Dear Paul >> On most occasions when this bug has arisen I have been able to log in >> and everything loads fine. > > Could you describe what happens? So GDM default background with no > window, then you enter your credentials and hit enter. Then what. The > background is loaded and fades in and after some time the GNOME panel > appears?
Yes, I get the default background with no visible window to enter my credentials. However I am able to press enter and type in my password to log in as if the credentials window were still there. After entering my password and hitting enter everything appears to load normally just as you say. >> Here is the output from xrandr you wanted. > > […] > > Thanks! It does not show anything weird. Could you please clarify how > you captured this output? After logging in, when everything was fine? Yes, the xrandr output I included was captured from a terminal after logging in normally. I have just experienced this bug again and have included new xrandr output. Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 VGA1 disconnected (normal left inverted right x axis y axis) Identifier: 0x41 Timestamp: 81505 Subpixel: unknown Clones: CRTCs: 0 1 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: LVDS1 connected 1366x768+0+0 (0x45) normal (normal left inverted right x axis y axis) 344mm x 194mm Identifier: 0x42 Timestamp: 81505 Subpixel: horizontal rgb Gamma: 1.0:1.0:1.0 Brightness: 1.0 Clones: CRTC: 1 CRTCs: 1 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: EDID: 00ffffffffffff0030e4300200000000 00130103802213780a62259f5d579b25 19505400000001010101010101010101 0101010101013e1c56a0500016303020 350058c2100000190000000000000000 00000000000000000000000000fe004c 4720446973706c61790a2020000000fc 004c503135365748322d544c41410038 BACKLIGHT: 7 (0x00000007) range: (0,7) Backlight: 7 (0x00000007) range: (0,7) scaling mode: Full supported: None Full Center Full aspect 1366x768 (0x45) 72.3MHz -HSync -VSync *current +preferred h: width 1366 start 1414 end 1446 total 1526 skew 0 clock 47.4KHz v: height 768 start 771 end 776 total 790 clock 60.0Hz 1360x768 (0x46) 84.8MHz -HSync +VSync h: width 1360 start 1432 end 1568 total 1776 skew 0 clock 47.7KHz v: height 768 start 771 end 781 total 798 clock 59.8Hz 1360x768 (0x47) 72.0MHz +HSync -VSync h: width 1360 start 1408 end 1440 total 1520 skew 0 clock 47.4KHz v: height 768 start 771 end 781 total 790 clock 60.0Hz 1024x768 (0x48) 65.0MHz -HSync -VSync h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.4KHz v: height 768 start 771 end 777 total 806 clock 60.0Hz 800x600 (0x49) 40.0MHz +HSync +VSync h: width 800 start 840 end 968 total 1056 skew 0 clock 37.9KHz v: height 600 start 601 end 605 total 628 clock 60.3Hz 800x600 (0x4a) 36.0MHz +HSync +VSync h: width 800 start 824 end 896 total 1024 skew 0 clock 35.2KHz v: height 600 start 601 end 603 total 625 clock 56.2Hz 640x480 (0x4b) 25.2MHz -HSync -VSync h: width 640 start 656 end 752 total 800 skew 0 clock 31.5KHz v: height 480 start 490 end 492 total 525 clock 59.9Hz DP1 disconnected (normal left inverted right x axis y axis) Identifier: 0x43 Timestamp: 81505 Subpixel: unknown Clones: CRTCs: 0 1 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: TV1 disconnected (normal left inverted right x axis y axis) Identifier: 0x44 Timestamp: 81505 Subpixel: unknown Clones: CRTCs: 0 1 Transform: 1.000000 0.000000 0.000000 0.000000 1.000000 0.000000 0.000000 0.000000 1.000000 filter: bottom margin: 37 (0x00000025) range: (0,100) right margin: 46 (0x0000002e) range: (0,100) top margin: 36 (0x00000024) range: (0,100) left margin: 54 (0x00000036) range: (0,100) mode: NTSC-M supported: NTSC-M NTSC-443 NTSC-J PAL-M PAL-N PAL 480p@59.94Hz 480p@60Hz 576p 720p@60Hz 720p@59.94Hz 720p@50Hz 1080i@50Hz 1080i@60Hz 1080i@59.94H > Please make sure to always note the current circumstances when capturing > something as it is very hard otherwise to comprehend what is going on. > > Also please attach the output under system information of `reportbug > gdm` or `reportbug gdm3`. My apologies but I do not know what you are referring to? -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org