--- Begin Message ---
Package: installation-reports
Version: 2.23
Severity: important
-- Package-specific info:
Boot method: network
Image version:
http://people.debian.org/~stappers/d-i/images/daily/sparc64/netboot/2.6/boot.img
build 27/Nov/2006
Date: <Date and time of the install>
Machine: Sun Netra X1
Partitions: <df -Tl will do; the raw partition table is preferred>
pingu:~# fdisk -l /dev/hda
Disk /dev/hda (Sun disk label): 16 heads, 63 sectors, 39691 cylinders
Units = cylinders of 1008 * 512 bytes
Device Flag Start End Blocks Id System
/dev/hda1 0 992 499968 1 Boot
~/dev/hda2 992 20368 9765504 83 Linux native
/dev/hda3 0 39693 20005272 5 Whole disk
/dev/hda4 20368 22306 976752 82 Linux swap
/dev/hda5 22306 24290 999936 1 Boot
/dev/hda6 24290 26274 999936 83 Linux native
/dev/hda7 26274 32983 3381336 83 Linux native
/dev/hda8 32983 39693 3381840 83 Linux native
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot: [O]
Detect network card: [E]
Configure network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Install base system: [O]
Clock/timezone setup: [O]
User/password setup: [O]
Install tasks: [O]
Install boot loader: [O]
Overall install: [O]
Comments/Problems:
The install went well apart from the loading of the wrong driver for the
onboard network devices DM9102 devices. The installer said that it was
loading the Tulip driver but also loaded the dmfe driver prior to it. The
dmfe driver "ate" the devices and Tulip found nothing to probe. This is a
problem because dmfe does not work with the onboard devices - it gives
lots of PCI bus errors and does not actually transfer traffic.
I was able to drop down to a shell and unload both dmfe and tulip with
modprobe -r and then reload tulip only. At this stage the networks setup
just fine.
Note the same problem arose during the reboot after installation.
FYI this machine/model is not capable of booting from a CD drive so it
is vital that network devices get loaded properly during install.
Here are a few bits of relevant output from the system.
Devices being loaded...
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
eth0: Davicom DM9102 at pci0000:00:05.0, 00:00:00:00:00:00, irq 7418560.
eth1: Davicom DM9102 at pci0000:00:0c.0, 00:00:00:00:00:00, irq 7417856.
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
ohci_hcd 0000:00:0a.0: OHCI Host Controller
We get a similar thing in the output during the post install boot
ALI15X3: 100% native mode on irq 5,7cc
ide0: BM-DMA at 0x1fe02010220-0x1fe02010227, BIOS settings: hda:DMA,
hdb:pio ide1: BM-DMA at 0x1fe02010228-0x1fe0201022f, BIOS settings: hdc:pio,
hdd:piodmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
hda: ST320423A, ATA DISK drive
ide0 at 0x1fe02010200-0x1fe02010207,0x1fe0201020a on irq 5,7cc
hdc: ST320423A, ATA DISK drive
ide1 at 0x1fe02010210-0x1fe02010217,0x1fe0201020e on irq 5,7cc
eth0: Davicom DM9102 at pci0000:00:05.0, 00:00:00:00:00:00, irq 7418560.
eth1: Davicom DM9102 at pci0000:00:0c.0, 00:00:00:00:00:00, irq 7417856.
Linux Tulip driver version 1.1.13-NAPI (May 11, 2002)
hda: max request size: 128KiB
--
Please make sure that the hardware-summary log file, and any other
installation logs that you think would be useful are attached to this
report.
Once you have filled out this report, mail it to [EMAIL PROTECTED]
==============================================
Installer lsb-release:
==============================================
DISTRIB_ID=Debian
DISTRIB_DESCRIPTION="Debian GNU/Linux installer"
DISTRIB_RELEASE="4.0 (installer build 20061127-12:05)"
X_INSTALLATION_MEDIUM=netboot-2.6
==============================================
Installer hardware-summary:
==============================================
umame -a: Linux pingu 2.6.17-2-sparc64 #1 Wed Sep 13 10:39:24 PDT 2006 sparc64
unknown
lspci -nn: 00:00.0 Host bridge [0600]: Sun Microsystems Computer Corp. Ultra
IIe [108e:a001]
lspci -nn: 00:03.0 Non-VGA unclassified device [0000]: ALi Corporation M7101
Power Management Controller [PMU] [10b9:7101]
lspci -nn: 00:05.0 Ethernet controller [0200]: Davicom Semiconductor, Inc.
21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31)
lspci -nn: 00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA
Bridge [Aladdin IV/V/V+] [10b9:1533]
lspci -nn: 00:0a.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03)
lspci -nn: 00:0c.0 Ethernet controller [0200]: Davicom Semiconductor, Inc.
21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31)
lspci -nn: 00:0d.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229]
(rev c3)
lspci -vnn: 00:00.0 Host bridge [0600]: Sun Microsystems Computer Corp. Ultra
IIe [108e:a001]
lspci -vnn: Flags: bus master, 66MHz, medium devsel, latency 40
lspci -vnn:
lspci -vnn: 00:03.0 Non-VGA unclassified device [0000]: ALi Corporation M7101
Power Management Controller [PMU] [10b9:7101]
lspci -vnn: Flags: medium devsel
lspci -vnn:
lspci -vnn: 00:05.0 Ethernet controller [0200]: Davicom Semiconductor, Inc.
