Package: yaird Version: 0.0.12-3 Severity: important After a new installation on hppa, the system seemed to boot correctly, but failed to mount /boot and /home directories. Also the eth0 network interface was not brought up automatically.
If I create the initrd using initramfs-tools these problems do not occur. The reason /boot and /home are not mounted is that /dev/sd* is not present. This seems to indicate a problem with udev, which would also explain eth0 not coming up as it needs to be "hotplug detected". Full log attached. Here are some relevant pieces with comments. [...] SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sda: drive cache: write back SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 < sda5 sda6 sda7 > <!-- SCSI devices detected OK, so driver must be loaded --> [...] INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...usbcore: registered new driver usbfs <!-- udev is started, but I guess that as scsi driver and network driver are loaded already, it does not receive events for them and thus does not create device nodes in /dev, and does not "hotplug" eth0 --> usbcore: registered new driver hub ohci_hcd 0000:00:0e.2: OHCI Host Controller ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.2: irq 1, io mem 0xf4007000 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.15-1-parisc-smp ohci_hcd usb usb1: SerialNumber: 0000:00:0e.2 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected udevd[862]: get_netlink_msg: unable to receive kernel netlink message: No buffer space available <!-- not sure about this message, but the same is shown for initramfs-tools --> Linux Tulip driver version 1.1.13 (December 15, 2004) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1000 status 782d advertising 0081. eth0: Digital DS21142/DS21143 Tulip rev 65 at 80001000, 00:10:83:CF:15:A5, IRQ 66. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NS87415: IDE controller at PCI slot 0000:00:0e.0 NS87415: chipset revision 3 NS87415: 100% native mode on irq 7 ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA done. Waiting for /dev to be fully populated...hda: CD-532E-B, ATAPI CD/DVD-ROM drive <!-- Hmm. Looks like things have not really been waiting... --> [...] Checking all file systems. [/sbin/fsck.ext2 (1) -- /boot] fsck.ext2 -a -C0 /dev/sda2 fsck.ext2: No such file or directory while trying to open /dev/sda2 /dev/sda2: The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> [/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -a -C0 /dev/sda7 fsck.ext3: No such file or directory while trying to open /dev/sda7 /dev/sda7: The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> fsck died with exit status 8 File system check failed. A log is being saved in /var/log/fsck/checkfs if that location is writable. Please repair the file system manually. A maintenance shell will now be started. CONTROL-D will terminate this shell and resume system boot. Give root password for maintenance (or type Control-D to continue): Setting kernel variables ... .... done. Will now mount local filesystems. mount: special device /dev/sda2 does not exist mount: special device /dev/sda7 does not exist Mounting local filesystems failed with error code 32. Will now activate swapfile swap. Done activating swapfile swap. <!-- So here we have the failure to mount /boot and /home --> -- System Information: Debian Release: testing/unstable APT prefers unstable APT policy: (500, 'unstable') Architecture: hppa (parisc) Shell: /bin/sh linked to /bin/bash Kernel: Linux 2.6.15-1-parisc-smp Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Versions of packages yaird depends on: ii cpio 2.6-10 GNU cpio -- a program to manage ar ii dash 0.5.3-2 The Debian Almquist Shell ii libc6 2.3.6-1 GNU C Library: Shared libraries an ii libhtml-template-perl 2.8-1 HTML::Template : A module for usin ii libparse-recdescent-perl 1.94.free-1 Generates recursive-descent parser ii perl 5.8.8-2 Larry Wall's Practical Extraction And, because it may be relevant: ii udev 0.084-5 /dev/ and hotplug management daemon yaird recommends no packages. -- no debconf information
Information: No console specified on kernel command line. This is normal. PALO will choose the console currently used by firmware (serial). Command line for kernel: 'root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux' Selected kernel: /vmlinux from partition 2 Selected ramdisk: /initrd.img-2.6.15-1-parisc-smp.yaird from partition 2 ELF32 executable Entry 00100000 first 00100000 n 3 Segment 0 load 00100000 size 2666012 mediaptr 0x1000 Segment 1 load 0038b000 size 513884 mediaptr 0x28c000 Segment 2 load 0040c000 size 396068 mediaptr 0x30a000 Loading ramdisk 1274748 bytes @ 3feb7000... Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org Linux version 2.6.15-1-parisc-smp (Debian 2.6.15-6) ([EMAIL PROTECTED]) (gcc version 4.0.3 20060128 (prerelease) (Debian 4.0.2-8)) #2 SMP Fri Feb 10 23:30:34 GMT 2006 FP[0] enabled: Rev 1 Model 16 The 32-bit Kernel has started... Initialized PDC Console for debugging. Determining PDC firmware type: System Map. model 00005d10 00000491 00000000 00000002 778fe5fc 100000f0 00000008 000000b2 000000b2 vers 00000300 CPUID vers 17 rev 10 (0x0000022a) capabilities 0x3 model 9000/785/J5600 Total Memory: 2048 MB initrd: 4feb7000-4ffee37c initrd: reserving 3feb7000-3ffee37c (mem_max 80000000) LCD display at f05d0008,f05d0000 registered SMP: bootstrap CPU ID is 0 Built 1 zonelists Kernel command line: root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux PID hash table entries: 4096 (order: 12, 65536 bytes) Console: colour dummy device 160x64 Dentry cache hash table entries: 524288 (order: 9, 2097152 bytes) Inode-cache hash table entries: 262144 (order: 8, 1048576 bytes) Memory: 2097152k available Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 512 Brought up 1 CPUs checking if image is initramfs... it is NET: Registered protocol family 16 EISA bus registered Searching for devices... Found devices: 1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } 2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } 3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } 4. Elroy PCI Bridge at 0xfed34000 [10/2] { 13, 0x0, 0x782, 0x0000a } 5. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } 6. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } 7. Forte W+ 2w at 0xfffa0000 [32] { 0, 0x0, 0x5d1, 0x00004 } 8. Forte W+ 2w at 0xfffa2000 [34] { 0, 0x0, 0x5d1, 0x00004 } 9. Memory at 0xfed10200 [49] { 1, 0x0, 0x09e, 0x00009 } Releasing cpu 1 now, hpa=fffa2000 FP[1] enabled: Rev 1 Model 16 CPU(s): 2 x PA8600 (PCX-W+) at 552.000000 MHz Setting cache flush threshold to 700 (2 CPUs online) SBA found Astro 2.1 at 0xfed00000 LBA version TR2.1 (0x2) found at 0xfed30000 PCI: Enabled native mode for NS87415 (pif=0x8f) LBA version TR2.1 (0x2) found at 0xfed32000 LBA version TR2.1 (0x2) found at 0xfed34000 LBA version TR2.1 (0x2) found at 0xfed38000 LBA version TR2.1 (0x2) found at 0xfed3c000 TC classifier action (bugs to netdev@vger.kernel.org cc [EMAIL PROTECTED]) unwind_init: start = 0x1038ca70, end = 0x103aec80, entries = 8737 audit: initializing netlink socket (disabled) audit(1140292946.610:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 68) SuperIO: Serial port 1 at 0x3f8 SuperIO: Serial port 2 at 0x2f8 SuperIO: Parallel port at 0x378 SuperIO: Floppy controller at 0x3f0 SuperIO: ACPI at 0x7e0 SuperIO: USB regulator enabled PDC Stable Storage facility v0.10 Soft power switch enabled, polling @ 0xf0400804. STI GSC/PCI core graphics driver Version 0.9a Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 3) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 4) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 7, 524288 bytes) TCP established hash table entries: 131072 (order: 9, 3145728 bytes) TCP bind hash table entries: 65536 (order: 8, 1310720 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: Badness in smp_call_function at arch/parisc/kernel/smp.c:348 Backtrace: [<10115d04>] smp_call_function+0x78/0x328 [<10106da4>] flush_data_cache+0x20/0x34 [<10105e5c>] free_initmem+0x50/0x1c4 [<101051e8>] init+0x5f0/0xb54 [<1010dc5c>] ret_from_kernel_thread+0x1c/0x24 340k freed SCSI subsystem initialized sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 69 sym0: PA-RISC Firmware, ID 7, Fast-40, SE, parity checking sym0: SCSI BUS has been reset. sym0: SCSI BUS mode change from SE to SE. scsi0 : sym-2.2.2 sym0: SCSI BUS has been reset. sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 69 sym1: PA-RISC Firmware, ID 7, Fast-40, LVD, parity checking sym1: SCSI BUS has been reset. scsi1 : sym-2.2.2 Vendor: HP Model: 9.10GB C 80-CX03 Rev: CX03 Type: Direct-Access ANSI SCSI revision: 02 target1:0:3: tagged command queuing enabled, command queue depth 16. target1:0:3: Beginning Domain Validation target1:0:3: asynchronous. target1:0:3: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 31) target1:0:3: Domain Validation skipping write tests target1:0:3: Ending Domain Validation Vendor: HP Model: 9.10GB C 80-CX03 Rev: CX03 Type: Direct-Access ANSI SCSI revision: 02 target1:0:4: tagged command queuing enabled, command queue depth 16. target1:0:4: Beginning Domain Validation target1:0:4: asynchronous. target1:0:4: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 31) target1:0:4: Domain Validation skipping write tests target1:0:4: Ending Domain Validation Vendor: QUANTUM Model: ATLAS10K-9LVD Rev: HP06 Type: Direct-Access ANSI SCSI revision: 03 target1:0:5: tagged command queuing enabled, command queue depth 16. target1:0:5: Beginning Domain Validation target1:0:5: asynchronous. target1:0:5: FAST-40 SCSI 40.0 MB/s ST (25 ns, offset 31) target1:0:5: Domain Validation skipping write tests target1:0:5: Ending