Here is some more information of our machine FYI. Attached dmesg_20120322T184612.txt is the dmesg generated during boot of the machine on Mar 22, 2012, which is the date we did our last reboot and put it into production.
The machine has 14GB RAM, that is 512MB*(16+12). Because there is one broken RAM, we have to remove all the group of four to make the machine boot, so there is 2GB's loss. The network is dual-stacked IPv4 and IPv6. Both of the NICs have configured multiple IPv6 addresses, only one of them have one IPv4 address. But I confirm it does not have any problem with no connection or have only one NIC configured. The operating system when installed is 6.0.4, user space programs are updated to 6.0.5 later, but the kernel isn't updated. The kernel is linux-image-2.6.32-5-sparc64-smp, version 2.6.32-41squeeze2. I can confirm that 2.6.32-41 worked because its the default of 6.0.4 CD1. d-i prompted for firmware during installation, and I supplied all the firmware.tar.gz as well as an unpacked directory by a USB flash disk. Then the installation continued. The disk is configured as software RAID1 (hardware RAID card seems not being recognized), though /boot as a separated partition isn't configured in the RAID due to a glitch in d-i. /boot is ext3, and / is ext4. The Sun remote control card is installed but not configured. The server's load is normally not very high, but it's usually to have a load average of 2 ~ 3. Most of the loads are processing network requests with very few disk I/O. $ cat /proc/cpuinfo cpu : TI UltraSparc III+ (Cheetah+) fpu : UltraSparc III+ integrated FPU pmu : ultra3+ prom : OBP 4.13.0 2004/01/19 18:26 type : sun4u ncpus probed : 4 ncpus active : 4 D$ parity tl1 : 0 I$ parity tl1 : 0 Cpu0ClkTck : 0000000047868c00 Cpu1ClkTck : 0000000047868c00 Cpu2ClkTck : 0000000047868c00 Cpu3ClkTck : 0000000047868c00 MMU Type : Cheetah+ State: CPU0: online CPU1: online CPU2: online CPU3: online $ lspci 0000:00:03.0 VGA compatible controller: ATI Technologies Inc Radeon RV100 QY [Radeon 7000/VE] 0000:00:06.0 IDE interface: Silicon Image, Inc. PCI0646 (rev 07) 0001:00:01.0 Fibre Channel: QLogic Corp. ISP2422-based 4Gb Fibre Channel to PCI-X HBA (rev 02) 0002:00:01.0 Bridge: Oracle Corporation RIO EBUS (rev 01) 0002:00:01.3 USB Controller: Oracle Corporation RIO USB (rev 01) 0002:00:02.0 Ethernet controller: Oracle Corporation Cassini 10/100/1000 (rev 20) 0003:00:01.0 Ethernet controller: Oracle Corporation Cassini 10/100/1000 (rev 20) 0003:00:02.0 SCSI storage controller: QLogic Corp. QLA2200 64-bit Fibre Channel Adapter (rev 05) -- Regards, Aron Xu
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.13.0 2004/01/19 18:26' [ 0.000000] PROMLIB: Root node compatible: [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.32-5-sparc64-smp (Debian 2.6.32-41squeeze2) (da...