21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31)
lspci -vnn: Flags: bus master, medium devsel, latency 160, IRQ 7418560
lspci -vnn: I/O ports at 1fe02010100 [size=256]
lspci -vnn: Memory at 1ff00002000 (32-bit, non-prefetchable) [size=256]
lspci -vnn: Expansion ROM at 1ff00100000 [disabled] [size=256K]
lspci -vnn: Capabilities: [50] Power Management version 1
lspci -vnn:
lspci -vnn: 00:07.0 ISA bridge [0601]: ALi Corporation M1533/M1535 PCI to ISA
Bridge [Aladdin IV/V/V+] [10b9:1533]
lspci -vnn: Subsystem: ALi Corporation M1533/M1535 PCI to ISA Bridge
[Aladdin IV/V/V+] [10b9:1533]
lspci -vnn: Flags: bus master, medium devsel, latency 0
lspci -vnn: Capabilities: [a0] Power Management version 1
lspci -vnn:
lspci -vnn: 00:0a.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller
[10b9:5237] (rev 03) (prog-if 10)
lspci -vnn: Flags: bus master, medium devsel, latency 32, IRQ 7418816
lspci -vnn: Memory at 1ff01000000 (32-bit, non-prefetchable) [size=4K]
lspci -vnn: Capabilities: [60] Power Management version 2
lspci -vnn:
lspci -vnn: 00:0c.0 Ethernet controller [0200]: Davicom Semiconductor, Inc.
21x4x DEC-Tulip compatible 10/100 Ethernet [1282:9102] (rev 31)
lspci -vnn: Flags: bus master, medium devsel, latency 160, IRQ 7417856
lspci -vnn: I/O ports at 1fe02010000 [size=256]
lspci -vnn: [virtual] Memory at 1ff00000000 (32-bit, non-prefetchable)
[size=256]
lspci -vnn: Expansion ROM at 1ff00040000 [disabled] [size=256K]
lspci -vnn: Capabilities: [50] Power Management version 1
lspci -vnn:
lspci -vnn: 00:0d.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229]
(rev c3) (prog-if ff)
lspci -vnn: Flags: bus master, medium devsel, latency 16, IRQ 7418048
lspci -vnn: I/O ports at 1fe02010200 [size=8]
lspci -vnn: I/O ports at 1fe02010208 [size=4]
lspci -vnn: I/O ports at 1fe02010210 [size=8]
lspci -vnn: I/O ports at 1fe0201020c [size=4]
lspci -vnn: I/O ports at 1fe02010220 [size=16]
lspci -vnn: Capabilities: [60] Power Management version 2
lspci -vnn:
lsmod: Module Size Used by
lsmod: xfs 483216 0
lsmod: reiserfs 312448 0
lsmod: jfs 195440 0
lsmod: ext3 151248 3
lsmod: jbd 58344 1 ext3
lsmod: vfat 14464 0
lsmod: fat 56304 1 vfat
lsmod: isofs 44464 0
lsmod: ide_cd 45128 0
lsmod: cdrom 41064 1 ide_cd
lsmod: ide_generic 1664 0 [permanent]
lsmod: cmd64x 12152 0 [permanent]
lsmod: cs5520 5632 0 [permanent]
lsmod: cs5530 6080 0 [permanent]
lsmod: cy82c693 5384 0 [permanent]
lsmod: it821x 9540 0 [permanent]
lsmod: ns87415 5100 0 [permanent]
lsmod: pdc202xx_new 9984 0 [permanent]
lsmod: pdc202xx_old 11648 0 [permanent]
lsmod: serverworks 10512 0 [permanent]
lsmod: siimage 12864 0 [permanent]
lsmod: trm290 5250 0 [permanent]
lsmod: via82cxxx 10372 0 [permanent]
lsmod: ide_disk 17536 5
lsmod: generic 5892 0 [permanent]
lsmod: alim15x3 13336 0 [permanent]
lsmod: tulip 53832 0
lsmod: ohci_hcd 19588 0
df: Filesystem 1k-blocks Used Available Use% Mounted on
df: tmpfs 257376 912 256464 0% /dev
df: tmpfs 257376 912 256464 0% /dev
df: tmpfs 257376 912 256464 0% /.dev
df: /dev/ide/host0/bus0/target0/lun0/part7 3328136 603544 2555528 19%
/target
df: /dev/ide/host0/bus0/target0/lun0/part5 984184 24520 909668 3%
/target/boot
df: /dev/ide/host0/bus0/target0/lun0/part8 3328640 1928424 1231124 61%
/target/home
free: total used free shared buffers
free: Mem: 514752 423464 91288 0 27928
free: Swap: 976736 912 975824
free: Total: 1491488 424376 1067112
cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 28: pccardctl: not found
cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 29: pccardctl: not found
cardctl status: /usr/bin/report-hw: /usr/bin/report-hw: 30: cardctl: not found
cardctl ident: /usr/bin/report-hw: /usr/bin/report-hw: 31: cardctl: not found
/proc/cpuinfo: cpu : TI UltraSparc IIe (Hummingbird)
/proc/cpuinfo: fpu : UltraSparc IIe integrated FPU
/proc/cpuinfo: prom : OBP 4.0.9 2001/05/17 21:52
/proc/cpuinfo: type : sun4u
/proc/cpuinfo: ncpus probed : 1
/proc/cpuinfo: ncpus active : 1
/proc/cpuinfo: D$ parity tl1 : 0
/proc/cpuinfo: I$ parity tl1 : 0
/proc/cpuinfo: Cpu0Bogo : 11.12
/proc/cpuinfo: Cpu0ClkTck : 0000000017d78400
/proc/cpuinfo: MMU Type : Spitfire
/proc/ioports: 1fe02000000-1fe02ffffff : SABRE0 PBMA
/proc/ioports: 1fe02000070-1fe02000071 : rtc
/proc/ioports: 1fe020002e8-1fe020002ef : serial
/proc/ioports: 1fe020003f8-1fe020003ff : serial
/proc/ioports: 1fe02002000-1fe0200203f : 0000:00:03.0
/proc/ioports: 1fe02004000-1fe0200401f : 0000:00:03.0
/proc/ioports: 1fe02008010-1fe02008011 : SUNW,lomh
/proc/ioports: 1fe02010000-1fe020100ff : 0000:00:0c.0
/proc/ioports: 1fe02010000-1fe020100ff : tulip
/proc/ioports: 1fe02010100-1fe020101ff : 0000:00:05.0
/proc/ioports: 1fe02010100-1fe020101ff : tulip
