Package: src:linux
Version: 4.15.11-1
Severity: normal
Tags: upstream
Dear Maintainer,
Today I upgraded from linux-image-4.14.0-3-amd64 to 4.15.0-2-amd64. Because the
third monitor connected via VGA
doesn't seem to expose a proper EDID or any EDID at all, I use
"drm_kms_helper.edid_firmware=VGA-1:edid/1280x1024.bin"
to force the resolution. This used to work fine with the built-in firmwares as
well as with a custom EDID I acquired from
the screen by connecting it to HDMI.
With the upgrade to 4.15.0-2-amd64, the flag doesn't work anymore. The only
relevant message I get in dmesg is:
[ 8.750411] [drm] drm_kms_firmware.edid_firmware is deprecated, please use
drm.edid_firmware intead.
When using the config variable drm.edid_firmware, instead, the deprecation
warning disappears, but still, nothing happens.
"edid-decode /sys/devices/pci0000:00/0000:00:02.0/drm/card0/card0-VGA-1/edid"
now returns an invalid or no EDID:
Extracted contents:
header: 00 00 00 00 00 00 00 00
serial number: 00 00 00 00 00 00 00 00 00 00
version: 00 00
basic params: 00 00 00 00 00
chroma info: 00 00 00 00 00 00 00 00 00 00
established: 00 00 00
standard: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
descriptor 1: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
descriptor 2: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
descriptor 3: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
descriptor 4: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
extensions: 00
checksum: 00
No header found
Manufacturer: @@@ Model 0 Serial Number 0
EDID version: 0.0
Analog display, Input voltage level: 0.7/0.3 V
Sync:
Image size is variable
Gamma: 1.00
Monochrome or grayscale display
Established timings supported:
Standard timings supported:
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
non-conformant standard timing (0 horiz)
Manufacturer-specified data, tag 0
Manufacturer-specified data, tag 0
Manufacturer-specified data, tag 0
Manufacturer-specified data, tag 0
Checksum: 0x0 (valid)
EDID block does not conform at all!
Bad year of manufacture
Manufacturer name field contains garbage
Whereas previously it would display information about the custom EDID.
I have also attached the dmesg of the previous kernel.
-- Package-specific info:
** Version:
Linux version 4.15.0-2-amd64 (debian-ker...@lists.debian.org) (gcc version
7.3.0 (Debian 7.3.0-12)) #1 SMP Debian 4.15.11-1 (2018-03-20)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-4.15.0-2-amd64
root=UUID=78f2fe7c-bc1b-4073-aa07-9ea42b0ab9e0 ro quiet
drm_kms_helper.edid_firmware=VGA-1:edid/1280x1024.bin
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 8.863552] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 8.976735] EFI Variables Facility v0.08 2004-May-17
[ 9.060109] pstore: using zlib compression
[ 9.060124] pstore: Registered efi as persistent store backend
[ 9.131124] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 9.131144] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 9.329121] fbcon: inteldrmfb (fb0) is primary device
[ 9.408147] snd_hda_intel 0000:00:03.0: enabling device (0100 -> 0102)
[ 9.408267] snd_hda_intel 0000:00:1b.0: enabling device (0100 -> 0102)
[ 9.443559] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC221:
line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 9.443561] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=1
(0x17/0x0/0x0/0x0/0x0)
[ 9.443562] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1
(0x21/0x0/0x0/0x0/0x0)
[ 9.443563] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 9.443563] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 9.443565] snd_hda_codec_realtek hdaudioC1D0: Mic=0x1a
[ 9.443566] snd_hda_codec_realtek hdaudioC1D0: Line=0x1b
[ 9.449006] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops
i915_audio_component_bind_ops [i915])
[ 9.449006] Console: switching to colour frame buffer device 128x48
[ 9.466746] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 9.467834] input: HDA Intel HDMI HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input10
[ 9.467851] input: HDA Intel HDMI HDMI/DP,pcm=7 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input11
[ 9.467868] input: HDA Intel HDMI HDMI/DP,pcm=8 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input12
