Package: src:liux
Version: 3.2.6

Bridging does not work on a BCM5721 card (tg3 kernel module). It works
fine using another, Intel card. It somehow looks like packets are being
filtered or dropped somehow.

To illustrate/debug the problem, I used arping on a different host:

arping -t 00:de:ad:be:ef:00 xx.xx.xx.102

Neither the MAC address nor the IP address exist in the network. This
command sends an ARP request for xx.xx.xx.102 to MAC address
00:de:ad:be:ef:00. The expected behavior would be that this packet is
sent to all hosts in the network (the switch doesn't know the MAC
address, so it floods it to all ports).

If the broadcom card is not in a bridge, everything works: a tcpdump
shows the ARP packets arriving over the interface. No reply is sent, but
that is to be expected. Other hosts also see these packets.

If the broadcom card is added to a bridge, this stops working: tcpdump
simply doesn't show any packets at all (and yes, promiscuous mode was
enabled). With the intel card, this works fine.

The same happens for other packets with MAC addresses different from the
network card, these are somehow dropped/filtered. The bridge can thus
never work, because the host does not see any traffic destined for hosts
on the other end of the bridge.

-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-ker...@lists.debian.org) (gcc version 4.6.3 
(Debian 4.6.3-14) ) #1 SMP Debian 3.2.60-1+deb7u3