/proc/ioports: 1fe02010200-1fe02010207 : 0000:00:0d.0
/proc/ioports: 1fe02010200-1fe02010207 : ide0
/proc/ioports: 1fe02010208-1fe0201020b : 0000:00:0d.0
/proc/ioports: 1fe0201020a-1fe0201020a : ide0
/proc/ioports: 1fe0201020c-1fe0201020f : 0000:00:0d.0
/proc/ioports: 1fe0201020e-1fe0201020e : ide1
/proc/ioports: 1fe02010210-1fe02010217 : 0000:00:0d.0
/proc/ioports: 1fe02010210-1fe02010217 : ide1
/proc/ioports: 1fe02010220-1fe0201022f : 0000:00:0d.0
/proc/ioports: 1fe02010220-1fe02010227 : ide0
/proc/ioports: 1fe02010228-1fe0201022f : ide1
/proc/iomem: 1ff00000000-1ff5fffffff : SABRE0 PBMA
/proc/iomem: 1ff00000000-1ff000000ff : 0000:00:0c.0
/proc/iomem: 1ff00000000-1ff000000ff : tulip
/proc/iomem: 1ff00002000-1ff000020ff : 0000:00:05.0
/proc/iomem: 1ff00002000-1ff000020ff : tulip
/proc/iomem: 1ff00040000-1ff0007ffff : 0000:00:0c.0
/proc/iomem: 1ff000a0000-1ff000bffff : Video RAM area
/proc/iomem: 1ff000c0000-1ff000c7fff : Video ROM
/proc/iomem: 1ff000f0000-1ff000fffff : System ROM
/proc/iomem: 1ff00100000-1ff0013ffff : 0000:00:05.0
/proc/iomem: 1ff01000000-1ff01000fff : 0000:00:0a.0
/proc/iomem: 1ff01000000-1ff01000fff : ohci_hcd
/proc/interrupts: 0: 1938325 timer:dead
/proc/interrupts: 5: 41140 ide0:7cc, ide1:7cc
/proc/interrupts: 6: 206915 eth1:7c6
/proc/interrupts: 12: 33538 su(serial):7eb
/proc/interrupts: 14: 0 ohci_hcd:usb1:7e4
/proc/interrupts: 15: 2 SABRE UE:7ee, SABRE CE:7ef, SABRE
PCIERR:7f0, power:7e5
/proc/meminfo: MemTotal: 514752 kB
/proc/meminfo: MemFree: 91272 kB
/proc/meminfo: Buffers: 27928 kB
/proc/meminfo: Cached: 329120 kB
/proc/meminfo: SwapCached: 296 kB
/proc/meminfo: Active: 206064 kB
/proc/meminfo: Inactive: 166456 kB
/proc/meminfo: HighTotal: 0 kB
/proc/meminfo: HighFree: 0 kB
/proc/meminfo: LowTotal: 514752 kB
/proc/meminfo: LowFree: 91272 kB
/proc/meminfo: SwapTotal: 976736 kB
/proc/meminfo: SwapFree: 975824 kB
/proc/meminfo: Dirty: 584 kB
/proc/meminfo: Writeback: 0 kB
/proc/meminfo: Mapped: 17128 kB
/proc/meminfo: Slab: 45336 kB
/proc/meminfo: CommitLimit: 1234112 kB
/proc/meminfo: Committed_AS: 20800 kB
/proc/meminfo: PageTables: 432 kB
/proc/meminfo: VmallocTotal: 4194304 kB
/proc/meminfo: VmallocUsed: 1800 kB
/proc/meminfo: VmallocChunk: 4192504 kB
dmidecode: /usr/bin/report-hw: /usr/bin/report-hw: 39: dmidecode: not found
==============================================
Installer status:
==============================================
Package: preseed-common
Status: install ok unpacked
Version: 1.21
Depends: cdebconf-udeb, di-utils (>= 1.14)
Description: common files for preseeding
Package: udpkg
Status: install ok unpacked
Version: 1.04
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.41)
Description: tiny dpkg clone
Package: localechooser
Status: install ok installed
Version: 1.30
Depends: cdebconf-udeb, iso-3166-udeb, di-utils (>= 1.15)
Description: choose language/country/locale
Installer-Menu-Item: 10
Package: libnss-dns-udeb
Status: install ok unpacked
Version: 2.3.6.ds1-8
Description: GNU C Library: NSS helper for DNS - udeb
Package: download-installer
Status: install ok installed
Version: 1.12
Depends: cdebconf-udeb, net-retriever, anna (>= 1.07)
Description: Download installer components
Installer-Menu-Item: 23
Package: lowmemcheck
Status: install ok unpacked
Version: 1.22
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03)
Description: detect low-memory systems and enter lowmem mode
Package: main-menu
Status: install ok unpacked
Version: 1.15
Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb
(>= 0.45), cdebconf-udeb
Description: Debian installer main menu
Package: di-utils-shell
Status: install ok installed
Version: 1.41
Depends: cdebconf-udeb, di-utils (>= 1.18)
Description: Execute a shell
Installer-Menu-Item: 950
Package: di-utils
Status: install ok installed
Version: 1.41
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.47), cdebconf-udeb
Description: Miscellaneous utilities for the debian installer
Package: choose-mirror
Status: install ok installed
Version: 2.08
Depends: configured-network, choose-mirror-bin
Description: Choose mirror to install from (menu item)
Installer-Menu-Item: 23
Package: network-preseed
Status: install ok unpacked
Version: 1.21
Depends: cdebconf-udeb, configured-network, preseed-common
Description: download debconf preseed file
Installer-Menu-Item: 21
Package: cdebconf-newt-udeb
Status: install ok unpacked
Version: 0.109
Depends: cdebconf-udeb, di-utils-terminfo, libc6 (>= 2.3.5-1), libnewt0.52
Description: Newt frontend for Debian Configuration Management System
Package: module-init-tools-udeb
Status: install ok unpacked
Version: 3.3-pre3-1
Depends: libc6 (>= 2.3.5-1)
