Package: src:linux
Version: 3.9.6-1
Severity: normal
Dear Maintainer,
After upgrading from 3.2 to 3.9 windfarm modules break to work. The cooler
speeds are not regulated so after some time their speed is set up to maximum by
hw.
All files from /sys/devices/platform/windfarm.0/ shows 0 RPM. The only file
that shows anything is slots-power and reading from it slows down the fans for
several seconds. Then they are forced to max speed again.
/sys/devices/platform/windfarm.0# ls -al
итого 0
drwxr-xr-x 3 root root 0 июн 24 07:36 .
drwxr-xr-x 13 root root 0 июн 24 07:35 ..
-rw-r--r-- 1 root root 4096 июн 24 07:44 backside-fan
-rw-r--r-- 1 root root 4096 июн 24 07:44 cpufreq-clamp
-rw-r--r-- 1 root root 4096 июн 24 07:44 cpu-front-fan-0
-rw-r--r-- 1 root root 4096 июн 24 07:44 cpu-front-fan-1
-rw-r--r-- 1 root root 4096 июн 24 07:44 cpu-pump-0
-rw-r--r-- 1 root root 4096 июн 24 07:44 cpu-rear-fan-0
-rw-r--r-- 1 root root 4096 июн 24 07:44 cpu-rear-fan-1
-rw-r--r-- 1 root root 4096 июн 24 07:44 drive-bay-fan
lrwxrwxrwx 1 root root 0 июн 24 07:36 driver ->
.../../../bus/platform/drivers/windfarm
-r--r--r-- 1 root root 4096 июн 24 07:44 modalias
drwxr-xr-x 2 root root 0 июн 24 07:44 power
-rw-r--r-- 1 root root 4096 июн 24 07:44 slots-fan
-r--r--r-- 1 root root 4096 июн 24 07:44 slots-power
lrwxrwxrwx 1 root root 0 июн 24 07:36 subsystem -> ../../../bus/platform
-rw-r--r-- 1 root root 4096 июн 24 07:36 uevent
/sys/devices/platform/windfarm.0# lsmod | grep windfarm
windfarm_cpufreq_clamp 4001 1
windfarm_max6690_sensor 4851 0
windfarm_lm75_sensor 5313 0
windfarm_smu_sensors 7691 1
windfarm_smu_controls 7954 8
windfarm_pm112 14588 0
windfarm_smu_sat 8260 1 windfarm_pm112
windfarm_pid 3975 1 windfarm_pm112
windfarm_core 11909 7
windfarm_cpufreq_clamp,windfarm_pm112,windfarm_smu_sensors,windfarm_smu_sat,windfarm_lm75_sensor,windfarm_max6690_sensor,windfarm_smu_controls
-- Package-specific info:
** Version:
Linux version 3.9-1-powerpc64 (debian-ker...@lists.debian.org) (gcc version
4.7.3 (Debian 4.7.3-4) ) #1 SMP Debian 3.9.6-1
** Command line:
root=UUID=a42a8274-d222-4616-9872-c8a93b0b138e ro quiet
** Not tainted
** Kernel log:
[ 7.253379] nouveau [ VBIOS][0000:0a:00.0] ... signature not found
[ 7.253383] nouveau [ VBIOS][0000:0a:00.0] checking ACPI for image...
[ 7.253388] nouveau [ VBIOS][0000:0a:00.0] ... signature not found
[ 7.253392] nouveau [ VBIOS][0000:0a:00.0] checking PCIROM for image...
[ 7.253456] nouveau [ VBIOS][0000:0a:00.0] ... signature not found
[ 7.253463] nouveau [ VBIOS][0000:0a:00.0] checking PLATFORM for image...