[ 9.467883] input: HDA Intel HDMI HDMI/DP,pcm=9 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input13
[ 9.467901] input: HDA Intel HDMI HDMI/DP,pcm=10 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input14
[ 9.492591] input: HDA Intel PCH Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input15
[ 9.492606] input: HDA Intel PCH Line as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input16
[ 9.492619] input: HDA Intel PCH Line Out as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input17
[ 9.492632] input: HDA Intel PCH Front Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input18
[ 9.844042] input: HP WMI hotkeys as /devices/virtual/input/input19
[ 9.845243] iTCO_vendor_support: vendor-support=0
[ 9.949424] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 9.949472] iTCO_wdt: Found a Lynx Point TCO device (Version=2,
TCOBASE=0x0460)
[ 9.949556] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.760116] intel_rapl: Found RAPL domain package
[ 10.760117] intel_rapl: Found RAPL domain core
[ 10.760118] intel_rapl: Found RAPL domain uncore
[ 10.760118] intel_rapl: Found RAPL domain dram
[ 10.760120] intel_rapl: RAPL package 0 domain package locked by BIOS
[ 10.760123] intel_rapl: RAPL package 0 domain dram locked by BIOS
[ 11.074375] cfg80211: Loading compiled-in X.509 certificates for regulatory
database
[ 11.074552] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 11.173417] usb 3-3: 1:1: cannot get freq at ep 0x83
[ 11.174894] usb 3-3: 2:1: cannot get freq at ep 0x4
[ 11.188865] usbcore: registered new interface driver snd-usb-audio
[ 11.207053] platform regulatory.0: firmware: failed to load regulatory.db
(-2)
[ 11.207088] firmware_class: See https://wiki.debian.org/Firmware for
information about missing firmware
[ 11.207127] platform regulatory.0: Direct firmware load for regulatory.db
failed with error -2
[ 11.207129] cfg80211: failed to load regulatory.db
[ 11.370986] Adding 16686076k swap on /dev/sda3. Priority:-2 extents:1
across:16686076k FS
[ 11.692222] usb 3-4: reset high-speed USB device number 3 using xhci_hcd
[ 11.850861] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201
detected
[ 11.861902] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0006 detected
[ 11.960070] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.960476] usbcore: registered new interface driver rt2800usb
[ 12.013515] rt2800usb 3-4:1.0 wlx00259ca32202: renamed from wlan0
[ 12.111094] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts:
(null)
[ 13.621345] audit: type=1400 audit(1522768368.183:2): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-senddoc"
pid=642 comm="apparmor_parser"
[ 13.677793] audit: type=1400 audit(1522768368.239:3): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-oopslash"
pid=639 comm="apparmor_parser"
[ 13.705333] audit: type=1400 audit(1522768368.267:4): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=637
comm="apparmor_parser"
[ 13.705336] audit: type=1400 audit(1522768368.267:5): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_filter" pid=637
comm="apparmor_parser"
[ 13.705338] audit: type=1400 audit(1522768368.267:6): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_groff" pid=637
comm="apparmor_parser"
[ 13.795625] audit: type=1400 audit(1522768368.355:7): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport"
pid=644 comm="apparmor_parser"
[ 13.863571] audit: type=1400 audit(1522768368.423:8): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed"
pid=646 comm="apparmor_parser"
[ 13.995895] audit: type=1400 audit(1522768368.555:9): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/lib/cups/backend/cups-
pdf" pid=647 comm="apparmor_parser"
[ 13.995897] audit: type=1400 audit(1522768368.555:10): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/sbin/cupsd" pid=647
comm="apparmor_parser"
[ 13.995898] audit: type=1400 audit(1522768368.555:11): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/sbin/cupsd//third_party" pid=647 comm="apparmor_parser"
[ 17.142134] vboxdrv: loading out-of-tree module taints kernel.
[ 17.153332] vboxdrv: Found 4 processor cores
[ 17.172257] vboxdrv: TSC mode is Invariant, tentative frequency 3192606505
Hz
[ 17.172257] vboxdrv: Successfully loaded version 5.1.34 (interface
0x002a0000)
[ 17.639938] VBoxNetFlt: Successfully started.
[ 17.918175] VBoxNetAdp: Successfully started.