Description: tools for managing Linux kernel modules
Package: rootskel
Status: install ok installed
Version: 1.45
Depends: di-utils (>= 1.24), cdebconf-udeb
Description: Skeleton root filesystem used by debian-installer
Package: udev-udeb
Status: install ok unpacked
Version: 0.103-1
Depends: libc6 (>= 2.3.5-1)
Description: /dev/ and hotplug management daemon
Package: libfribidi0-udeb
Status: install ok unpacked
Version: 0.10.7-4
Depends: libc6 (>= 2.3.5-1)
Description: Free Implementation of the Unicode BiDi algorithm
Package: nic-modules-2.6.17-2-sparc64-di
Status: install ok unpacked
Version: 1.14
Provides: nic-modules
Depends: kernel-image-2.6.17-2-sparc64-di
Description: Network card modules for Sparc kernels
Package: libtextwrap1-udeb
Status: install ok installed
Version: 0.1-5
Depends: libc6 (>= 2.3.5-1)
Description: text-wrapping library with i18n - runtime udeb
Package: auto-install
Status: install ok unpacked
Version: 0.02
Depends: netcfg, preseed-common (>= 1.18)
Description: Support for automatic installs
Installer-Menu-Item: 19
Package: usb-discover
Status: install ok unpacked
Version: 1.06
Depends: cdebconf-udeb
Description: Discover USB and load kernel modules
Package: rescue-check
Status: install ok unpacked
Version: 1.7
Depends: cdebconf-udeb (>= 0.75), main-menu (>= 1.03), di-utils (>= 1.18)
Description: enter d-i rescue mode if requested
Package: nano-udeb
Status: install ok unpacked
Version: 2.0.1-1
Provides: editor
Depends: libc6 (>= 2.3.5-1), libslang2-udeb (>= 2.0.6-3)
Description: free Pico clone with some new features - tiny build
Package: cdebconf-udeb
Status: install ok installed
Version: 0.109
Provides: debconf-2.0
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.45),
libtextwrap1-udeb
Description: Debian Configuration Management System (C-implementation)
Package: ai-choosers
Status: install ok unpacked
Version: 0.02
Depends: kbd-chooser (>= 1.30), localechooser (>= 1.23)
Description: Delayed configuration of locale and keyboard for auto-install
Installer-Menu-Item: 22
Package: libiw28-udeb
Status: install ok installed
Version: 28-1
Depends: libc6 (>= 2.3.5-1)
Description: Tools for manipulating Linux Wireless Extensions
Package: cdebconf-text-udeb
Status: install ok unpacked
Version: 0.109
Depends: cdebconf-udeb, libc6 (>= 2.3.5-1)
Description: Plain text frontend for Debian Configuration Management System
Package: iso-3166-udeb
Status: install ok installed
Version: 0.58-1
Description: provides iso_3166.tab file
Package: ethdetect
Status: install ok installed
Version: 1.43
Provides: ethernet-card-detection
Depends: rootskel (>= 1.30), cdebconf-udeb (>= 0.38), hw-detect, di-utils (>=
1.13)
Description: Detect network hardware and load kernel drivers for it
Installer-Menu-Item: 18
Package: busybox-udeb
Status: install ok unpacked
Version: 1:1.1.3-3
Depends: libc6 (>= 2.3.5-1)
Description: Tiny utilities for the debian-installer
Package: initrd-preseed
Status: install ok unpacked
Version: 1.21
Depends: preseed-common
Description: load debconf preseed file from /preseed.cfg on the initrd
Package: net-retriever
Status: install ok installed
Version: 1.12
Provides: retriever
Depends: cdebconf-udeb, choose-mirror, configured-network, di-utils (>= 1.16)
Description: Fetch modules from the Internet
Package: usb-modules-2.6.17-2-sparc64-di
Status: install ok unpacked
Version: 1.14
Provides: usb-modules
Depends: kernel-image-2.6.17-2-sparc64-di
Description: USB support
Package: archdetect
Status: install ok installed
Version: 1.43
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.45)
Description: Hardware architecture detector
Package: save-logs
Status: install ok unpacked
Version: 2.23
Depends: cdebconf-udeb
Description: save logs and configuration for debug purposes
Installer-Menu-Item: 940
Package: di-utils-reboot
Status: install ok unpacked
Version: 1.41
Depends: cdebconf-udeb
Description: Reboot
Installer-Menu-Item: 995
Package: anna
Status: install ok installed
Version: 1.25
Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb
(>= 0.45), cdebconf-udeb
Description: anna's not nearly apt, but for the Debian installer, it will do
Package: choose-mirror-bin
Status: install ok installed
Version: 2.08
Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb
(>= 0.45), cdebconf-udeb
Description: Choose mirror to install from (program)
Package: pciutils-udeb
Status: install ok unpacked
Version: 1:2.2.4-1
Depends: libc6 (>= 2.3.5-1), zlib1g-udeb (>= 1:1.2.1)
Description: Linux PCI Utilities (udeb)
Package: console-keymaps-at
Status: install ok installed
Version: 2:1.01-2
Provides: console-keymaps
Depends: cdebconf-udeb
Description: Keymaps for PC-style (PS/2 and AT) keyboards