@debian.org) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Thu Mar 22 18:46:12 UTC 2012 [ 0.000000] bootconsole [earlyprom0] enabled [ 0.000000] ARCH: SUN4U [ 0.000000] Ethernet address: 00:03:ba:8c:1f:11 [ 0.000000] Kernel: Using 2 locked TLB entries for main kernel image. [ 0.000000] Remapping the kernel... done. [ 0.000000] OF stdout device is: /pci@8,700000/SUNW,XVR-100@3 [ 0.000000] PROM: Built device tree with 119498 bytes of memory. [ 0.000000] Top of RAM: 0xb17fa6e000, Total RAM: 0x37fa5c000 [ 0.000000] Memory hole size: 712704MB [ 0.000000] [0000010140000000-fffff8a000400000] page_structs=131072 node=0 entry=1280/0 [ 0.000000] [0000010140000000-fffff8a000800000] page_structs=131072 node=0 entry=1281/0 [ 0.000000] [0000010140800000-fffff8a000c00000] page_structs=131072 node=0 entry=1282/0 [ 0.000000] [0000010140800000-fffff8a001000000] page_structs=131072 node=0 entry=1283/0 [ 0.000000] [0000010141000000-fffff8a001400000] page_structs=131072 node=0 entry=1284/0 [ 0.000000] [0000010141000000-fffff8a001800000] page_structs=131072 node=0 entry=1285/0 [ 0.000000] [0000010141800000-fffff8a001c00000] page_structs=131072 node=0 entry=1286/0 [ 0.000000] [0000010141800000-fffff8a002000000] page_structs=131072 node=0 entry=1287/0 [ 0.000000] [0000010142000000-fffff8a002400000] page_structs=131072 node=0 entry=1288/0 [ 0.000000] [0000010142000000-fffff8a002800000] page_structs=131072 node=0 entry=1289/0 [ 0.000000] [0000010142800000-fffff8a002c00000] page_structs=131072 node=0 entry=1290/0 [ 0.000000] [0000010142800000-fffff8a003000000] page_structs=131072 node=0 entry=1291/0 [ 0.000000] [0000010143000000-fffff8a003400000] page_structs=131072 node=0 entry=1292/0 [ 0.000000] [0000010143000000-fffff8a003800000] page_structs=131072 node=0 entry=1293/0 [ 0.000000] [0000010143800000-fffff8a003c00000] page_structs=131072 node=0 entry=1294/0 [ 0.000000] [0000010143800000-fffff8a004000000] page_structs=131072 node=0 entry=1295/0 [ 0.000000] [0000010160000000-fffff8a004400000] page_structs=131072 node=0 entry=1408/0 [ 0.000000] [0000010160000000-fffff8a004800000] page_structs=131072 node=0 entry=1409/0 [ 0.000000] [0000010160800000-fffff8a004c00000] page_structs=131072 node=0 entry=1410/0 [ 0.000000] [0000010160800000-fffff8a005000000] page_structs=131072 node=0 entry=1411/0 [ 0.000000] [0000010161000000-fffff8a005400000] page_structs=131072 node=0 entry=1412/0 [ 0.000000] [0000010161000000-fffff8a005800000] page_structs=131072 node=0 entry=1413/0 [ 0.000000] [0000010161800000-fffff8a005c00000] page_structs=131072 node=0 entry=1414/0 [ 0.000000] [0000010161800000-fffff8a006000000] page_structs=131072 node=0 entry=1415/0 [ 0.000000] [0000010162000000-fffff8a006400000] page_structs=131072 node=0 entry=1416/0 [ 0.000000] [0000010162000000-fffff8a006800000] page_structs=131072 node=0 entry=1417/0 [ 0.000000] [0000010162800000-fffff8a006c00000] page_structs=131072 node=0 entry=1418/0 [ 0.000000] [0000010162800000-fffff8a007000000] page_structs=131072 node=0 entry=1419/0 [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x05000000 -> 0x058bfd37 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[4] active PFN ranges [ 0.000000] 0: 0x05000000 -> 0x05100000 [ 0.000000] 0: 0x05800000 -> 0x058bf7ff [ 0.000000] 0: 0x058bf800 -> 0x058bfd20 [ 0.000000] 0: 0x058bfd28 -> 0x058bfd37 [ 0.000000] On node 0 totalpages: 1834286 [ 0.000000] Normal zone: 71675 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 1762611 pages, LIFO batch:15 [ 0.000000] Booting Linux... [ 0.000000] PERCPU: Embedded 7 pages/cpu @fffff8a007400000 s25984 