[ 18.104258] VBoxPciLinuxInit
[ 18.258373] vboxpci: IOMMU not found (not registered)
[ 19.123619] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading
firmware file 'rt2870.bin'
[ 19.128942] rt2800usb 3-4:1.0: firmware: direct-loading firmware rt2870.bin
[ 19.128947] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware
detected - version: 0.36
[ 19.551015] IPv6: ADDRCONF(NETDEV_UP): wlx00259ca32202: link is not ready
[ 19.762938] IPv6: ADDRCONF(NETDEV_CHANGE): wlx00259ca32202: link becomes
ready
[ 21.650696] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 21.864264] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 25.490230] e1000e: eno1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 25.490262] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[ 34.446625] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 37.437969] kauditd_printk_skb: 13 callbacks suppressed
[ 37.437970] audit: type=1400 audit(1522768391.999:25): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="docker-default" pid=1367
comm="apparmor_parser"
[ 40.846809] bridge: filtering via arp/ip/ip6tables is no longer available by
default. Update your scripts to load br_netfilter if you need this.
[ 40.937287] Bridge firewalling registered
[ 42.357616] Initializing XFRM netlink socket
[ 42.443510] Netfilter messages via NETLINK v0.30.
[ 42.453873] ctnetlink v0.93: registering with nfnetlink.
[ 42.641027] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
[ 47.662982] usb 3-3: 1:1: cannot get freq at ep 0x83
[ 60.685752] Could not find key with description: [a047d98f708ca78a]
[ 60.685755] process_request_key_err: No key
[ 60.685755] Could not find valid key in user session keyring for sig
specified in mount option: [a047d98f708ca78a]
[ 60.685756] One or more global auth toks could not properly register; rc =
[-2]
[ 60.685757] Error parsing options; rc = [-2]
[ 62.555405] fuse init (API version 7.26)
[ 67.837075] rfkill: input handler disabled
** Model information
sys_vendor: Hewlett-Packard
product_name: HP EliteDesk 800 G1 SFF
product_version:
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: L01 v02.71
board_vendor: Hewlett-Packard
board_name: 1998
board_version:
** Loaded modules:
fuse
nf_conntrack_netlink
nfnetlink
xfrm_user
xfrm_algo
xt_addrtype
iptable_filter
xt_conntrack
br_netfilter
bridge
stp
llc
overlay
ipt_MASQUERADE
nf_nat_masquerade_ipv4
iptable_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_nat_ipv4
nf_nat
nf_conntrack
libcrc32c
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
arc4
rt2800usb
rt2x00usb
rt2800lib
rt2x00lib
mac80211
snd_usb_audio
snd_usbmidi_lib
cfg80211
snd_rawmidi
crc_ccitt
intel_rapl
snd_seq_device
joydev
nls_ascii
x86_pkg_temp_thermal
intel_powerclamp
nls_cp437
vfat
fat
coretemp
kvm_intel
iTCO_wdt
kvm
iTCO_vendor_support
hp_wmi
irqbypass
sparse_keymap
rfkill
crct10dif_pclmul
crc32_pclmul
evdev
ghash_clmulni_intel
wmi_bmof
snd_hda_codec_hdmi
snd_hda_codec_realtek
snd_hda_codec_generic
snd_hda_intel
snd_hda_codec
intel_cstate
intel_uncore
sg
snd_hda_core
efi_pstore
efivars
snd_hwdep
snd_pcm
mei_me
mei
lpc_ich
mfd_core
intel_rapl_perf
i915
drm_kms_helper
tpm_infineon
drm
pcspkr
serio_raw
i2c_algo_bit
snd_timer
snd
soundcore
video
button
wmi
ecryptfs
parport_pc
ppdev
lp
parport
efivarfs
ip_tables
x_tables
autofs4
ext4
crc16
mbcache
jbd2
crc32c_generic
fscrypto
ecb
hid_generic
usbhid
hid
sr_mod
cdrom
sd_mod
crc32c_intel
aesni_intel
ahci
libahci
aes_x86_64
crypto_simd
cryptd
glue_helper
psmouse
i2c_i801
ehci_pci
xhci_pci
libata
xhci_hcd
ehci_hcd
e1000e
scsi_mod
ptp
usbcore
pps_core
usb_common
fan
thermal
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 4th Gen Core Processor DRAM
Controller [8086:0c00] (rev 06)
Subsystem: Hewlett-Packard Company 4th Gen Core Processor DRAM
Controller [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: hsw_uncore
00:02.0 VGA compatible controller [0300]: Intel Corporation Xeon E3-1200 v3/4th
Gen Core Processor Integrated Graphics Controller [8086:0412] (rev 06) (prog-if
