Package: installation-reports Boot method: di3 full(non-netboot) CD Image version: Aprox 3rd Sep via jigdo Date: 10-Sep-2006
Machine: Processor: Athlon 1600+ Memory: 516672 kB Partitions: /dev/hdb6 ext3 9614116 1174616 7951128 13% / tmpfs tmpfs 258336 0 258336 0% /dev/shm tmpfs tmpfs 10240 148 10092 2% /dev /dev/hdc iso9660 658938 658938 0 100% /media/cdrom0 Output of lspci and lspci -n: 00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333] 00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP] 00:0d.0 Ethernet controller: Lite-On Communications Inc LNE100TX (rev 20) 00:0e.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10) 00:0f.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11) 00:0f.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11) 00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge 00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) 00:11.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) 00:11.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) 00:11.4 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 1b) 01:00.0 VGA compatible controller: nVidia Corporation NV15DDR [GeForce2 Ti] (rev a4) lspci -n 00:00.0 0600: 1106:3099 00:01.0 0604: 1106:b099 00:0d.0 0200: 11ad:0002 (rev 20) 00:0e.0 0401: 13f6:0111 (rev 10) 00:0f.0 0400: 109e:036e (rev 11) 00:0f.1 0480: 109e:0878 (rev 11) 00:11.0 0601: 1106:3074 00:11.1 0101: 1106:0571 (rev 06) 00:11.2 0c03: 1106:3038 (rev 1b) 00:11.3 0c03: 1106:3038 (rev 1b) 00:11.4 0c03: 1106:3038 (rev 1b) 01:00.0 0300: 10de:0151 (rev a4) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [O] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [E] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: Installed with expertgui. The only issues I noticed were with partitioning the disks (manual partitioning). I created two logical partitions on hdb. hdb6=ext3 / and hdb7=swap created in that order Writing changes showed this: The following partitions are going to be formatted: partition #6 of IDE1 master (hda) as swap partition #6 of IDE1 slave (hdb) as ext3 partition #7 of IDE1 slave (hdb) as swap. Now technically this is accurate, there is a swap partition on hda6 from my sarge install. However that partition was not referenced or modified by me in any way. I guess formatting it again won't do any harm but on the other hand why is the installer deciding to format other partitions? Also the interface for partitioning (partition list) was a little inconsistent in that it was the only screen which did not allow me to select items with the mouse. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]