** Command line:
BOOT_IMAGE=/vmlinuz-3.2.0-4-amd64 root=/dev/mapper/surat-root ro quiet

** Not tainted

** Kernel log:
[    6.652221] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, 
doesn't support DPO or FUA
[    6.664720] input: Dell Dell USB Keyboard as 
/devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2:1.0/input/input0
[    6.664874] generic-usb 0003:413C:2003.0001: input,hidraw0: USB HID v1.10 
Keyboard [Dell Dell USB Keyboard] on usb-0000:00:1d.1-2/input0
[    6.664898] usbcore: registered new interface driver usbhid
[    6.664902] usbhid: USB HID core driver
[    6.680953]  sdb: sdb1 sdb2 < sdb5 >
[    6.681451] sd 3:0:0:0: [sdb] Attached SCSI disk
[    7.064880] device-mapper: uevent: version 1.0.3
[    7.065384] device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: 
dm-de...@redhat.com
[    7.390953] PM: Starting manual resume from disk
[    7.390959] PM: Hibernation image partition 254:1 present
[    7.390961] PM: Looking for hibernation image.
[    7.391148] PM: Image not found (code -22)
[    7.391153] PM: Hibernation image not present or could not be loaded.
[    7.414642] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: 
(null)
[    8.300756] udevd[335]: starting version 175
[    8.424753] input: Power Button as 
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[    8.424761] ACPI: Power Button [PWRF]
[    8.505806] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    8.540146] ACPI: Requesting acpi_cpufreq
[    8.587854] Floppy drive(s): fd0 is 1.44M
[    8.652438] input: PC Speaker as /devices/platform/pcspkr/input/input2
[    8.710862] EDAC MC: Ver: 2.1.0
[    8.732376] EDAC MC0: Giving out device to 'i3000_edac' 'i3000': DEV 
0000:00:00.0
[    8.732406] EDAC PCI0: Giving out device to module 'i3000_edac' controller 
'EDAC PCI controller': DEV '0000:00:00.0' (POLLED)
[    8.742091] i801_smbus 0000:00:1f.3: can't derive routing for PCI INT B
[    8.742095] i801_smbus 0000:00:1f.3: PCI INT B: no GSI
[    8.757940] intel_rng: FWH not detected
[    8.951414] dcdbas dcdbas: Dell Systems Management Base Driver (version 
5.6.0-3.2)
[    8.959714] iTCO_vendor_support: vendor-support=0
[    8.991436] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.07
[    8.991587] iTCO_wdt: Found a ICH7 or ICH7R TCO device (Version=2, 
TCOBASE=0x0860)
[    8.992347] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[    9.053908] leds_ss4200: no LED devices found
[    9.072826] Error: Driver 'pcspkr' is already registered, aborting...
[   11.608037] floppy0: no floppy controllers found
[   12.775810] EXT4-fs (dm-0): re-mounted. Opts: (null)
[   12.953136] EXT4-fs (dm-0): re-mounted. Opts: errors=remount-ro
[   13.025583] loop: module loaded
[   13.079985] drbd: initialized. Version: 8.3.11 (api:88/proto:86-96)
[   13.079992] drbd: srcversion: F937DCB2E5D83C6CCE4A6C9 
[   13.079996] drbd: registered as block device major 147
[   13.080034] drbd: minor_table @ 0xffff88010a2c9000
[   13.579133] Adding 8220668k swap on /dev/mapper/surat-swap_1.  Priority:-1 
extents:1 across:8220668k 
[   14.095657] EXT4-fs (dm-4): mounted filesystem with ordered data mode. Opts: 
(null)
[   14.121143] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: 
(null)
[   14.162354] EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: 
(null)
[   15.131717] Bridge firewalling registered
[   15.136366] device eth2 entered promiscuous mode
[   15.294742] e1000e 0000:01:00.0: irq 76 for MSI/MSI-X
[   15.396115] e1000e 0000:01:00.0: irq 76 for MSI/MSI-X
[   15.396922] ADDRCONF(NETDEV_UP): eth2: link is not ready
[   15.401885] ADDRCONF(NETDEV_UP): kvm-br0: link is not ready
[   17.368990] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: 
None
[   17.369888] ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[   17.369926] kvm-br0: port 1(eth2) entering forwarding state
[   17.369936] kvm-br0: port 1(eth2) entering forwarding state
[   17.370531] ADDRCONF(NETDEV_CHANGE): kvm-br0: link becomes ready
[   17.488927] ADDRCONF(NETDEV_UP): eth1: link is not ready
[   17.851800] RPC: Registered named UNIX socket transport module.
[   17.851806] RPC: Registered udp transport module.
[   17.851810] RPC: Registered tcp transport module.
[   17.851814] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   17.887071] FS-Cache: Loaded
[   17.924986] FS-Cache: Netfs 'nfs' registered for caching
[   17.939146] Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
[   19.710447] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery 
directory
[   19.731820] NFSD: starting 90-second grace period
[   19.872017] kvm-br0: port 1(eth2) entering forwarding state
[   19.892739] tg3 0000:05:00.0: eth1: Link is up at 1000 Mbps, full duplex
[   19.892745] tg3 0000:05:00.0: eth1: Flow control is off for TX and off for RX
[   19.893331] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[   28.096013] kvm-br0: no IPv6 routers present
[   30.400015] eth1: no IPv6 routers present
[   98.084845] tun: Universal TUN/TAP device driver, 1.6
[   98.084851] tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com>
[   98.113541] device tap0 entered promiscuous mode
[   98.113616] kvm-br0: port 2(tap0) entering forwarding state
[   98.113625] kvm-br0: port 2(tap0) entering forwarding state
[  100.616016] kvm-br0: port 2(tap0) entering forwarding state
[  108.384013] tap0: no IPv6 routers present
[  302.878163] device eth0 entered promiscuous mode
[  314.108157] e1000e: eth2 NIC Link is Down
[  314.108762] kvm-br0: port 1(eth2) entering forwarding state
[  380.079847] ADDRCONF(NETDEV_UP): eth0: link is not ready
[  382.515701] tg3 0000:04:00.0: eth0: Link is up at 1000 Mbps, full duplex
[  382.515709] tg3 0000:04:00.0: eth0: Flow control is off for TX and off for RX
[  382.516387] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[  382.516451] kvm-br0: port 3(eth0) entering forwarding state
[  382.516461] kvm-br0: port 3(eth0) entering forwarding state
[  385.024010] kvm-br0: port 3(eth0) entering forwarding state
[  393.040013] eth0: no IPv6 routers present
[  486.017430] tg3 0000:04:00.0: eth0: Link is down
[  486.018037] kvm-br0: port 3(eth0) entering forwarding state
[  490.784993] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: 
None
[  490.785766] kvm-br0: port 1(eth2) entering forwarding state
[  490.785782] kvm-br0: port 1(eth2) entering forwarding state
[  493.288012] kvm-br0: port 1(eth2) entering forwarding state
[  560.560199] device eth0 left promiscuous mode
[  560.560224] kvm-br0: port 3(eth0) entering disabled state