00 [VGA controller])
Subsystem: Hewlett-Packard Company Xeon E3-1200 v3/4th Gen Core
Processor Integrated Graphics Controller [103c:1998]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: i915
Kernel modules: i915
00:03.0 Audio device [0403]: Intel Corporation Xeon E3-1200 v3/4th Gen Core
Processor HD Audio Controller [8086:0c0c] (rev 06)
Subsystem: Hewlett-Packard Company Xeon E3-1200 v3/4th Gen Core
Processor HD Audio Controller [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at f7c34000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset
Family USB xHCI [8086:8c31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
USB xHCI [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 27
Region 0: Memory at f7c20000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
Kernel modules: xhci_pci
00:16.0 Communication controller [0780]: Intel Corporation 8 Series/C220 Series
Chipset Family MEI Controller #1 [8086:8c3a] (rev 04)
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
MEI Controller [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at f7c40000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
Kernel modules: mei_me
00:16.3 Serial controller [0700]: Intel Corporation 8 Series/C220 Series
Chipset Family KT Controller [8086:8c3d] (rev 04) (prog-if 02 [16550])
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
KT Controller [103c:1998]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at f0e0 [size=8]
Region 1: Memory at f7c3e000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
00:19.0 Ethernet controller [0200]: Intel Corporation Ethernet Connection
I217-LM [8086:153a] (rev 04)
Subsystem: Hewlett-Packard Company Ethernet Connection I217-LM
[103c:1998]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 26
Region 0: Memory at f7c00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7c3d000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
Kernel modules: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset
Family USB EHCI #2 [8086:8c2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
USB EHCI [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7c3c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1b.0 Audio device [0403]: Intel Corporation 8 Series/C220 Series Chipset
High Definition Audio Controller [8086:8c20] (rev 04)
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset High
Definition Audio Controller [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 31
Region 0: Memory at f7c30000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1d.0 USB controller [0c03]: Intel Corporation 8 Series/C220 Series Chipset
Family USB EHCI #1 [8086:8c26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
USB EHCI [103c:1998]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7c3b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
00:1f.0 ISA bridge [0601]: Intel Corporation Q87 Express LPC Controller
[8086:8c4e] (rev 04)
Subsystem: Hewlett-Packard Company Q87 Express LPC Controller
[103c:1998]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
Kernel modules: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 8 Series/C220 Series Chipset
Family 6-port SATA Controller 1 [AHCI mode] [8086:8c02] (rev 04) (prog-if 01
[AHCI 1.0])
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
6-port SATA Controller 1 [AHCI mode] [103c:1998]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 28
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7c3a000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
Kernel modules: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 8 Series/C220 Series Chipset Family
SMBus Controller [8086:8c22] (rev 04)
Subsystem: Hewlett-Packard Company 8 Series/C220 Series Chipset Family
SMBus Controller [103c:1998]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7c39000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
Kernel modules: i2c_i801
** USB devices:
Bus 002 Device 002: ID 8087:8000 Intel Corp.