[ 7.253468] nouveau [ VBIOS][0000:0a:00.0] ... signature not found
[ 7.253473] nouveau [ VBIOS][0000:0a:00.0] using image from OpenFirmware
[ 7.253525] nouveau [ VBIOS][0000:0a:00.0] BIT signature found
[ 7.253531] nouveau [ VBIOS][0000:0a:00.0] version 05.43.02.75.00
[ 7.253845] nouveau [ PFB][0000:0a:00.0] RAM type: DDR1
[ 7.253849] nouveau [ PFB][0000:0a:00.0] RAM size: 256 MiB
[ 7.253854] nouveau [ PFB][0000:0a:00.0] ZCOMP: 378880 tags
[ 7.300159] nouveau [ PTHERM][0000:0a:00.0] FAN control: toggle
[ 7.300179] nouveau [ PTHERM][0000:0a:00.0] fan management: disabled
[ 7.300185] nouveau [ PTHERM][0000:0a:00.0] internal sensor: no
[ 7.319993] nouveau [ PTHERM][0000:0a:00.0] programmed thresholds [ 90(2),
95(3), 145(2), 135(5) ]
[ 7.320077] nouveau 0000:0a:00.0: Using 32-bit DMA via iommu
[ 7.320170] [TTM] Zone kernel: Available graphics memory: 2010118 kiB
[ 7.320177] [TTM] Initializing pool allocator
[ 7.320211] nouveau [ DRM] VRAM: 252 MiB
[ 7.320215] nouveau [ DRM] GART: 512 MiB
[ 7.320233] nouveau [ DRM] TMDS table version 1.1
[ 7.320237] nouveau [ DRM] DCB version 3.0
[ 7.320246] nouveau [ DRM] DCB outp 00: 01000100 00000028
[ 7.320251] nouveau [ DRM] DCB outp 01: 03000102 00000000
[ 7.320256] nouveau [ DRM] DCB outp 02: 04011210 00000028
[ 7.320260] nouveau [ DRM] DCB outp 03: 02111212 02000100
[ 7.320264] nouveau [ DRM] DCB outp 04: 02011211 0020c070
[ 7.320269] nouveau [ DRM] DCB conn 00: 1030
[ 7.320273] nouveau [ DRM] DCB conn 01: 2130
[ 7.321843] nouveau [ I2C][0000:0a:00.0] detected TMDS transmitter:
sil164
[ 7.387890] sil164 2-0038: Detected device 1:6.0
[ 7.390643] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 7.390646] [drm] No driver support for vblank timestamp query.
[ 7.390654] nouveau [ DRM] 0x14C5: Parsing digital output script table
[ 7.440720] nouveau [ DRM] 1 available performance level(s)
[ 7.440730] nouveau [ DRM] 0: core 300MHz shader 300MHz memory 500MHz
fanspeed 100%
[ 7.440736] nouveau [ DRM] c: core 300MHz shader 300MHz memory 500MHz
fanspeed 100%
[ 7.444056] nouveau [ DRM] MM: using M2MF for buffer copies
[ 7.444076] nouveau [ DRM] Setting dpms mode 3 on TV encoder (output 4)
[ 7.523779] nouveau [ DRM] allocated 1680x1050 fb: 0x9000, bo
c00000017af9e400
[ 7.534311] nouveau [ DRM] 0x14C5: Parsing digital output script table
[ 7.583873] Console: switching to colour frame buffer device 210x65
[ 7.585463] nouveau 0000:0a:00.0: fb0: nouveaufb frame buffer device
[ 7.585467] nouveau 0000:0a:00.0: registered panic notifier
[ 7.585475] [drm] Initialized nouveau 1.1.0 20120801 for 0000:0a:00.0 on
minor 0
[ 7.761878] media: Linux media interface: v0.10
[ 7.823559] Linux video capture interface: v2.00
[ 7.891566] uvcvideo: Found UVC 1.00 device <unnamed> (046d:081d)
[ 7.905201] input: UVC Camera (046d:081d) as
/devices/pci0001:00/0001:00:08.0/0001:01:0b.2/usb3/3-1/3-1:1.2/input/input2
[ 7.905332] usbcore: registered new interface driver uvcvideo
[ 7.905336] USB Video Class driver (1.1.1)
[ 8.187611] set resolution quirk: cval->res = 384
[ 8.187863] usbcore: registered new interface driver snd-usb-audio
[ 13.232420] usb 2-2: New USB device found, idVendor=1131, idProduct=1001
[ 13.232427] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 13.232432] usb 2-2: Product: ISSCBTA
[ 13.353734] Bluetooth: Core ver 2.16
[ 13.353770] NET: Registered protocol family 31
[ 13.353773] Bluetooth: HCI device and connection manager initialized
[ 13.354061] Bluetooth: HCI socket layer initialized
[ 13.354067] Bluetooth: L2CAP socket layer initialized
[ 13.354077] Bluetooth: SCO socket layer initialized
[ 13.395843] usbcore: registered new interface driver btusb
[ 14.263874] Adding 5859368k swap on /dev/sdb3. Priority:-1 extents:1
across:5859368k
[ 14.288534] EXT4-fs (sdb5): re-mounted. Opts: (null)
[ 14.555603] EXT4-fs (sdb5): re-mounted. Opts: errors=remount-ro
[ 14.805931] fuse init (API version 7.21)
[ 14.938702] loop: module loaded
[ 15.598989] kjournald starting. Commit interval 5 seconds
[ 15.599211] EXT3-fs (sdb4): using internal journal
[ 15.599218] EXT3-fs (sdb4): mounted filesystem with ordered data mode
[ 16.741885] RPC: Registered named UNIX socket transport module.