** Model information
sys_vendor: Dell Computer Corporation
product_name: PowerEdge 850
product_version: 
chassis_vendor: Dell Computer Corporation
chassis_version: 
bios_vendor: Dell Computer Corporation
bios_version: A03
board_vendor: Dell Computer Corporation
board_name: 0FJ365
board_version: A02

** Loaded modules:
tun
autofs4
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
bridge
stp
ext2
drbd
lru_cache
loop
kvm_intel
kvm
snd_pcm
snd_page_alloc
iTCO_wdt
iTCO_vendor_support
acpi_cpufreq
dcdbas
mperf
rng_core
psmouse
snd_timer
i2c_i801
i3000_edac
snd
edac_core
soundcore
i2c_core
evdev
pcspkr
serio_raw
processor
shpchp
thermal_sys
button
ext4
crc16
jbd2
mbcache
dm_mod
sg
usbhid
sd_mod
sr_mod
cdrom
hid
crc_t10dif
ata_generic
megaraid_mbox
megaraid_mm
uhci_hcd
ata_piix
ehci_hcd
libata
e1000e
usbcore
tg3
libphy
scsi_mod
usb_common

** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation E7230/3000/3010 Memory Controller 
Hub [8086:2778]
        Subsystem: Dell Device [1028:01b6]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information: Len=09 <?>
        Kernel driver in use: i3000_edac

00:01.0 PCI bridge [0604]: Intel Corporation E7230/3000/3010 PCI Express Root 
Port [8086:2779] (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fe900000-feafffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [88] Subsystem: Dell Device [1028:01b6]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [90] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4161
        Capabilities: [a0] Express (v1) Root Port (Slot+), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, 
L1 <1us
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- 
TransPend-
                LnkCap: Port #2, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 
<1us, L1 <4us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-
                SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- 
Surprise-
                        Slot #2, PowerLimit 25.000W; Interlock- NoCompl-
                SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- 
LinkChg-
                        Control: AttnInd Off, PwrInd On, Power- Interlock-
                SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ 
Interlock-
                        Changed: MRL- PresDet+ LinkState-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- 
CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=WRR32
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
        Capabilities: [140 v1] Root Complex Link
                Desc:   PortNumber=02 ComponentID=01 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=01 AssocRCRB- 
LinkType=MemMapped LinkValid+
                        Addr:   00000000fed19000
        Kernel driver in use: pcieport

00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 
1 [8086:27d0] (rev 01) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
        Memory behind bridge: fe700000-fe8fffff
        Prefetchable memory behind bridge: 00000000fd000000-00000000fd0fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s 
unlimited, L1 unlimited
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
TransPend-
                LnkCap: Port #1, Speed 2.5GT/s, Width x4, ASPM L0s L1, Latency 
L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ 
DLActive+ BWMgmt- ABWMgmt-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- 
CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4169
        Capabilities: [90] Subsystem: Dell Device [1028:01b6]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
                VC1:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable- ID=0 ArbSelect=Fixed TC/VC=00
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=01 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- 
LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1c.4 PCI bridge [0604]: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI 
Express Port 5 [8086:27e0] (rev 01) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
        I/O behind bridge: 0000d000-0000dfff
        Memory behind bridge: fe500000-fe6fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s 
unlimited, L1 unlimited
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
TransPend-
                LnkCap: Port #5, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency 
L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive+ BWMgmt- ABWMgmt-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- 
CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4171
        Capabilities: [90] Subsystem: Dell Device [1028:01b6]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
                VC1:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable- ID=0 ArbSelect=Fixed TC/VC=00
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=05 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- 
LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1c.5 PCI bridge [0604]: Intel Corporation 82801GR/GH/GHM (ICH7 Family) PCI 
Express Port 6 [8086:27e2] (rev 01) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
        I/O behind bridge: 0000c000-0000cfff
        Memory behind bridge: fe300000-fe4fffff
        Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- <SERR- <PERR-
        BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [40] Express (v1) Root Port (Slot-), MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s 
unlimited, L1 unlimited
                        ExtTag- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 128 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
TransPend-
                LnkCap: Port #6, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency 
L0 <1us, L1 <4us
                        ClockPM- Surprise- LLActRep+ BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive+ BWMgmt- ABWMgmt-
                RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal+ PMEIntEna- 
CRSVisible-
                RootCap: CRSVisible-
                RootSta: PME ReqID 0000, PMEStatus- PMEPending-
        Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
                Address: fee0300c  Data: 4179
        Capabilities: [90] Subsystem: Dell Device [1028:01b6]
        Capabilities: [a0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [100 v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed+ WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
                VC1:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed+ WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable- ID=0 ArbSelect=Fixed TC/VC=00
                        Status: NegoPending- InProgress-
        Capabilities: [180 v1] Root Complex Link
                Desc:   PortNumber=06 ComponentID=02 EltType=Config
                Link0:  Desc:   TargetPort=00 TargetComponent=02 AssocRCRB- 
LinkType=MemMapped LinkValid+
                        Addr:   00000000fed1c001
        Kernel driver in use: pcieport