Domain Validation SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sda: drive cache: write back SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 < sda5 sda6 sda7 > sd 1:0:3:0: Attached scsi disk sda SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sdb: drive cache: write back sdb: unknown partition table sd 1:0:4:0: Attached scsi disk sdb SCSI device sdc: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sdc: drive cache: write back SCSI device sdc: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sdc: drive cache: write back sdc: unknown partition table sd 1:0:5:0: Attached scsi disk sdc kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Switching root ... INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...usbcore: registered new driver usbfs usbcore: registered new driver hub ohci_hcd 0000:00:0e.2: OHCI Host Controller ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.2: irq 1, io mem 0xf4007000 usb usb1: Product: OHCI Host Controller usb usb1: Manufacturer: Linux 2.6.15-1-parisc-smp ohci_hcd usb usb1: SerialNumber: 0000:00:0e.2 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected udevd[862]: get_netlink_msg: unable to receive kernel netlink message: No buffer space available Linux Tulip driver version 1.1.13 (December 15, 2004) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1000 status 782d advertising 0081. eth0: Digital DS21142/DS21143 Tulip rev 65 at 80001000, 00:10:83:CF:15:A5, IRQ 66. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx NS87415: IDE controller at PCI slot 0000:00:0e.0 NS87415: chipset revision 3 NS87415: 100% native mode on irq 7 ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:DMA, hdb:DMA ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:DMA, hdd:DMA done. Waiting for /dev to be fully populated...hda: CD-532E-B, ATAPI CD/DVD-ROM drive ide0 at 0xf00-0xf07,0xe02 on irq 7 done. Will now activate swap. swapon on /dev/sda6 swapon: cannot stat /dev/sda6: No such file or directory Swap activation failed with error code 255. Will now check root file system. fsck 1.39-WIP (31-Dec-2005) [/sbin/fsck.ext3 (1) -- /dev/shm/root] fsck.ext3 -a -C0 EXT3 FS on sda5, /internal journal dev/shm/root /: clean, 29425/319360 files, 142871/638575 blocks Done checking root file system. A log will be saved in /var/log/fsck/checkroot if that location is writable. Setting the system clock.. System Clock set. Local time: Sat Feb 18 20:03:06 UTC 2006. Cleaning up ifupdown...done. Calculating module dependencies...done. Loading modules... ide-cd hda: ATAPI 32X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 ide-disk ide-generic lasi700 lasi_82596 zalon7xx All modules loaded. Setting the system clock again.. System Clock set. Local time: Sat Feb 18 20:03:09 UTC 2006. Will now check all file systems. fsck 1.39-WIP (31-Dec-2005) Checking all file systems. [/sbin/fsck.ext2 (1) -- /boot] fsck.ext2 -a -C0 /dev/sda2 fsck.ext2: No such file or directory while trying to open /dev/sda2 /dev/sda2: The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> [/sbin/fsck.ext3 (1) -- /home] fsck.ext3 -a -C0 /dev/sda7 fsck.ext3: No such file or directory while trying to open /dev/sda7 /dev/sda7: The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsck -b 8193 <device> fsck died with exit status 8 File system check failed. A log is being saved in /var/log/fsck/checkfs if that location is writable. Please repair the file system manually. A maintenance shell will now be started. CONTROL-D will terminate this shell and resume system boot. Give root password for maintenance (or type Control-D to continue): Setting kernel variables ... .... done. Will now mount local filesystems. mount: special device /dev/sda2 does not exist mount: special device /dev/sda7 does not exist Mounting local filesystems failed with error code 32. Will now activate swapfile swap. Done activating swapfile swap. Detecting hardware...Discovered hardware for these modules: tulip sym53c8xx ad1889 Skipping already loaded module tulip. Skipping already loaded module sym53c8xx. Skipping unavailable/built-in ad1889 module. Cleaning /tmp...done. Cleaning /var/run...done. Cleaning /var/lock...done. Setting up networking...done. Setting hostname to 'treebeard'...done. Configuring network interfaces...done. Starting portmap daemon: portmap. Initializing random number generator...done. Recovering nvi editor sessions... done. INIT: Entering runlevel: 2 Starting system log daemon: syslogd. Starting kernel log daemon: klogd. Starting MTA: exim4. Starting internet superserver: inetd. Starting printer spooler: lpd . Starting OpenBSD Secure Shell server: sshdNET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver .. Starting NFS common utilities: statd. Starting deferred execution scheduler: atd. Starting periodic command scheduler: cron. Debian GNU/Linux testing/unstable treebeard ttyS0