r8192 d23168 u1048576 [ 0.000000] pcpu-alloc: s25984 r8192 d23168 u1048576 alloc=1*4194304 [ 0.000000] pcpu-alloc: [0] 0 1 2 3 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 1762611 [ 0.000000] Kernel command line: root=/dev/md0 ro [ 0.000000] PID hash table entries: 4096 (order: 2, 32768 bytes) [ 0.000000] Dentry cache hash table entries: 2097152 (order: 11, 16777216 bytes) [ 0.000000] Inode-cache hash table entries: 1048576 (order: 10, 8388608 bytes) [ 0.000000] Memory: 14517504k available (3448k kernel code, 1432k data, 240k init) [fffff80000000000,000000b17fa6e000] [ 0.000000] SLUB: Genslabs=14, HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:255 [ 0.000000] clocksource: mult[640000] shift[16] [ 0.000000] clockevent: mult[28f5c28] shift[32] [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [tty0] enabled, bootconsole disabled [ 69.600913] Calibrating delay using timer specific routine.. 20.00 BogoMIPS (lpj=40019) [ 69.600987] Security Framework initialized [ 69.601015] SELinux: Disabled at boot. [ 69.601042] Mount-cache hash table entries: 512 [ 69.601541] Initializing cgroup subsys ns [ 69.601557] Initializing cgroup subsys cpuacct [ 69.601593] Initializing cgroup subsys devices [ 69.601604] Initializing cgroup subsys freezer [ 69.601614] Initializing cgroup subsys net_cls [ 69.603349] CPU 0: synchronized TICK with master CPU (last diff 0 cycles, maxerr 10 cycles) [ 69.604430] CPU 1: synchronized TICK with master CPU (last diff 0 cycles, maxerr 10 cycles) [ 69.605530] CPU 2: synchronized TICK with master CPU (last diff 0 cycles, maxerr 10 cycles) [ 69.605543] Brought up 4 CPUs [ 69.605583] CPU0 attaching sched-domain: [ 69.605592] domain 0: span 0-3 level CPU [ 69.605600] groups: group fffff8a007401c80 cpus 0 group fffff8a007501c80 cpus 1 group fffff8a007601c80 cpus 2 group fffff8a007701c80 cpus 3 [ 69.605627] CPU1 attaching sched-domain: [ 69.605633] domain 0: span 0-3 level CPU [ 69.605639] groups: group fffff8a007501c80 cpus 1 group fffff8a007601c80 cpus 2 group fffff8a007701c80 cpus 3 group fffff8a007401c80 cpus 0 [ 69.605661] CPU2 attaching sched-domain: [ 69.605667] domain 0: span 0-3 level CPU [ 69.605673] groups: group fffff8a007601c80 cpus 2 group fffff8a007701c80 cpus 3 group fffff8a007401c80 cpus 0 group fffff8a007501c80 cpus 1 [ 69.605693] CPU3 attaching sched-domain: [ 69.605699] domain 0: span 0-3 level CPU [ 69.605705] groups: group fffff8a007701c80 cpus 3 group fffff8a007401c80 cpus 0 group fffff8a007501c80 cpus 1 group fffff8a007601c80 cpus 2 [ 69.606507] devtmpfs: initialized [ 69.607269] regulator: core version 0.5 [ 69.607442] NET: Registered protocol family 16 [ 69.611758] Testing NMI watchdog ... OK. [ 69.691781] Performance events: Supported PMU type is 'ultra3+' [ 69.692534] /pci@8,700000: SCHIZO PCI Bus Module ver[7:0] [ 69.692551] /pci@8,700000: PCI IO[7ffef000000] MEM[7fe00000000] [ 69.696789] PCI: Scanning PBM /pci@8,700000 [ 69.696934] pci 0000:00:03.0: supports D1 D2 [ 69.697006] pci 0000:00:06.0: supports D1 D2 [ 69.697224] /pci@8,600000: SCHIZO PCI Bus Module ver[7:0] [ 69.697246] /pci@8,600000: PCI IO[7ffed000000] MEM[7fd00000000] [ 69.701480] PCI: Scanning PBM /pci@8,600000 [ 69.701780] /pci@9,700000: SCHIZO PCI Bus Module ver[7:0] [ 69.701800] /pci@9,700000: PCI IO[7ffeb000000] MEM[7fc00000000] [ 69.706139] PCI: Scanning PBM /pci@9,700000 [ 69.707807] /pci@9,600000: SCHIZO PCI Bus Module ver[7:0] [ 69.707828] /pci@9,600000: PCI IO[7ffe9000000] MEM[7fb00000000] [ 69.712191] PCI: Scanning PBM /pci@9,600000 [ 69.714548] bio: create slab <bio-0> at 0 [ 69.715156] vgaarb: device added: PCI:0000:00:03.0,decodes=io+mem,owns=mem,locks=none [ 69.715193] vgaarb: loaded [ 69.715924] /pci@9,700000/ebus@1/rtc@1,300070: RTC regs at 0x7fc7e300070 [ 69.716324] Switching to clocksource stick [ 69.720966] NET: Registered protocol family 2 [ 69.721310] IP route cache hash table entries: 524288 (order: 9, 4194304 bytes) [ 69.726778] TCP established hash table entries: 524288 (order: 10, 8388608 bytes) [ 69.757703] TCP bind hash table entries: 65536 (order: 7, 1048576 bytes) [ 69.761666] TCP: Hash tables configured (established 524288 bind 65536) [ 69.761687] TCP reno registered [ 69.762049] NET: Registered protocol family 1 [ 69.762360] Unpacking initramfs... [ 70.224107] Freeing initrd memory: 10028k freed [ 70.225084] power: Control reg at 7fc7e30002e [ 70.225368] chmc: UltraSPARC-III memory controller at /memory-controller@0,400000 [ACTIVE] [ 70.225414] chmc: UltraSPARC-III memory controller at /memory-controller@1,400000 [ACTIVE] [ 70.225459] chmc: UltraSPARC-III memory controller at /memory-controller@2,400000 [ACTIVE] [ 70.225500] chmc: UltraSPARC-III memory controller at /memory-controller@3,400000 [ACTIVE] [ 70.225783] audit: initializing netlink socket (disabled) [ 70.225832] type=2000 audit(0.705:1): initialized [ 70.232781] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 70.237473] VFS: Disk quotas dquot_6.5.2 [ 70.237670] Dquot-cache hash table entries: 1024 (order 0, 8192 bytes) [ 70.237909] msgmni has been set to 28375 [ 70.238878] alg: No test for stdrng (krng) [ 70.239073] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 70.239105] io scheduler noop registered [ 70.239120] io scheduler anticipatory registered [ 70.239135] io scheduler deadline registered [ 70.239298] io scheduler cfq registered (default) [ 70.239574] PCI: Enabling device: (0000:00:03.0), cmd 83 [ 70.239608] radeonfb 0000:00:03.0: BAR 6: can't allocate resource (bogus alignment) [0x7fe00120000-0x7fe0013ffff] flags 0x6200 [ 70.239636] radeonfb (0000:00:03.0): ROM failed to map [ 70.250235] radeonfb: Retrieved PLL infos from Open Firmware [ 70.250256] radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=150.00 Mhz, System=150.00 MHz [ 70.250280] radeonfb: PLL min 12000 max 35000 [ 70.308726] radeonfb: Monitor 1 type CRT found [ 70.308743] radeonfb: Monitor 2 type no found [ 70.659161] Console: switching to colour frame buffer device 80x30 [ 70.673683] radeonfb (0000:00:03.0): ATI Radeon 5159 "QY" [ 70.678256] [drm] Initialized drm 1.1.0 20060810 [ 70.680421] f00a6cc8: ttyS0 at MMIO 0x7fc7e3062f8 (irq = 15) is a 16550A [ 70.682673] f00a84d8: ttyS1 at MMIO 0x7fc7e3083f8 (irq = 16) is a 16550A [ 70.685219] f00a9ce8: ttyS2 at MMIO 0x7fc7e400000 (irq = 17) is a SAB82532 V3.2 [ 70.690261] f00a9ce8: ttyS3 at MMIO 0x7fc7e400040 (irq = 17) is a SAB82532 V3.2 [ 