Package: di-utils-terminfo
Status: install ok unpacked
Version: 1.41
Description: Terminfo entries needed by newt/slang in debian installer
Package: sparc-utils-udeb
Status: install ok unpacked
Version: 1.9-3
Depends: libc6 (>= 2.3.5-1)
Description: sparc-utils package for the Debian installer
Package: hw-detect
Status: install ok installed
Version: 1.43
Depends: rootskel (>= 1.30), archdetect, cdebconf-udeb (>= 0.75), di-utils (>=
1.26)
Description: Detect hardware and load kernel drivers for it
Package: kbd-chooser
Status: install ok installed
Version: 1.31
Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb
(>= 0.45), cdebconf-udeb, console-keymaps
Description: Detect a keyboard and select layout
Installer-Menu-Item: 12
Package: libdebian-installer4-udeb
Status: install ok installed
Version: 0.47
Depends: libc6 (>= 2.3.5-1)
Description: Library of common debian-installer functions
Package: kernel-image-2.6.17-2-sparc64-di
Status: install ok unpacked
Version: 1.14
Provides: kernel-image, ext2-modules
Description: Linux kernel binary image for the Debian installer
Package: installation-locale
Status: install ok unpacked
Version: 1.1
Depends: rootskel
Description: UTF-8 C locale
Package: env-preseed
Status: install ok unpacked
Version: 1.21
Description: debconf preseeding via environment variables
Package: cdebconf-priority
Status: install ok unpacked
Version: 0.109
Depends: cdebconf-udeb
Description: Change debconf priority
Installer-Menu-Item: 930
Package: netcfg
Status: install ok installed
Version: 1.31
Provides: configured-network
Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb
(>= 0.45), libiw28-udeb (>= 28), dhcp-client-udeb | dhcp3-client-udeb |
pump-udeb, ethernet-card-detection
Description: Configure the network
Installer-Menu-Item: 18
Package: zlib1g-udeb
Status: install ok unpacked
Version: 1:1.2.3-13
Provides: zlib1g
Description: compression library - runtime for Debian installer
Package: dhcp-client-udeb
Status: install ok installed
Version: 2.0pl5-19.4
Depends: libc6 (>= 2.3.5-1)
Description: DHCP Client for debian-installer
Package: libdebconfclient0-udeb
Status: install ok installed
Version: 0.109
Depends: libc6 (>= 2.3.5-1), cdebconf-udeb
Description: Debian Configuration Management System (C-implementation)
Package: bogl-bterm-udeb
Status: install ok unpacked
Version: 0.1.18-1.5
Provides: editor
Depends: libc-udeb
Description: Ben's Own Graphics Library - graphical terminal
Package: debian-installer
Status: install ok installed
Version: sparc64-netboot-2.6-20061127-12:05
Description: debian installation image
Package: apt-mirror-setup
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 152
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.16
Depends: choose-mirror-bin, cdebconf-udeb
Description: set up a mirror in sources.list
Package: apt-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 100
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.16
Depends: apt-mirror-setup, base-installer (>= 1.49), cdebconf-udeb
Description: Configure apt
Installer-Menu-Item: 70
Package: base-installer
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 612
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.69
Depends: libc6 (>= 2.3.5-1), libdebconfclient0-udeb, libdebian-installer4-udeb
(>= 0.45), mounted-partitions, debootstrap-udeb (>= 0.3.1), created-fstab,
archdetect, di-utils-mapdevfs, di-utils (>= 1.16), rootskel (>= 1.19)
Provides: kernel-installer
Description: Install the base system
Installer-Menu-Item: 65
Package: cdrom-core-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 216
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di,
scsi-core-modules-2.6.17-2-sparc64-di, ide-modules-2.6.17-2-sparc64-di
Provides: cdrom-core-modules
Description: CDROM support
This package contains core CDROM support for the Linux kernel.
Package: clock-setup
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 72
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.12
Depends: cdebconf-udeb, os-prober, tzsetup-udeb
Description: set up clock
Installer-Menu-Item: 62
Package: debootstrap-udeb
Status: install ok installed
Priority: required
Section: debian-installer
Installed-Size: 160
Maintainer: Anthony Towns <[EMAIL PROTECTED]>
Version: 0.3.3.1
Depends: libc6 (>= 2.3.5-1), mounted-partitions
Description: Bootstrap the Debian system
debootstrap is used to create a Debian base system from scratch,
without requiring the availability of dpkg or apt. It does this by
downloading .deb files from a mirror site, and carefully unpacking them
into a directory which can eventually be chrooted into.
.
debootstrap-udeb is a minimal package used by debian-installer.