00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI 
Controller #1 [8086:27c8] (rev 01) (prog-if 00 [UHCI])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 20
        Region 4: I/O ports at ace0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI 
Controller #2 [8086:27c9] (rev 01) (prog-if 00 [UHCI])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin B routed to IRQ 21
        Region 4: I/O ports at acc0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI 
Controller #3 [8086:27ca] (rev 01) (prog-if 00 [UHCI])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 22
        Region 4: I/O ports at aca0 [size=32]
        Kernel driver in use: uhci_hcd

00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI 
Controller [8086:27cc] (rev 01) (prog-if 20 [EHCI])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 20
        Region 0: Memory at feb00400 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [50] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [58] Debug port: BAR=1 offset=00a0
        Kernel driver in use: ehci_hcd

00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 
e1) (prog-if 01 [Subtractive decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Bus: primary=00, secondary=06, subordinate=06, sec-latency=32
        I/O behind bridge: 0000b000-0000bfff
        Memory behind bridge: fe100000-fe2fffff
        Prefetchable memory behind bridge: 00000000fc000000-00000000fcffffff
        Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [50] Subsystem: Dell Device [1028:01b6]

00:1f.0 ISA bridge [0601]: Intel Corporation 82801GB/GR (ICH7 Family) LPC 
Interface Bridge [8086:27b8] (rev 01)
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Capabilities: [e0] Vendor Specific Information: Len=0c <?>

00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE 
Controller [8086:27df] (rev 01) (prog-if 8a [Master SecP PriP])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin A routed to IRQ 0
        Region 0: I/O ports at 01f0 [size=8]
        Region 1: I/O ports at 03f4 [size=1]
        Region 2: I/O ports at 0170 [size=8]
        Region 3: I/O ports at 0374 [size=1]
        Region 4: I/O ports at fc00 [size=16]
        Kernel driver in use: ata_piix

00:1f.2 IDE interface [0101]: Intel Corporation NM10/ICH7 Family SATA 
Controller [IDE mode] [8086:27c0] (rev 01) (prog-if 8f [Master SecP SecO PriP 
PriO])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Latency: 0
        Interrupt: pin C routed to IRQ 20
        Region 0: I/O ports at ac98 [size=8]
        Region 1: I/O ports at ac90 [size=4]
        Region 2: I/O ports at ac80 [size=8]
        Region 3: I/O ports at ac78 [size=4]
        Region 4: I/O ports at ac60 [size=16]
        Region 5: Memory at feb00000 (32-bit, non-prefetchable) [size=1K]
        Capabilities: [70] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot+,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: ata_piix

00:1f.3 SMBus [0c05]: Intel Corporation NM10/ICH7 Family SMBus Controller 
[8086:27da] (rev 01)
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        Interrupt: pin B routed to IRQ 0
        Region 4: I/O ports at 08c0 [size=32]
        Kernel driver in use: i801_smbus