70.697708] Uniform Multi-Platform E-IDE driver [ 70.701972] ide-gd driver 1.18 [ 70.706573] mice: PS/2 mouse device common for all mice [ 70.711785] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0 [ 70.717086] rtc0: no alarms, 114 bytes nvram [ 70.723565] TCP cubic registered [ 70.729616] NET: Registered protocol family 10 [ 70.737775] Mobile IPv6 [ 70.743937] NET: Registered protocol family 17 [ 70.750695] registered taskstats version 1 [ 70.757818] rtc_cmos rtc_cmos: setting system clock to 2012-03-28 17:17:23 UTC (1332955043) [ 70.772777] Initalizing network drop monitor service [ 70.837703] udev[70]: starting version 164 [ 70.923744] SCSI subsystem initialized [ 70.945009] cassini.c:v1.6 (21 May 2008) [ 70.953492] PCI: Enabling device: (0002:00:02.0), cmd 146 [ 70.956740] cassini: MAC address not found in ROM VPD [ 70.967597] eth0: Sun Cassini+ (64bit/33MHz PCI/Cu) Ethernet[19] 08:00:20:9a:b0:e3 [ 70.985601] QLogic Fibre Channel HBA Driver: 8.03.01-k6 [ 70.985657] PCI: Enabling device: (0003:00:01.0), cmd 146 [ 70.988814] cassini: MAC address not found in ROM VPD [ 70.991286] eth1: Sun Cassini+ (64bit/66MHz PCI/Cu) Ethernet[24] 08:00:20:ad:d1:66 [ 71.019705] usbcore: registered new interface driver usbfs [ 71.019947] usbcore: registered new interface driver hub [ 71.021466] usbcore: registered new device driver usb [ 71.046120] qla2xxx 0001:00:01.0: Found an ISP2422, irq 8, iobase 0x000007fd00100000 [ 71.063624] qla2xxx 0001:00:01.0: Configuring PCI space... [ 71.072721] libata version 3.00 loaded. [ 71.077865] PCI: Enabling device: (0000:00:06.0), cmd 5 [ 71.077880] pata_cmd64x 0000:00:06.0: Secondary port is disabled [ 71.084852] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 71.090105] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 71.090166] ohci_hcd 0002:00:01.3: OHCI Host Controller [ 71.090241] ohci_hcd 0002:00:01.3: new USB bus registered, assigned bus number 1 [ 71.090315] ohci_hcd 0002:00:01.3: irq 18, io mem 0x7fc01000000 [ 71.120727] qla2xxx 0001:00:01.0: Configure NVRAM parameters... [ 71.149243] scsi1 : pata_cmd64x [ 71.149320] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 [ 71.149328] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 71.149334] usb usb1: Product: OHCI Host Controller [ 71.149339] usb usb1: Manufacturer: Linux 2.6.32-5-sparc64-smp ohci_hcd [ 71.149345] usb usb1: SerialNumber: 0002:00:01.3 [ 71.149567] usb usb1: configuration #1 chosen from 1 choice [ 71.149681] hub 1-0:1.0: USB hub found [ 71.149714] hub 1-0:1.0: 4 ports detected [ 71.160976] qla2xxx 0001:00:01.0: Verifying loaded RISC code... [ 71.176770] qla2xxx 0001:00:01.0: firmware: requesting ql2400_fw.bin [ 71.186523] qla2xxx 0001:00:01.0: FW: Loading via request-firmware... [ 71.266985] scsi2 : pata_cmd64x [ 71.275942] ata1: PATA max UDMA/33 cmd 0x7ffef000400 ctl 0x7ffef000418 bmdma 0x7ffef000420 irq 6 [ 71.293473] ata2: DUMMY [ 71.302204] pata_cmd64x: active 10 recovery 10 setup 3. [ 71.302229] pata_cmd64x: active 10 recovery 10 setup 3. [ 71.404753] qla2xxx 0001:00:01.0: Allocated (64 KB) for EFT... [ 71.413637] qla2xxx 0001:00:01.0: Allocated (1285 KB) for firmware dump... [ 71.436833] scsi0 : qla2xxx [ 71.446114] qla2xxx 