[ 16.741891] RPC: Registered udp transport module.
[ 16.741893] RPC: Registered tcp transport module.
[ 16.741896] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.803055] FS-Cache: Loaded
[ 16.828767] Key type dns_resolver registered
[ 16.857471] FS-Cache: Netfs 'nfs' registered for caching
[ 16.935774] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[ 20.804692] Bluetooth: RFCOMM TTY layer initialized
[ 20.804715] Bluetooth: RFCOMM socket layer initialized
[ 20.804718] Bluetooth: RFCOMM ver 1.11
[ 20.840987] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 20.840993] Bluetooth: BNEP filters: protocol multicast
[ 20.841009] Bluetooth: BNEP socket layer initialized
[ 21.252588] lp: driver loaded but no devices found
[ 21.920116] u3msi: allocated virq 0x19 (hw 0x8) addr 0xfee00000
[ 21.960658] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 22.000612] u3msi: allocated virq 0x1a (hw 0x9) addr 0xfee00000
[ 22.027863] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 25.069300] tg3 0001:05:04.0 eth0: Link is up at 1000 Mbps, full duplex
[ 25.069307] tg3 0001:05:04.0 eth0: Flow control is on for TX and on for RX
[ 25.069328] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 29.032245] NFS: Registering the id_resolver key type
[ 29.032271] Key type id_resolver registered
[ 29.032275] Key type id_legacy registered
[ 85.784055] compat_ioctl32: unknown ioctl 'V', dir=6, #26 (0xc050561a)
[ 85.790264] compat_ioctl32: unknown ioctl 'V', dir=6, #26 (0xc050561a)
** Model information
revision : 1.1 (pvr 0044 0101)
revision : 1.1 (pvr 0044 0101)
revision : 1.1 (pvr 0044 0101)
revision : 1.1 (pvr 0044 0101)
platform : PowerMac
model : PowerMac11,2
machine : PowerMac11,2
motherboard : PowerMac11,2 MacRISC4 Power Macintosh
** Loaded modules:
nfsv3
nfsv4
parport_pc
lp
parport
bnep
rfcomm
binfmt_misc
nfsd
auth_rpcgss
nfs_acl
nfs
dns_resolver
lockd
fscache
sunrpc
ext3
jbd
loop
fuse
btusb
bluetooth
rfkill
snd_usb_audio
snd_usbmidi_lib
snd_hwdep
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_pcm
snd_seq
snd_seq_device
snd_timer
snd
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_core
videodev
soundcore
snd_page_alloc
media
evdev
joydev
sil164
nouveau
ttm
drm_kms_helper
drm
ext4
crc16
jbd2
mbcache
windfarm_cpufreq_clamp
windfarm_max6690_sensor
windfarm_lm75_sensor
windfarm_smu_sensors
windfarm_smu_controls
windfarm_pm112
windfarm_smu_sat
windfarm_pid
windfarm_core
sd_mod
crc_t10dif
ata_generic
hid_logitech
ff_memless
usbhid
hid
sg
sr_mod
cdrom
firewire_ohci
ehci_pci
ohci_hcd
tg3
ehci_hcd
firewire_core
crc_itu_t
usbcore
usb_common
ptp
pps_core
libphy
sata_svw
** PCI devices:
0000:00:0b.0 PCI bridge [0604]: Apple Inc. CPC945 PCIe Bridge [106b:005b]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=0a, subordinate=0a, sec-latency=0
I/O behind bridge: 00000000-0000ffff
Memory behind bridge: 90000000-afffffff
Prefetchable memory behind bridge: 00000000f1000000-00000000f10fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
0000:0a:00.0 VGA compatible controller [0300]: NVIDIA Corporation NV43 [GeForce
6600] [10de:0141] (rev a2) (prog-if 00 [VGA controller])
Subsystem: NVIDIA Corporation Device [10de:0010]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at a1000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at 90000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at a0000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at a2000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nouveau
0001:00:00.0 Host bridge [0600]: Apple Inc. U4 HT Bridge [106b:0074]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
0001:00:01.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-X bridge
[1166:0130] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:02.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-X bridge
[1166:0130] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Memory behind bridge: fa500000-fa5fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:03.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
0001:00:04.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
0001:00:05.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=08, subordinate=08, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
0001:00:06.0 PCI bridge [0604]: Broadcom BCM5780 [HT2000] PCI-Express Bridge
[1166:0132] (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=09, subordinate=09, sec-latency=32
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
0001:00:07.0 PCI bridge [0604]: Apple Inc. Shasta PCI Bridge [106b:0053]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: fa000000-fa3fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:08.0 PCI bridge [0604]: Apple Inc. Shasta PCI Bridge [106b:0054]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: 80000000-800fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:00:09.0 PCI bridge [0604]: Apple Inc. Shasta PCI Bridge [106b:0055]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=32