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:8008 Intel Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 003: ID 1737:0077 Linksys WUSB54GC v3 802.11g Adapter [Ralink
RT2070L]
Bus 003 Device 002: ID 0b0e:0305 GN Netcom
Bus 003 Device 005: ID 03f0:034a Hewlett-Packard Elite Keyboard
Bus 003 Device 004: ID 046d:c077 Logitech, Inc. M105 Optical Mouse
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: buster/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 4.15.0-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8),
LANGUAGE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
LSM: AppArmor: enabled
Versions of packages linux-image-4.15.0-2-amd64 depends on:
ii initramfs-tools [linux-initramfs-tool] 0.130
ii kmod 25-1
ii linux-base 4.5
Versions of packages linux-image-4.15.0-2-amd64 recommends:
ii apparmor 2.12-4
ii firmware-linux-free 3.4
ii irqbalance 1.3.0-0.1
Versions of packages linux-image-4.15.0-2-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-efi-amd64 2.02+dfsg1-3
pn linux-doc-4.15 <none>
Versions of packages linux-image-4.15.0-2-amd64 is related to:
pn firmware-amd-graphics <none>
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-cavium <none>
pn firmware-intel-sound <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux-nonfree <none>
ii firmware-misc-nonfree 20170823-1
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-realtek <none>
pn firmware-samsung <none>
pn firmware-siano <none>
pn firmware-ti-connectivity <none>
pn xen-hypervisor <none>
-- no debconf information
*** /tmp/dmesg_working
[ 0.000000] microcode: microcode updated early to revision 0x24, date =
2018-01-21
[ 0.000000] Linux version 4.14.0-3-amd64 (debian-ker...@lists.debian.org)
(gcc version 7.3.0 (Debian 7.3.0-3)) #1 SMP Debian 4.14.17-1 (2018-02-14)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-4.14.0-3-amd64
root=UUID=78f2fe7c-bc1b-4073-aa07-9ea42b0ab9e0 ro quiet
drm_kms_helper.edid_firmware=VGA-1:edid/1280x1024.bin
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point
registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes,
using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000004efff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000004f000-0x000000000004ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000050000-0x000000000009dfff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000c652afff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000c652b000-0x00000000c6531fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000c6532000-0x00000000c6976fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000c6977000-0x00000000c6d2dfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000c6d2e000-0x00000000d9871fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d9872000-0x00000000d98fbfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d98fc000-0x00000000d991bfff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000d991c000-0x00000000d9a06fff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000d9a07000-0x00000000d9f7ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d9f80000-0x00000000d9ffefff] type 20
[ 0.000000] BIOS-e820: [mem 0x00000000d9fff000-0x00000000d9ffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dc000000-0x00000000de1fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041fdfffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] efi: EFI v2.31 by American Megatrends
[ 0.000000] efi: ACPI=0xd9902000 ACPI 2.0=0xd9902000 SMBIOS=0xd9f7e498
MPS=0xf4ea0
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Hewlett-Packard HP EliteDesk 800 G1 SFF/1998, BIOS L01
v02.71 05/09/2017
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x41fe00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-DFFFF uncachable
[ 0.000000] E0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7C00000000 write-back
[ 0.000000] 1 base 0400000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 3 base 00DC000000 mask 7FFC000000 uncachable
[ 0.000000] 4 base 041FE00000 mask 7FFFE00000 uncachable
[ 0.000000] 5 disabled
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] e820: update [mem 0xdc000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xda000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000f4e90-0x000f4e9f] mapped at
[ffffffffff240e90]
[ 0.000000] Base memory trampoline at [ffff8afb80097000] 97000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] BRK [0x3b8a06000, 0x3b8a06fff] PGTABLE
[ 0.000000] BRK [0x3b8a07000, 0x3b8a07fff] PGTABLE
[ 0.000000] BRK [0x3b8a08000, 0x3b8a08fff] PGTABLE