Package: dhcp3-client-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 608
Maintainer: Eloy A. Paris <[EMAIL PROTECTED]>
Version: 3.0.4-10
Depends: libc6 (>= 2.3.5-1)
Description: DHCP Client for debian-installer
dhcp-client-udeb is a minimal dhcp package used by the debian-installer.
Package: di-utils-mapdevfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 16
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.41
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.47)
Description: mapdevfs utility for the debian installer
Package: disk-detect
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 60
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.43
Depends: cdebconf-udeb (>= 0.38), hw-detect, di-utils (>= 1.13)
Provides: harddrive-detection
Description: Detect disk drives
Installer-Menu-Item: 35
Package: e2fsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 400
Maintainer: Theodore Y. Ts'o <[EMAIL PROTECTED]>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-1
Depends: libblkid1-udeb, libc6 (>= 2.3.5-1)
Description: stripped-down versions of e2fsprogs, for debian-installer
This package is an e2fsprogs package built for a reduced size, so that
it can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway it should refuse to install.
Package: ext3-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 380
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: ext3-modules
Description: EXT3 filesystem support
This package contains the EXT3 filesystem module for the Linux kernel.
Package: fat-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 168
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: fat-modules
Description: FAT filesystem support
This package contains the FAT and VFAT filesystem modules for the Linux kernel.
Package: finish-install
Status: install ok unpacked
Priority: required
Section: debian-installer
Installed-Size: 108
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2.5
Depends: cdebconf-udeb, archdetect, base-installer, created-fstab,
bootable-system
Provides: prebaseconfig
Description: Finish the installation and reboot
Installer-Menu-Item: 78
Package: ide-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 344
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: ide-modules
Description: IDE drivers
This package contains IDE drivers for the Linux kernel.
Package: jfs-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 312
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: jfs-modules
Description: JFS filesystem support
This package contains the JFS filesystem module for the Linux kernel.
Package: jfsutils-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 1100
Maintainer: Stefan Hornburg (Racke) <[EMAIL PROTECTED]>
Version: 1.1.11-1
Depends: libc6 (>= 2.3.5-1), libuuid1-udeb
Description: A stripped-down version of jfsutils, for debian-installer
This package is a jfsutils package built for reduced size, so that it
can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway, it should fail to install.
Package: libblkid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 44
Maintainer: Theodore Y. Ts'o <[EMAIL PROTECTED]>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-1
Depends: libc6 (>= 2.3.5-1)
Provides: libblkid1
Description: block device id library
The blkid library which allows system programs like fsck and
mount to quickly and easily find block devices by filesystem UUID and
LABEL. This allows system administrators to avoid specifiying
filesystems by hard-coded device names, but via a logical naming
system instead.
.
This is a minimal package for debian-installer.
Package: libc6-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 2028
Maintainer: GNU Libc Maintainers <debian-glibc@lists.debian.org>
Version: 2.3.6.ds1-8
Provides: libc6, libc-udeb, glibc-2.3.6.ds1-1, glibc-2.3.6-2
Description: GNU C Library: Shared libraries - udeb
Contains the standard libraries that are used by nearly all programs on
the system. This package includes shared versions of the standard C library
and the standard math library, as well as many others.
.
This package contains a minimal set of libraries needed for the Debian
installer. Do not install it on a normal system.
Package: libdevmapper1.02-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 84
Maintainer: Debian LVM Team <[EMAIL PROTECTED]>
Version: 2:1.02.08-1
Depends: libc6 (>= 2.3.5-1)
Provides: libdevmapper1.02
Description: The Linux Kernel Device Mapper userspace library
This is a udeb, or a microdeb, for the debian-installer.
.
The Linux Kernel Device Mapper is the LVM (Linux Logical Volume Management)
Team's implementation of a minimalistic kernel-space driver that handles
volume management, while keeping knowledge of the underlying device layout
in user-space. This makes it useful for not only LVM, but EVMS, software
raid, and other drivers that create "virtual" block devices.
Package: libparted1.7-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 404
Maintainer: Parted Maintainer Team <[EMAIL PROTECTED]>
Version: 1.7.1-3
Depends: libc6 (>= 2.3.5-1), libuuid1-udeb
Provides: libparted1.7-1
Description: The GNU Parted disk partitioning shared library
GNU Parted is a program that allows you to create, destroy,
resize, move and copy hard disk partitions. This is useful
for creating space for new operating systems, reorganising
disk usage, and copying data to new hard disks. This package
contains the Parted binary and manual page.
.
This package contains libparted, the required shared library
used by Parted. This is a cut-down package with no normal
documentation intended to be used in debian-installer.
.
Parted currently supports DOS, Mac, Sun, BSD, GPT, MIPS and
PC98 disklabels/partition tables, as well as a 'loop' (raw
disk) type which allows use on RAID/LVM. Filesystems which
are currently fully supported are ext2, ext3, fat (FAT16
and FAT32), ReiserFS (with libreiserfs) and linux-swap.
Parted can also detect and remove HFS (Mac OS), JFS, NTFS,
UFS (Sun and HP), XFS and ASFS/AFFS/APFS (Amiga) filesystems,
but cannot create, resize or check these filesystems yet.
.
Note that ReiserFS support is only enabled if you install
the libreiserfs0.3-0 package. Since libreiserfs0.3-0 has been
removed from sarge, ReiserFS support is not compiled in the
default package.
.
The nature of this software means that any bugs could cause
massive data loss. While there are no known bugs at the moment,
they could exist, so please back up all important files before
running it, and do so at your own risk.