Memory behind bridge: fa400000-fa4fffff
Prefetchable memory behind bridge: 00000000-000fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
0001:01:07.0 Unassigned class [ff00]: Apple Inc. Shasta Mac I/O [106b:004f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16, Cache Line Size: 64 bytes
Region 0: Memory at 80000000 (32-bit, non-prefetchable) [size=512K]
Kernel driver in use: macio
0001:01:0b.0 USB controller [0c03]: NEC Corporation OHCI USB Controller
[1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB Controller [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 70
Region 0: Memory at 80082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
0001:01:0b.1 USB controller [0c03]: NEC Corporation OHCI USB Controller
[1033:0035] (rev 43) (prog-if 10 [OHCI])
Subsystem: NEC Corporation USB Controller [1033:0035]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (250ns min, 10500ns max), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 70
Region 0: Memory at 80081000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
0001:01:0b.2 USB controller [0c03]: NEC Corporation uPD72010x USB 2.0
Controller [1033:00e0] (rev 04) (prog-if 20 [EHCI])
Subsystem: NEC Corporation uPD72010x USB 2.0 Controller [1033:00e0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (4000ns min, 8500ns max), Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 70
Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
0001:03:0c.0 IDE interface [0101]: Broadcom K2 SATA [1166:0240] (prog-if 8f
[Master SecP SecO PriP PriO])
Subsystem: Broadcom K2 SATA [1166:0240]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16
Interrupt: pin ? routed to IRQ 18
Region 0: I/O ports at <unassigned> [disabled]
Region 1: I/O ports at <unassigned> [disabled]
Region 2: I/O ports at <unassigned> [disabled]
Region 3: I/O ports at <unassigned> [disabled]
Region 4: I/O ports at <unassigned> [disabled]
Region 5: Memory at fa402000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: sata_svw
0001:03:0d.0 Unassigned class [ff00]: Apple Inc. Shasta IDE [106b:0050]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR+ INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin ? routed to IRQ 38
Region 0: Memory at fa404000 (32-bit, non-prefetchable) [size=16K]
Kernel driver in use: pata-pci-macio
0001:03:0e.0 FireWire (IEEE 1394) [0c00]: Apple Inc. Shasta Firewire
[106b:0052] (prog-if 10 [OHCI])
Subsystem: Apple Inc. Device [106b:5811]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 248 (3000ns min, 6000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 39
Region 0: Memory at fa400000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
0001:05:04.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5780
Gigabit Ethernet [14e4:166a] (rev 03)
Subsystem: Apple Inc. Device [106b:0085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 25
Region 0: Memory at fa530000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fa520000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: tg3
0001:05:04.1 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5780
Gigabit Ethernet [14e4:166a] (rev 03)
Subsystem: Apple Inc. Device [106b:0085]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 16 (16000ns min), Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 26
Region 0: Memory at fa510000 (64-bit, non-prefetchable) [size=64K]
Region 2: Memory at fa500000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at <ignored> [disabled]
Capabilities: <access denied>
Kernel driver in use: tg3
** USB devices:
Bus 001 Device 002: ID 046d:c517 Logitech, Inc. LX710 Cordless Desktop Laser
Bus 002 Device 002: ID 1131:1001 Integrated System Solution Corp. KY-BT100
Bluetooth Adapter
Bus 003 Device 002: ID 046d:081d Logitech, Inc. HD Webcam C510
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: powerpc (ppc64)
Kernel: Linux 3.9-1-powerpc64 (SMP w/4 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.9-1-powerpc64 depends on:
ii debconf [debconf-2.0] 1.5.50
ii initramfs-tools [linux-initramfs-tool] 0.112
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.9-1-powerpc64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.9-1-powerpc64 suggests:
pn debian-kernel-handbook <none>
pn linux-doc-3.9 <none>
pn mkvmlinuz <none>
Versions of packages linux-image-3.9-1-powerpc64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
ii firmware-linux-nonfree 0.38
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.9-1-powerpc64/postinst/ignoring-ramdisk:
linux-image-3.9-1-powerpc64/postinst/missing-firmware-3.9-1-powerpc64:
linux-image-3.9-1-powerpc64/prerm/removing-running-kernel-3.9-1-powerpc64:
true
linux-image-3.9-1-powerpc64/postinst/depmod-error-initrd-3.9-1-powerpc64:
false
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
