Package: src:linux Version: 3.16.7-ckt11-1 Severity: normal Dear Maintainer,
i just installed jessie on my cubieboard as described on the debian wiki page. All is fine but I can't see CPU freq: leo@cubetto:~$ cat /proc/cpuinfo processor : 0 model name : ARMv7 Processor rev 2 (v7l) BogoMIPS : 1001.47 Features : swp half thumb fastmult vfp edsp thumbee neon vfpv3 tls vfpd32 CPU implementer : 0x41 CPU architecture: 7 CPU variant : 0x3 CPU part : 0xc08 CPU revision : 2 Hardware : Allwinner A1X (Device Tree) Revision : 0000 Serial : 0000000000000000 and cpufreq is missing: leo@cubetto:~$ ls /sys/devices/system/cpu/cpu0/ crash_notes crash_notes_size online power subsystem topology uevent i've been running wheezy with a 3.4 sunxi kernel for about a year and both CPU speed and cpufreq were there. The kernel config file shows that cpufreq is enabled: leo@cubetto:~$ grep CPU_FREQ /boot/config-3.16.0-4-armmp CONFIG_CPU_FREQ=y Am I missing something? Should I try a more recent kernel? Thanks for supporting such a boad number of ARM boards! -- Package-specific info: ** Version: Linux version 3.16.0-4-armmp (debian-ker...@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt11-1 (2015-05-24) ** Command line: console=ttyS0,115200 quiet ** Not tainted ** Kernel log: [ 1.098504] vcc3v3: disabling [ 1.098510] vcc3v0: disabling [ 1.099738] Freeing unused kernel memory: 684K (c0872000 - c091d000) [ 1.164263] systemd-udevd[55]: starting version 215 [ 1.166032] random: systemd-udevd urandom read with 1 bits of entropy available [ 1.238177] sun4i-emac 1c0b000.ethernet: eth0: at f00a8000, IRQ 17 MAC: 02:97:0a:01:3c:b2 [ 1.259907] sunxi-mmc 1c0f000.mmc: No vqmmc regulator found [ 1.263990] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225. [ 1.278915] SCSI subsystem initialized [ 1.302910] sunxi-mmc 1c0f000.mmc: base:0xf0102000 irq:18 [ 1.330761] libata version 3.00 loaded. [ 1.352014] mmc0: host does not support reading read-only switch. assuming write-enable. [ 1.354031] mmc0: new high speed SDHC card at address b368 [ 1.361425] mmcblk0: mmc0:b368 MSD 7.36 GiB [ 1.364017] mmcblk0: p1 p2 p3 < p5 > [ 1.375526] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP [ 1.375546] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 1.375604] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode [ 1.375619] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 1.385319] scsi0 : ahci_platform [ 1.385771] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 21 [ 1.703443] ata1: SATA link down (SStatus 0 SControl 300) [ 1.743247] PM: Starting manual resume from disk [ 1.743273] PM: Hibernation image partition 179:5 present [ 1.743280] PM: Looking for hibernation image. [ 1.744318] PM: Image not found (code -22) [ 1.744331] PM: Hibernation image not present or could not be loaded. [ 2.096229] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.948522] systemd[1]: Cannot add dependency job for unit display-manager.service, ignoring: Unit display-manager.service failed to load: No such file or directory. [ 3.186035] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro [ 3.423695] systemd-udevd[142]: starting version 215 [ 3.834606] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.847743] ehci-platform: EHCI generic platform driver [ 3.848032] ehci-platform 1c14000.usb: EHCI Host Controller [ 3.848390] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1 [ 3.848529] ehci-platform 1c14000.usb: irq 19, io mem 0x01c14000 [ 3.861876] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00 [ 3.862180] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.862193] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.862203] usb usb1: Product: EHCI Host Controller [ 3.862212] usb usb1: Manufacturer: Linux 3.16.0-4-armmp ehci_hcd [ 3.862220] usb usb1: SerialNumber: 1c14000.usb [ 3.863186] hub 1-0:1.0: USB hub found [ 3.863236] hub 1-0:1.0: 1 port detected [ 3.868687] ehci-platform 1c1c000.usb: EHCI Host Controller [ 3.871857] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2 [ 3.872028] ehci-platform 1c1c000.usb: irq 22, io mem 0x01c1c000 [ 3.881509] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.885245] ohci-platform: OHCI generic platform driver [ 3.885612] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 3.885905] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.885918] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.885928] usb usb2: Product: EHCI Host Controller [ 3.885937] usb usb2: Manufacturer: Linux 3.16.0-4-armmp ehci_hcd [ 3.885945] usb usb2: SerialNumber: 1c1c000.usb [ 3.895746] hub 2-0:1.0: USB hub found [ 3.895817] hub 2-0:1.0: 1 port detected [ 3.899495] ohci-platform 1c14400.usb: Generic Platform OHCI controller [ 3.899880] ohci-platform 1c14400.usb: new USB bus registered, assigned bus number 3 [ 3.900007] ohci-platform 1c14400.usb: irq 20, io mem 0x01c14400 [ 3.963761] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.963781] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.963791] usb usb3: Product: Generic Platform OHCI controller [ 3.963800] usb usb3: Manufacturer: Linux 3.16.0-4-armmp ohci_hcd [ 3.963809] usb usb3: SerialNumber: 1c14400.usb [ 3.964654] hub 3-0:1.0: USB hub found [ 3.964704] hub 3-0:1.0: 1 port detected [ 3.965790] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0) [ 