6 OHCI USB Controller (rev 05) 0000:00:0f.3 ISA bridge: ServerWorks GCLE-2 Host Bridge 0000:00:10.0 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit Ethernet (rev 12) 0000:00:10.2 Host bridge: ServerWorks CIOB-E I/O Bridge with Gigabit Ethernet (rev 12) 0000:00:11.0 Host bridge: ServerWorks CIOB-X2 PCI-X I/O Bridge (rev 03) 0000:00:11.2 Host bridge: ServerWorks CIOB-X2 PCI-X I/O Bridge (rev 03) 0000:01:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5704S Gigabit Ethernet (rev 02) 0000:01:00.1 Ethernet controller: Broadcom Corporation NetXtreme BCM5704S Gigabit Ethernet (rev 02) 0000:03:01.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07) --lspci output-- --lspci -n output-- 0000:00:00.0 0600: 1166:0014 (rev 33) 0000:00:00.1 0600: 1166:0014 0000:00:00.2 0600: 1166:0014 0000:00:01.0 0300: 1002:4752 (rev 27) 0000:00:0f.0 0600: 1166:0203 (rev b0) 0000:00:0f.1 0101: 1166:0213 (rev b0) 0000:00:0f.2 0c03: 1166:0221 (rev 05) 0000:00:0f.3 0601: 1166:0227 0000:00:10.0 0600: 1166:0110 (rev 12) 0000:00:10.2 0600: 1166:0110 (rev 12) 0000:00:11.0 0600: 1166:0101 (rev 03) 0000:00:11.2 0600: 1166:0101 (rev 03) 0000:01:00.0 0200: 14e4:16a8 (rev 02) 0000:01:00.1 0200: 14e4:16a8 (rev 02) 0000:03:01.0 0100: 1000:0030 (rev 07) --lspci -n output-- Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [E] Comments/Problems: The install went as flawlessly as on the IDE install I did earlier. The issue I ran into upon rebooting was due to the installer being given the SCSI device as /dev/sdb during installation but it reverting to /dev/sda on boot (due to the CD-Rom apparently) causing a kernel panic since it couldn't find root. An easy fix was to edit /boot/grub/menu.lst and change the reference to /dev/sdb1 to /dev/sda1 (either before rebooting the first time or at the Grub menu.) Also, an edit to /etc/fstab is required. Other than that, an easy install and all hardware was recognized both during installation as well as afterwards. Thanks again, --asg -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]