01:00.0 Ethernet controller [0200]: Intel Corporation 82572EI Gigabit Ethernet 
Controller (Copper) [8086:107d] (rev 06)
        Subsystem: Intel Corporation PRO/1000 PT Server Adapter [8086:1084]
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx+
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 76
        Region 0: Memory at fe9e0000 (32-bit, non-prefetchable) [size=128K]
        Region 1: Memory at fe9c0000 (32-bit, non-prefetchable) [size=128K]
        Region 2: I/O ports at ece0 [size=32]
        Capabilities: [c8] Power Management version 2
                Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
                Address: 00000000fee0300c  Data: 41a1
        Capabilities: [e0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns, 
L1 <64us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ 
Unsupported+
                        RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency 
L0 <4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP+ FCP- CmpltTO+ CmpltAbrt+ UnxCmplt+ 
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
        Capabilities: [140 v1] Device Serial Number 00-15-17-ff-ff-a8-05-fa
        Kernel driver in use: e1000e

02:00.0 PCI bridge [0604]: Intel Corporation 6702PXH PCI Express-to-PCI Bridge 
A [8086:032c] (rev 09) (prog-if 00 [Normal decode])
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Bus: primary=02, secondary=03, subordinate=03, sec-latency=32
        Memory behind bridge: fe800000-fe8fffff
        Prefetchable memory behind bridge: 00000000fd000000-00000000fd0fffff
        Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort+ <SERR- <PERR-
        BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
                PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
        Capabilities: [44] Express (v1) PCI/PCI-X Bridge, MSI 00
                DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, 
L1 <1us
                        ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop- BrConfRtry-
                        MaxPayload 128 bytes, MaxReadReq 512 bytes
                DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- 
TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x8, ASPM L0s, Latency L0 
unlimited, L1 unlimited
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk- 
DLActive- BWMgmt- ABWMgmt-
        Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
                Address: 0000000000000000  Data: 0000
        Capabilities: [6c] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0+,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Capabilities: [d8] PCI-X bridge device
                Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv
                Status: Dev=02:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
                Upstream: Capacity=65535 CommitmentLimit=65535
                Downstream: Capacity=65535 CommitmentLimit=65535
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UEMsk:  DLP- SDES- TLP+ FCP- CmpltTO+ CmpltAbrt+ UnxCmplt+ 
RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
        Capabilities: [300 v1] Power Budgeting <?>

03:02.0 RAID bus controller [0104]: LSI Logic / Symbios Logic MegaRAID 
[1000:1960] (rev 01)
        Subsystem: Dell MegaRAID 518 DELL PERC 4/DC RAID Controller [1028:0518]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- 
Stepping- SERR+ FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=slow >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 32, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 19
        Region 0: Memory at fd0f0000 (32-bit, prefetchable) [size=64K]
        Expansion ROM at fe800000 [disabled] [size=64K]
        Capabilities: [80] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
        Kernel driver in use: megaraid

04:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 
Gigabit Ethernet PCI Express [14e4:1659] (rev 11)
        Subsystem: Dell Device [1028:01b6]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at fe5f0000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at <ignored> [disabled]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
                Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
                Read-only fields:
                        [PN] Part number: BCM95721
                        [EC] Engineering changes: 106679-15
                        [SN] Serial number: 0123456789
                        [MN] Manufacture ID: 31 34 65 34
                        [RV] Reserved: checksum bad, 28 byte(s) reserved
                Read/write fields:
                        [YA] Asset tag: XYZ01234567
                        [RW] Read-write area: 107 byte(s) free
                End
        Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
                Address: ba16d02c9c9339f4  Data: ff7d
        Capabilities: [d0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 
unlimited
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 
<4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP+ FCP- CmpltTO+ CmpltAbrt+ UnxCmplt+ 
RxOF- MalfTLP- ECRC+ UnsupReq+ ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [13c v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
        Kernel driver in use: tg3

