Your message dated Sat, 22 Aug 2009 00:47:40 +0200 with message-id <[email protected]> and subject line Re: Bug#504016: Lenny Beta II + daily build, kernel dies after initrd.gz....ready. has caused the Debian Bug report #504016, regarding Lenny Beta II + daily build, kernel dies after initrd.gz....ready. to be marked as done.
This means that you claim that the problem has been dealt with. If this is not the case it is now your responsibility to reopen the Bug report if necessary, and/or fix the problem forthwith. (NB: If you are a system administrator and have no idea what this message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact [email protected] immediately.) -- 504016: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=504016 Debian Bug Tracking System Contact [email protected] with problems
--- Begin Message ---Package: Installation-reports Boot method: Booted from CD The following is copied from Etch dmesg sym0: <810a> rev 0x12 at pci 0000:00:0c.0 irq 11 sym0: No NVRAM, ID 7, Fast-10, SE, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.2.3 Vendor: PLEXTOR Model: CD-ROM PX-40TS Rev: 1.01 Type: CD-ROM ANSI SCSI revision: 02 target0:0:1: Beginning Domain Validation target0:0:1: asynchronous target0:0:1: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 8) BIOS is SDMS 4.12.0.0, and reports "No Emulation" mode on BIOS screen while booting. Image version: 157034496 2008-10-28 22:11 debian-LennyBeta2-i386-netinst.iso Second try with daily build debian-testing-i386-netinst.iso from http://cdimage.debian.org/cdimage/daily-builds/daily/arch-latest/i386/iso-cd/ But it is also reproducible with a Knoppix CD, and therefore probably a general Isolinux problem not limited to the Debian Installer. Date: Oct 29 Machine: Homebuilt 24/7 machine, motherboard ASUS A7V 1.04 with latest BIOS 1011 from 2002, running under Debian Etch normally. SCSI controller is an ASUS SC-200, SDMS BIOS 4.12.0.0 is delivered by the motherboard, as usual for these controllers. Processor: Duron 600 CPU: After generic identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000 CPU: After vendor identify, caps: 0183f9ff c1c7f9ff 00000000 00000000 00000000 00000000 00000000 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 64K (64 bytes/line) CPU: After all inits, caps: 0183f9ff c1c7f9ff 00000000 00000420 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: AMD Duron(tm) Processor stepping 00 Checking 'hlt' instruction... OK. Memory: SDRAM 100 383MB LOWMEM available. Partitions: Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/hda1 ext3 21342047 4444456 15813206 22% / tmpfs tmpfs 193452 0 193452 0% /lib/init/rw udev tmpfs 10240 84 10156 1% /dev tmpfs tmpfs 193452 8 193444 1% /dev/shm /dev/hdc2 ext3 91658564 44736272 42266256 52% /home /dev/hde1 ext3 476750548 341159516 111373448 76% /home/hajo/Archiv /dev/hdf1 ext3 240362656 143533616 84619240 63% /home/hajo/Archiv/Bahn Output of lspci -knn (or lspci -nn): 00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] [1106:0305] (rev 02) 00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] [1106:8305] 00:04.0 ISA bridge [0601]: VIA Technologies, Inc. VT82C686 [Apollo Super South] [1106:0686] (rev 22) 00:04.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 10) 00:04.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 10) 00:04.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 10) 00:04.4 Bridge [0680]: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] [1106:3057] (rev 30) 00:09.0 Multimedia video controller [0400]: Brooktree Corporation Bt878 Video Capture [109e:036e] (rev 02) 00:09.1 Multimedia controller [0480]: Brooktree Corporation Bt878 Audio Capture [109e:0878] (rev 02) 00:0a.0 Multimedia controller [0480]: Philips Semiconductors TriMedia TM-1300 [1131:5402] (rev 83) 00:0b.0 PCI bridge [0604]: IBM IBM27-82351 [1014:0022] (rev 01) 00:0c.0 SCSI storage controller [0100]: LSI Logic / Symbios Logic 53c810 [1000:0001] (rev 12) 00:0d.0 Multimedia audio controller [0401]: C-Media Electronics Inc CM8738 [13f6:0111] (rev 10) 00:11.0 Mass storage controller [0180]: Promise Technology, Inc. PDC20265 (FastTrak100 Lite/Ultra100) [105a:0d30] (rev 02) 01:00.0 VGA compatible controller [0300]: Matrox Graphics, Inc. MGA G400/G450 [102b:0525] (rev 04) 02:00.0 Network controller [0280]: Compaq Computer Corporation Netelligent Dual 10/100 TX PCI UTP [0e11:ae40] (rev 10) 02:01.0 Network controller [0280]: Compaq Computer Corporation Netelligent Dual 10/100 TX PCI UTP [0e11:ae40] (rev 10) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot: [E] Detect network card: [ ] Configure network: [ ] Detect CD: [ ] Load installer modules: [ ] Detect hard drives: [ ] Partition hard drives: [ ] Install base system: [ ] Clock/timezone setup: [ ] User/password setup: [ ] Install tasks: [ ] Install boot loader: [ ] Overall install: [ ] Comments/Problems: BIOS boot uneventful, Hostadapter BIOS reports "No Emulation" mode, Installation CD screen comes up fine with all the help options. After <Enter>, I get Loading /something-386/vmlinuz ..................... Loading /something-386/initrd.gz ....................................... .........................ready. After that, the machine stops activity, nothing even after 10 minutes, and does not react to Ctrl-Alt-Del. Hardware reset necessary. I also tried with Kernel boot parameters "noapic nolapic acpi=off" with the same results. After the Lenny II Beta, I tried with another CD from daily build, and I also tried with Knoppix. Knoppix gives the same result to ...........ready, just with different naming for kernel and initrd.
--- End Message ---
--- Begin Message ---On Sat, Aug 22, 2009 at 12:36:01AM +0200, Moritz Muehlenhoff wrote: > On Wed, Nov 05, 2008 at 10:10:54PM +0100, Frans Pop wrote: > > reassign 504016 linux-2.6 > > thanks > > > > Hans-Joachim, did you try later versions of the installer on this > system? Did any of them succeed? Submitter's address bounces, closing. Cheers, Moritz
--- End Message ---