0001:00:01.0: [ 71.446117] QLogic Fibre Channel HBA Driver: 8.03.01-k6 [ 71.446121] QLogic QLA2460 - SG-(X)PCI1FC-QF4, Sun StorageTek 4 Gb FC Enterprise PCI-X Single Channel Host B [ 71.446127] ISP2422: PCI (66 MHz) @ 0001:00:01.0 hdma-, host#=0, fw=4.04.05 (482) [ 71.476740] usb 1-1: new full speed USB device using ohci_hcd and address 2 [ 71.483331] ata1.00: ATAPI: TOSHIBA DVD-ROM SD-C2612, 1011, max UDMA/33 [ 71.483382] pata_cmd64x: active 3 recovery 1 setup 1. [ 71.513806] ata1.00: configured for UDMA/33 [ 71.516608] scsi: waiting for bus probes to complete ... [ 71.533659] PCI: Enabling device: (0003:00:02.0), cmd 3 [ 71.533678] qla2xxx 0003:00:02.0: Found an ISP2200, irq 28, iobase 0x000007fb00400000 [ 71.552320] qla2xxx 0003:00:02.0: Configuring PCI space... [ 71.561884] qla2xxx 0003:00:02.0: Configure NVRAM parameters... [ 71.629492] usb 1-1: New USB device found, idVendor=0557, idProduct=8021 [ 71.639088] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 71.649100] usb 1-1: configuration #1 chosen from 1 choice [ 71.659649] hub 1-1:1.0: USB hub found [ 71.666518] qla2xxx 0003:00:02.0: Inconsistent NVRAM detected: checksum=0x0 id=я version=0xff. [ 71.666525] qla2xxx 0003:00:02.0: Falling back to functioning (yet invalid -- WWPN) defaults. [ 71.666544] qla2xxx 0003:00:02.0: Verifying loaded RISC code... [ 71.680764] qla2xxx 0003:00:02.0: firmware: requesting ql2200_fw.bin [ 71.728735] hub 1-1:1.0: 4 ports detected [ 72.029487] usb 1-1.1: new low speed USB device using ohci_hcd and address 3 [ 72.209945] usb 1-1.1: New USB device found, idVendor=0557, idProduct=2261 [ 72.220440] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 72.240484] usb 1-1.1: Product: CS1716A V1.0.098 [ 72.250417] usb 1-1.1: Manufacturer: ATEN International Co. Ltd [ 72.260344] usb 1-1.1: configuration #1 chosen from 1 choice [ 72.306377] usbcore: registered new interface driver hiddev [ 72.335984] input: ATEN International Co. Ltd CS1716A V1.0.098 as /devices/root/f00806fc/pci0002:00/0002:00:01.3/usb1/1-1/1-1.1/1-1.1:1.0/input/input0 [ 72.355750] generic-usb 0003:0557:2261.0001: input,hidraw0: USB HID v1.00 Keyboard [ATEN International Co. Ltd CS1716A V1.0.098] on usb-0002:00:01.3-1.1/input0 [ 72.413701] input: ATEN International Co. Ltd CS1716A V1.0.098 as /devices/root/f00806fc/pci0002:00/0002:00:01.3/usb1/1-1/1-1.1/1-1.1:1.1/input/input1 [ 72.434673] generic-usb 0003:0557:2261.0002: input,hidraw1: USB HID v1.00 Device [ATEN International Co. Ltd CS1716A V1.0.098] on usb-0002:00:01.3-1.1/input1 [ 72.471103] input: ATEN International Co. Ltd CS1716A V1.0.098 as /devices/root/f00806fc/pci0002:00/0002:00:01.3/usb1/1-1/1-1.1/1-1.1:1.2/input/input2 [ 72.492901] generic-usb 0003:0557:2261.0003: input,hidraw2: USB HID v1.10 Mouse [ATEN International Co. Ltd CS1716A V1.0.098] on usb-0002:00:01.3-1.1/input2 [ 72.514597] usbcore: registered new interface driver usbhid [ 72.525342] usbhid: v2.6:USB HID core driver [ 76.483084] scsi 1:0:0:0: CD-ROM TOSHIBA DVD-ROM SD-C2612 1011 PQ: 0 ANSI: 5 [ 76.538781] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray [ 76.549776] Uniform CD-ROM driver Revision: 3.20 [ 76.561310] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 