05:00.0 Ethernet controller [0200]: Broadcom Corporation NetXtreme BCM5721 
Gigabit Ethernet PCI Express [14e4:1659] (rev 11)
        Subsystem: Dell Device [1028:01b6]
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- 
<MAbort- >SERR- <PERR- INTx-
        Latency: 0, Cache Line Size: 64 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: Memory at fe3f0000 (64-bit, non-prefetchable) [size=64K]
        Expansion ROM at <ignored> [disabled]
        Capabilities: [48] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot+,D3cold+)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
        Capabilities: [50] Vital Product Data
                Product Name: Broadcom NetXtreme Gigabit Ethernet Controller
                Read-only fields:
                        [PN] Part number: BCM95721
                        [EC] Engineering changes: 106679-15
                        [SN] Serial number: 0123456789
                        [MN] Manufacture ID: 31 34 65 34
                        [RV] Reserved: checksum bad, 28 byte(s) reserved
                Read/write fields:
                        [YA] Asset tag: XYZ01234567
                        [RW] Read-write area: 107 byte(s) free
                End
        Capabilities: [58] MSI: Enable- Count=1/8 Maskable- 64bit+
                Address: fbdffc0d00ff7d84  Data: 061b
        Capabilities: [d0] Express (v1) Endpoint, MSI 00
                DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 
unlimited
                        ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset-
                DevCtl: Report errors: Correctable- Non-Fatal+ Fatal+ 
Unsupported-
                        RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
                        MaxPayload 128 bytes, MaxReadReq 4096 bytes
                DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr+ 
TransPend-
                LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 
<4us, L1 <64us
                        ClockPM- Surprise- LLActRep- BwNot-
                LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
                        ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
                LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ 
DLActive- BWMgmt- ABWMgmt-
        Capabilities: [100 v1] Advanced Error Reporting
                UESta:  DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
                UEMsk:  DLP- SDES- TLP+ FCP- CmpltTO+ CmpltAbrt+ UnxCmplt+ 
RxOF- MalfTLP- ECRC+ UnsupReq+ ACSViol-
                UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- 
RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
                CESta:  RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
                CEMsk:  RxErr+ BadTLP+ BadDLLP+ Rollover+ Timeout+ NonFatalErr-
                AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
        Capabilities: [13c v1] Virtual Channel
                Caps:   LPEVC=0 RefClk=100ns PATEntryBits=1
                Arb:    Fixed- WRR32- WRR64- WRR128-
                Ctrl:   ArbSelect=Fixed
                Status: InProgress-
                VC0:    Caps:   PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
                        Arb:    Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
                        Ctrl:   Enable+ ID=0 ArbSelect=Fixed TC/VC=01
                        Status: NegoPending- InProgress-
        Kernel driver in use: tg3

06:05.0 VGA compatible controller [0300]: XGI Technology Inc. (eXtreme Graphics 
Innovation) Z7/Z9 (XG20 core) [18ca:0020] (prog-if 00 [VGA controller])
        Subsystem: Dell Device [1028:01b6]
        Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop+ ParErr- 
Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- 
<TAbort- <MAbort- >SERR- <PERR- INTx-
        BIST result: 00
        Region 0: Memory at fc000000 (32-bit, prefetchable) [size=16M]
        Region 1: Memory at fe1c0000 (32-bit, non-prefetchable) [size=256K]
        Region 2: I/O ports at bc80 [size=128]
        Expansion ROM at <unassigned> [disabled]
        Capabilities: [40] Power Management version 2
                Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA 
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 413c:2003 Dell Computer Corp. Keyboard


-- System Information:
Debian Release: 7.6
  APT prefers stable-updates
  APT policy: (500, 'stable-updates'), (500, 'stable')
Architecture: i386 (x86_64)

Kernel: Linux 3.2.0-4-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash

Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii  debconf [debconf-2.0]                   1.5.49
ii  initramfs-tools [linux-initramfs-tool]  0.115~bpo70+1
ii  kmod                                    9-3
ii  linux-base                              3.5
ii  module-init-tools                       9-3

Versions of packages linux-image-3.2.0-4-amd64 recommends:
ii  firmware-linux-free  3.2
ii  libc6-i686           2.13-38+deb7u3

Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 1.99-27+deb7u2
pn  linux-doc-3.2           <none>

Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn  firmware-atheros        <none>
pn  firmware-bnx2           <none>
pn  firmware-bnx2x          <none>
pn  firmware-brcm80211      <none>
pn  firmware-intelwimax     <none>
pn  firmware-ipw2x00        <none>
pn  firmware-ivtv           <none>
pn  firmware-iwlwifi        <none>
pn  firmware-libertas       <none>
pn  firmware-linux          <none>
ii  firmware-linux-nonfree  0.36+wheezy.1
pn  firmware-myricom        <none>
pn  firmware-netxen         <none>
pn  firmware-qlogic         <none>
pn  firmware-ralink         <none>
pn  firmware-realtek        <none>
pn  xen-hypervisor          <none>

-- debconf information excluded


-- 
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org

Reply via email to