Package: libuuid1-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 24
Maintainer: Theodore Y. Ts'o <[EMAIL PROTECTED]>
Version: 1.39+1.40-WIP-2006.11.14+dfsg-1
Depends: libc6 (>= 2.3.5-1)
Provides: libuuid1
Description: universally unique id library
libuuid generates and parses 128-bit universally unique id's (UUID's).
See RFC 4122 for more information.
.
This is a minimal package for debian-installer.
Package: lvm2-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 516
Maintainer: Debian LVM Team <[EMAIL PROTECTED]>
Version: 2.02.06-3
Depends: libc6 (>= 2.3.5-1), libdevmapper1.02-udeb (>= 2:1.02.02-2)
Description: The Linux Logical Volume Manager
This is a udeb, or a microdeb, for the debian-installer.
.
This is LVM2, the rewrite of The Linux Logical Volume Manager. LVM
supports enterprise level volume management of disk and disk subsystems
by grouping arbitrary disks into volume groups. The total capacity of
volume groups can be allocated to logical volumes, which are accessed as
regular block devices.
Package: md-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 504
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: md-modules
Description: RAID and LVM support
This package contains RAID and LVM modules for the Linux kernel.
Package: mdadm-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 208
Maintainer: Debian mdadm maintainers <[EMAIL PROTECTED]>
Version: 2.5.6-6
Depends: libc6 (>= 2.3.5-1)
Description: tool to administer Linux MD arrays (software RAID)
mdadm is a program that can be used to create, manage, and monitor MD
arrays (e.g. software RAID, multipath devices).
.
mdadm-udeb is a minimal package used by the debian-installer.
Package: mdcfg-utils
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 384
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.19
Depends: cdebconf-udeb, di-utils (>= 1.16), md-modules, mdadm-udeb (>= 2.5.2),
partconf-find-partitions
Description: Configure MD devices
Use this module to configure the MD devices.
Package: mkreiserfs-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 192
Maintainer: Ed Boraas <[EMAIL PROTECTED]>
Version: 1:3.6.19-4
Depends: libc6 (>= 2.3.5-1), libuuid1-udeb
Description: User-level tools for ReiserFS filesystems
This installer module contains the utility to create ReiserFS filesystems.
.
Homepage: http://www.namesys.com/
Package: nobootloader
Status: install ok unpacked
Priority: standard
Section: debian-installer
Installed-Size: 156
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.15
Depends: cdebconf-udeb, base-installer (>= 1.23), di-utils-mapdevfs
Provides: bootable-system
Description: Don't install any bootloader.
This package will skip installing a boot-loader
Installer-Menu-Item: 77
Package: os-prober-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 96
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: di-utils-mapdevfs, anna (>= 1.16)
Provides: os-prober
Description: utility to detect other OSes on a set of drives
This package is to be used by boot loader installers to detect other OSes
available on a system, in a generic format, which it can then adapt to its
own configuration format.
Package: partconf-find-partitions
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 32
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.19
Depends: libc6 (>= 2.3.5-1), libdebian-installer4-udeb (>= 0.45),
libparted1.7-udeb (>= 1.7.1-1)
Description: debian-installer utility for finding partitions
Helper program for finding partitions and detecting their size and
existing file system.
Package: parted-udeb
Status: install ok installed
Priority: extra
Section: debian-installer
Installed-Size: 68
Maintainer: Parted Maintainer Team <[EMAIL PROTECTED]>
Version: 1.7.1-3
Depends: libc6 (>= 2.3.5-1), libparted1.7-udeb (>= 1.7.1-1)
Provides: parted
Description: The GNU Parted disk partition resizing program
GNU Parted is a program that allows you to create, destroy,
resize, move and copy hard disk partitions. This is useful
for creating space for new operating systems, reorganising
disk usage, and copying data to new hard disks. This package
contains the Parted binary and manual page.
.
This package is similar to the "big" parted package, but has
less cosmetical features resulting in smaller binary. Intended
to be used in debian-installer.
.
.
The nature of this software means that any bugs could cause
massive data loss. While there are no known bugs at the moment,
they could exist, so please back up all important files before
running it, and do so at your own risk.
Package: partman-auto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 376
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 61
Depends: cdebconf-udeb, di-utils, partman-base, partman-basicfilesystems,
partman-ext3
Description: Automatically partition storage devices (partman)
Package: partman-auto-crypto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 48
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 3
Depends: cdebconf-udeb, partman-auto (>= 55), partman-auto-lvm (>= 14),
partman-crypto (>= 13), partman-base (>= 87)
Description: Automatically partition storage devices using crypto and LVM
Package: partman-auto-lvm
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 148
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 18
Depends: cdebconf-udeb, partman-base (>= 73), partman-auto (>= 59), partman-lvm
(>= 36), di-utils (>= 1.15), lvm2-udeb
Description: Automatically partition storage devices using LVM
Package: partman-auto-raid
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 64
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 2
Depends: cdebconf-udeb, partman-base, partman-basicfilesystems, partman-ext3,
partman-auto (>= 58), partman-md
Description: Allow preseeded RAID installs
Package: partman-base
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 860
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 98
Depends: libc6 (>= 2.3.5-1), libparted1.7-udeb (>= 1.7.1-1), cdebconf-udeb,
partman-partitioning, partman-target, archdetect, harddrive-detection,
di-utils-mapdevfs, di-utils (>= 1.15)
Provides: made-filesystems, mounted-partitions, partitioned-harddrives,
created-fstab
Description: Partition the storage devices (partman)
Installer-Menu-Item: 42
Package: partman-basicfilesystems
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 576
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 49
Depends: cdebconf-udeb, e2fsprogs-udeb, ext2-modules, fat-modules, di-utils (>=
1.14)
Provides: partman-filesystem
Description: Add to partman support for ext2, linux-swap, fat16 and fat32
Package: partman-basicmethods
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 124
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 32
Depends: cdebconf-udeb
Provides: partman-method
Description: Basic partition usage methods for partman
This package provides partman with two methods to use partitions.
