Your message dated Fri, 10 May 2019 22:46:18 +0200
with message-id <[email protected]>
and subject line arch:sparc has been removed from Debian
has caused the Debian Bug report #266727,
regarding Comments on netboot instructions (sparc64)
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact [email protected]
immediately.)
--
266727: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=266727
Debian Bug Tracking System
Contact [email protected] with problems
--- Begin Message ---
Package: installation-reports
INSTALL REPORT
Debian-installer-version: d-i rc1
(http://http.us.debian.org/debian/dists/testing/main/installer-sparc/rc1/images/sparc64/netboot/boot.img,
02-Aug-2004)
uname -a: Linux ultra 2.4.26-sparc64 #1 Sun Jun 20 02:39:17 PDT 2004 sparc64
GNU/Linux
Date: 17-Aug-2004
Method: Netboot, using rarpd to serve IP, atftpd to serve image, dhcp for
network configuration, package install via net/apt-proxy
Machine: SUN Ultra1/Creator
Processor: TI UltraSparc I (SpitFire) sun4u
Memory: 382136 kB
Root Device: SCSI, /dev/sda1
Root Size/partition table:
Disk /dev/sda (Sun disk label): 14 heads, 72 sectors, 2036 cylinders
Units = cylinders of 1008 * 512 bytes
Device Flag Start End Blocks Id System
/dev/sda1 0 1872 943488 1 Boot
/dev/sda2 1872 2036 82656 82 Linux swap
/dev/sda3 0 2036 1026144 5 Whole disk
Output of lspci and lspci -n: no PCI, only SBus
Base System Installation Checklist:
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [ ]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [O]
Install boot loader: [O]
Reboot: [O]
Comments/Problems:
Using the simple (non-expert modus) install, this works like a breeze, no
problems.
Some comments on the installation manual for sparc:
In "4.4. Preparing Files for TFTP Net Booting" it says that you can use either
of RARP, BOOTP or DHCP for net booting. On this machine, I had to setup rarpd
_and_ dhcpd, rarpd for giving the machine an IP, which is then used to retrieve
the netboot image via tftp. It uses the IP in hex format as the image name, not
IP_in_hex.SUN4M as the text suggests. d-i then uses dhcp to retrieve the
network information.
And in the dhcp setup example, there is the line
filename "/tftpboot/tftpboot.img";
This should read
filename "/tftpboot.img";
since tftpd serves only from the tftboot directory anyway (whatever it is
named).
--- End Message ---
--- Begin Message ---
Version: 20140916
The (32-bit) sparc architecture was last released with Debian 7.0
(wheezy) in May 2013 and was removed from the Debian archive afterwards.
Since support for wheezy has now ended and the suites have been
archived, I'm closing all the remaining bugs reported against
sparc specific packages.
Andreas
--- End Message ---