3.966624] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 3.968715] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus number 4 [ 3.968850] ohci-platform 1c1c400.usb: irq 23, io mem 0x01c1c400 [ 4.033257] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 4.033278] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 4.033287] usb usb4: Product: Generic Platform OHCI controller [ 4.033296] usb usb4: Manufacturer: Linux 3.16.0-4-armmp ohci_hcd [ 4.033305] usb usb4: SerialNumber: 1c1c400.usb [ 4.044617] hub 4-0:1.0: USB hub found [ 4.046493] hub 4-0:1.0: 1 port detected [ 4.127939] Adding alias for supply acin,(null) -> acin,0-0034 [ 4.127959] Adding alias for supply vin2,(null) -> vin2,0-0034 [ 4.127967] Adding alias for supply vin3,(null) -> vin3,0-0034 [ 4.127974] Adding alias for supply ldo24in,(null) -> ldo24in,0-0034 [ 4.127982] Adding alias for supply ldo3in,(null) -> ldo3in,0-0034 [ 4.127989] Adding alias for supply ldo5in,(null) -> ldo5in,0-0034 [ 4.128188] axp20x 0-0034: AXP20X driver loaded [ 4.133294] random: nonblocking pool is initialized [ 4.484277] EXT4-fs (mmcblk0p1): mounting ext2 file system using the ext4 subsystem [ 4.543105] EXT4-fs (mmcblk0p1): mounted filesystem without journal. Opts: (null) [ 4.565603] Adding 379900k swap on /dev/mmcblk0p5. Priority:-1 extents:1 across:379900k SSFS [ 4.719333] systemd-journald[144]: Received request to flush runtime journal from PID 1 [ 5.123500] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 5.824977] RPC: Registered named UNIX socket transport module. [ 5.824997] RPC: Registered udp transport module. [ 5.825004] RPC: Registered tcp transport module. [ 5.825011] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 5.847566] FS-Cache: Loaded [ 5.897762] FS-Cache: Netfs 'nfs' registered for caching [ 5.960963] Installing knfsd (copyright (C) 1996 o...@monad.swb.de). [ 7.187550] sun4i-emac 1c0b000.ethernet eth0: Link is Up - 100Mbps/Full - flow control rx/tx [ 7.187595] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ** Model information Hardware : Allwinner A1X (Device Tree) Revision : 0000 ** Loaded modules: nfsd auth_rpcgss oid_registry nfs_acl nfs lockd fscache sunrpc i2c_mv64xxx sun4i_ts sunxi_wdt ohci_platform ehci_platform ohci_hcd ehci_hcd leds_gpio autofs4 ext4 crc16 mbcache jbd2 ahci_sunxi libahci_platform libahci libata scsi_mod phy_sun4i_usb sunxi_mmc sun4i_emac ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). source /etc/network/interfaces.d/* # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet dhcp ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 link/ether 02:97:0a:01:3c:b2 brd ff:ff:ff:ff:ff:ff inet 192.168.0.144/24 brd 192.168.0.255 scope global eth0 valid_lft forever preferred_lft forever inet6 fde7:bd6b:2d4a:0:97:aff:fe01:3cb2/64 scope global mngtmpaddr dynamic valid_lft 7081sec preferred_lft 1681sec inet6 fe80::97:aff:fe01:3cb2/64 scope link valid_lft forever preferred_lft forever *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 eth0: 5654267 5531 0 0 0 0 0 0 377651 3192 0 0 0 0 0 0 *** Protocol statistics: Ip: 5270 total packets received 2 with invalid addresses 0 forwarded 0 incoming packets discarded 4016 incoming packets delivered 3114 requests sent out Icmp: 18 ICMP messages received 0 input ICMP message failed. ICMP input histogram: destination unreachable: 18 0 ICMP messages sent 0 ICMP messages failed ICMP output histogram: IcmpMsg: InType3: 18 Tcp: 8 active connections openings 1 passive connection openings 0 failed connection attempts 0 connection resets received 1 connections established 3962 segments received 3058 segments send out 36 segments retransmited 0 bad segments received. 0 resets sent Udp: 20 packets received 0 packets to unknown port received. 0 packet receive errors 20 packets sent UdpLite: TcpExt: 1 TCP sockets finished time wait in fast timer 6 delayed acks sent 2849 packet headers predicted 101 acknowledgments not containing data payload received 302 predicted acknowledgments 36 retransmits in slow start TCPRcvCoalesce: 511 TCPOFOQueue: 517 TCPOrigDataSent: 393 IpExt: InMcastPkts: 16 InOctets: 5536461 OutOctets: 327418 InMcastOctets: 512 InNoECTPkts: 5270 ** PCI devices: ** USB devices: Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 8.1 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable') Architecture: armhf (armv7l) Kernel: Linux 3.16.0-4-armmp (SMP w/1 CPU core) Locale: LANG=it_IT.UTF-8, LC_CTYPE=it_IT.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages linux-image-3.16.0-4-armmp depends on: ii debconf [debconf-2.0] 1.5.56 ii initramfs-tools [linux-initramfs-tool] 0.120 ii kmod 18-3 ii linux-base 3.5 Versions of packages linux-image-3.16.0-4-armmp recommends: pn firmware-linux-free <none> pn irqbalance <none> Versions of packages linux-image-3.16.0-4-armmp suggests: pn debian-kernel-handbook <none> pn fdutils <none> pn linux-doc-3.16 <none> Versions of packages linux-image-3.16.0-4-armmp is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.16.0-4-armmp/postinst/depmod-error-initrd-3.16.0-4-armmp: false linux-image-3.16.0-4-armmp/postinst/mips-initrd-3.16.0-4-armmp: linux-image-3.16.0-4-armmp/prerm/removing-running-kernel-3.16.0-4-armmp: true -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org