The first is to format the partition. The second is to keep and use
the existing data in the partition as it is.
Package: partman-crypto
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 860
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 17
Depends: partman-base (>= 87), libc6 (>= 2.3.5-1), cdebconf-udeb
Description: Add to partman support for block device encryption
Package: partman-ext3
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 220
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 43
Depends: cdebconf-udeb, e2fsprogs-udeb, ext3-modules, partman-basicfilesystems,
di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for ext3
Package: partman-jfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 260
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 18
Depends: cdebconf-udeb, jfsutils-udeb, jfs-modules, partman-basicfilesystems,
di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add support for jfs to partman
Package: partman-lvm
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 680
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 47
Depends: cdebconf-udeb, partman-base (>= 87), di-utils (>= 1.14), md-modules,
lvm2-udeb, parted-udeb
Description: Adds support for LVM to partman
Package: partman-md
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 156
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 30
Depends: cdebconf-udeb, mdadm-udeb, mdcfg-utils, partman-base (>= 87)
Description: Add to partman support for MD
Package: partman-partitioning
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 364
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 44
Depends: cdebconf-udeb
Description: Partitioning operations for partman
This udeb provides partman with editing operations for creation
of new partitions, deletion of partitions and initialisation of the
partition table.
Package: partman-reiserfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 228
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 32
Depends: cdebconf-udeb, mkreiserfs-udeb, reiserfs-modules,
partman-basicfilesystems, di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for reiserfs
Package: partman-target
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 304
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 46
Depends: cdebconf-udeb, partman-basicfilesystems, partman-basicmethods,
di-utils-mapdevfs
Description: Provides partman with ability to prepare /target
This udeb allows the user to choose how partitions should be used.
Package: partman-xfs
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 216
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 30
Depends: cdebconf-udeb, xfsprogs-udeb, xfs-modules, partman-basicfilesystems,
di-utils (>= 1.14)
Provides: partman-filesystem
Description: Add to partman support for xfs
Package: pkgsel
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 28
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 0.10
Depends: cdebconf-udeb, apt-setup-udeb, di-utils (>= 1.20)
Description: Select and install packages
Installer-Menu-Item: 70
Package: reiserfs-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 452
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: reiserfs-modules
Description: Reiser filesystem support
This package contains the Reiser filesystem module for the Linux kernel.
Package: sata-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 496
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di, scsi-core-modules-2.6.17-2-sparc64-di
Provides: sata-modules
Description: SATA drivers
This package contains SATA drivers for the Linux kernel.
Package: scsi-common-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 1416
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di,
scsi-core-modules-2.6.17-2-sparc64-di, cdrom-core-modules-2.6.17-2-sparc64-di
Provides: scsi-common-modules
Description: Very common SCSI drivers
This package contains very common SCSI drivers for the Linux kernel.
Package: scsi-core-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 364
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: scsi-core-modules
Description: Core SCSI subsystem
This package contains the core SCSI subsystem for the Linux kernel.
Package: scsi-extra-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 1416
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: scsi-core-modules-2.6.17-2-sparc64-di
Provides: scsi-extra-modules
Description: Uncommon SCSI drivers
This package contains uncommon SCSI drivers for the Linux kernel.
This includes SCSI RAID drivers, and some of the less common SCSI
controllers.
Package: silo-installer
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 196
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.07
Depends: cdebconf-udeb, base-installer, di-utils-mapdevfs, archdetect
Provides: bootable-system
Description: install silo on a hard disk
This udeb will install silo on the hard disk.
Installer-Menu-Item: 73
Package: tzsetup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 300
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1:0.13
Depends: cdebconf-udeb, localechooser
Description: choose timezone
Installer-Menu-Item: 62
Package: user-setup-udeb
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 336
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.7
Depends: cdebconf-udeb
Description: Set up users and passwords
Installer-Menu-Item: 63
Package: xfs-modules-2.6.17-2-sparc64-di
Status: install ok installed
Priority: standard
Section: debian-installer
Installed-Size: 728
Maintainer: Debian Install System Team <debian-boot@lists.debian.org>
Version: 1.14
Depends: kernel-image-2.6.17-2-sparc64-di
Provides: xfs-modules
Description: XFS filesystem support
This package contains the XFS filesystem module for the Linux kernel.
Package: xfsprogs-udeb
Status: install ok installed
Priority: optional
Section: debian-installer
Installed-Size: 256
Maintainer: Nathan Scott <[EMAIL PROTECTED]>
Version: 2.8.11-1
Depends: libc6 (>= 2.3.5-1), libuuid1-udeb
Description: A stripped-down version of xfsprogs, for debian-installer
This package is an xfsprogs package built for reduced size, so that it
can help to save space in debian-installer.
.
Don't attempt to install this package, it has no support for a couple of
features you surely want. Anyway, it should fail to install.
-- System Information:
Debian Release: 4.0
APT prefers testing
APT policy: (500, 'testing')
Architecture: sparc (sparc64)
Shell: /bin/sh linked to /bin/bash
Kernel: Linux 2.6.17-2-sparc64
Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8)
installation-report depends on no packages.
Versions of packages installation-report recommends:
pn pciutils <none> (no description available)
ii reportbug 3.31 reports bugs in the Debian distrib
-- no debconf information
--- End Message ---