76.575038] sr 1:0:0:0: Attached scsi generic sg0 type 5 [ 82.392801] qla2xxx 0003:00:02.0: Allocated (252 KB) for firmware dump... [ 82.544735] qla2xxx 0003:00:02.0: LIP reset occurred (f8ef). [ 82.555828] scsi3 : qla2xxx [ 82.567395] qla2xxx 0003:00:02.0: [ 82.567398] QLogic Fibre Channel HBA Driver: 8.03.01-k6 [ 82.567402] QLogic QLA22xx - [ 82.567404] ISP2200: PCI (66 MHz) @ 0003:00:02.0 hdma-, host#=3, fw=2.02.08 TP [ 82.587611] qla2xxx 0003:00:02.0: LIP occurred (f8ef). [ 82.591226] qla2xxx 0003:00:02.0: LOOP UP detected (1 Gbps). [ 82.596585] scsi 3:0:0:0: Direct-Access SEAGATE ST373307FSUN72G 0307 PQ: 0 ANSI: 3 [ 82.600278] scsi 3:0:1:0: Direct-Access SEAGATE ST373307FSUN72G 0307 PQ: 0 ANSI: 3 [ 82.601385] scsi 3:0:0:0: Attached scsi generic sg1 type 0 [ 82.602201] scsi 3:0:1:0: Attached scsi generic sg2 type 0 [ 82.769857] sd 3:0:0:0: [sda] 143374738 512-byte logical blocks: (73.4 GB/68.3 GiB) [ 82.771338] sd 3:0:1:0: [sdb] 143374738 512-byte logical blocks: (73.4 GB/68.3 GiB) [ 82.773633] sd 3:0:1:0: [sdb] Write Protect is off [ 82.773641] sd 3:0:1:0: [sdb] Mode Sense: db 00 10 08 [ 82.777568] sd 3:0:1:0: [sdb] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 82.786705] sdb: sdb2 sdb3 [ 82.848080] sd 3:0:0:0: [sda] Write Protect is off [ 82.857512] sd 3:0:0:0: [sda] Mode Sense: db 00 10 08 [ 82.859985] sd 3:0:1:0: [sdb] Attached SCSI disk [ 82.860055] sd 3:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA [ 82.895420] sda: sda1 sda2 sda3 [ 82.924108] sd 3:0:0:0: [sda] Attached SCSI disk [ 83.258074] md: raid1 personality registered for level 1 [ 83.296862] mdadm: sending ioctl 20001261 to a partition! [ 83.315047] mdadm: sending ioctl 20001261 to a partition! [ 83.325865] mdadm: sending ioctl 20001261 to a partition! [ 83.335127] mdadm: sending ioctl 20001261 to a partition! [ 83.345561] mdadm: sending ioctl 20001261 to a partition! [ 83.353946] mdadm: sending ioctl 20001261 to a partition! [ 83.364579] mdadm: sending ioctl 20001261 to a partition! [ 83.372003] mdadm: sending ioctl 20001261 to a partition! [ 83.395696] mdadm: sending ioctl 20001261 to a partition! [ 83.402547] mdadm: sending ioctl 20001261 to a partition! [ 83.418406] md: md0 stopped. [ 83.445185] md: bind<sdb2> [ 83.453264] md: bind<sda2> [ 83.462632] raid1: raid set md0 active with 2 out of 2 mirrors [ 83.469273] md0: detected capacity change from 0 to 73002967040 [ 83.478217] md0: unknown partition table [ 84.014099] EXT4-fs (md0): mounted filesystem with ordered data mode [ 85.224795] udev[246]: starting version 164 [ 86.783925] loop: module loaded [ 87.654547] kjournald starting. Commit interval 5 seconds [ 87.670500] EXT3 FS on sda1, internal journal [ 87.678218] EXT3-fs: mounted filesystem with ordered data mode. [ 88.134396] ip_tables: (C) 2000-2006 Netfilter Core Team [ 88.403159] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 88.412336] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use [ 88.428120] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or [ 88.444628] sysctl net.netfilter.nf_conntrack_acct=1 to enable it. [ 88.897983] eth1: Link up at 1000 Mbps, full-duplex. [ 88.906735] eth1: Pause is enabled (rxfifo: 16384 off: 13312 on: 11776)