Package: installation-reports INSTALL REPORT
Debian-installer-version: rc2 uname -a: Linux trysia 2.4.27-2-586tsc #1 Thu Dec 30 18:06:49 JST 2004 i586 GNU/Linux Date: 1/28/2005 Method: Network install from HTTP mirror, direct connection, PCMCIA network card. Used rc2 floppy images. Machine: Toshiba Tecra 500CDT Processor: 120MHz Pentium Memory: 144MB Root Device: 4GB IDE Root Size/partition table: (parted) p Disk geometry for /dev/hda: 0.000-4645.634 megabytes Disk label type: msdos Minor Start End Type Filesystem Flags 1 0.031 4196.206 primary ext3 boot 2 4196.206 4496.132 primary 3 4496.133 4645.634 extended lba 5 4496.164 4645.634 logical linux-swap Output of lspci and lspci -n: 0000:00:00.0 Host bridge: Toshiba America Info Systems 601 (rev 11) 0000:00:04.0 VGA compatible controller: Chips and Technologies F65550 (rev 04) 0000:00:00.0 0600: 1179:0601 (rev 11) 0000:00:04.0 0300: 102c:00e0 (rev 04) Base System Installation Checklist: [O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it Initial boot worked: [O] Configure network HW: [E] Config network: [O] Detect CD: [O] Load installer modules: [O] Detect hard drives: [O] Partition hard drives: [O] Create file systems: [O] Mount partitions: [O] Install base system: [O] Install boot loader: [O] Reboot: [O] Comments/Problems: The installation went very well. Few notes for this machine. The kernel pcmcia drivers for 2.4 and 2.6 do not work with a 16-bit card when the slot is set to Cardbus/16-bit mode in the BIOS. It must be reset to PCIC Compatible for this to work, or else the pcmcia-cs drivers can be used instead, since they work fine. (For some reason the 2.6 Toshiba support is _worse_ than pcmcia-cs.) This is why I report an error in configure network HW above, since it was impossible to get the 16-bit network card to work without changing the BIOS setting (which the user may have no idea is the problem why his network card doesn't work). Also, I had to install ifplugd and waproamd/wireless-tools myself. It seems that these should automatically be installed if a hotplug network card (and/or a wireless card) exists. Crystal sound chip has fixed resources set in the BIOS (some port ranges, irq=5 and irq=9). Unfortunately, /etc/pcmcia/config.opts must be manually edited to reflect this exclusions, otherwise the PCMCIA card takes over that IRQ. Perhaps this chip should be added to discover's hardware detection - its resources can be read from its configuration port and appropriate action automatically taken. The rest is nitpicks: Only 64MB of RAM is cacheable. The optimal setup for performance is to limit mem=63M and then mount a slram mtd device over the rest for swap (highest swap priority). I don't think this can be detected though. The machine needs a APM hibernate partition (type=0xa0) for APM suspend to work. It would be nice if this were able to be automatically setup on machines which report APM capability. It would seem that installing smartmontools by default would be reasonable. You can use smartctl to determine whether the machine supports SMART, and if so, change /etc/default/smartmontools to Yes so that smartd is run. Bonus points to automatically mail root when a disk error occurs (-m option to smartd). It is too bad that we can't use DMI for these older special-case machines, since they have not DMI pool. Install logs and other status info is available in /var/log/debian-installer/. Once you have filled out this report, mail it to [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