[ 0.000000] BRK [0x3b8a09000, 0x3b8a09fff] PGTABLE
[ 0.000000] BRK [0x3b8a0a000, 0x3b8a0afff] PGTABLE
[ 0.000000] BRK [0x3b8a0b000, 0x3b8a0bfff] PGTABLE
[ 0.000000] BRK [0x3b8a0c000, 0x3b8a0cfff] PGTABLE
[ 0.000000] BRK [0x3b8a0d000, 0x3b8a0dfff] PGTABLE
[ 0.000000] BRK [0x3b8a0e000, 0x3b8a0efff] PGTABLE
[ 0.000000] BRK [0x3b8a0f000, 0x3b8a0ffff] PGTABLE
[ 0.000000] BRK [0x3b8a10000, 0x3b8a10fff] PGTABLE
[ 0.000000] Secure boot could not be determined
[ 0.000000] RAMDISK: [mem 0x3537b000-0x369b4fff]
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000D9902000 000024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 0x00000000D9902090 0000A4 (v01 HPQOEM SLIC-BPC
20170509 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000D9910010 00010C (v05 HPQOEM SLIC-BPC
20170509 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000D99021C8 00DE46 (v02 HPQOEM SLIC-BPC
00000001 INTL 20091112)
[ 0.000000] ACPI: FACS 0x00000000D9A05080 000040
[ 0.000000] ACPI: APIC 0x00000000D9910120 000072 (v03 HPQOEM SLIC-BPC
20170509 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000D9910198 000044 (v01 HPQOEM SLIC-BPC
20170509 AMI 00010013)
[ 0.000000] ACPI: SSDT 0x00000000D99101E0 000539 (v01 PmRef Cpu0Ist
00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000D9910720 000AD8 (v01 PmRef CpuPm
00003000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000D99111F8 0001C7 (v01 PmRef LakeTiny
00003000 INTL 20120711)
[ 0.000000] ACPI: MCFG 0x00000000D99113C0 00003C (v01 HPQOEM SLIC-BPC
20170509 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000D9911400 000038 (v01 HPQOEM SLIC-BPC
20170509 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000D9911438 00036D (v01 SataRe SataTabl
00001000 INTL 20120711)
[ 0.000000] ACPI: SSDT 0x00000000D99117A8 00348C (v01 SaSsdt SaSsdt
00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000D9914C38 00668F (v01 COMPAQ WMI
00000001 MSFT 03000001)
[ 0.000000] ACPI: MSDM 0x00000000D991B2C8 000055 (v03 HPQOEM SLIC-BPC
20170509 HPQ 00010013)
[ 0.000000] ACPI: ASF! 0x00000000D991B320 0000A5 (v32 INTEL HCG
00000001 TFSM 000F4240)
[ 0.000000] ACPI: TCPA 0x00000000D991B3C8 000032 (v02 APTIO4 NAPAASF
00000001 MSFT 01000013)
[ 0.000000] ACPI: BGRT 0x00000000D991B400 000038 (v00 HPQOEM SLIC-BPC
20170509 AMI 00010013)
[ 0.000000] ACPI: DMAR 0x00000000D991B438 0000B8 (v01 INTEL HSW
00000001 INTL 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000041fdfffff]
[ 0.000000] NODE_DATA(0) allocated [mem 0x41fdfb000-0x41fdfffff]
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000041fdfffff]
[ 0.000000] Device empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000004efff]
[ 0.000000] node 0: [mem 0x0000000000050000-0x000000000009dfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000c652afff]
[ 0.000000] node 0: [mem 0x00000000c6532000-0x00000000c6976fff]
[ 0.000000] node 0: [mem 0x00000000c6d2e000-0x00000000d9871fff]
[ 0.000000] node 0: [mem 0x00000000d9fff000-0x00000000d9ffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000041fdfffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000041fdfffff]
[ 0.000000] On node 0 totalpages: 4166225
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 41 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13843 pages used for memmap
[ 0.000000] DMA32 zone: 885941 pages, LIFO batch:31
[ 0.000000] Normal zone: 51192 pages used for memmap
[ 0.000000] Normal zone: 3276288 pages, LIFO batch:31
[ 0.000000] Reserving Intel graphics memory at
0x00000000dc200000-0x00000000de1fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 4 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0004f000-0x0004ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc652b000-0xc6531fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xc6977000-0xc6d2dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd9872000-0xd98fbfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd98fc000-0xd991bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd991c000-0xd9a06fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd9a07000-0xd9f7ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd9f80000-0xd9ffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xda000000-0xdbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdc000000-0xde1fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xde200000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xde200000-0xf7ffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:512 nr_cpumask_bits:512 nr_cpu_ids:4
nr_node_ids:1
[ 0.000000] percpu: Embedded 44 pages/cpu @ffff8aff9fa00000 s142232 r8192
d29800 u524288
[ 0.000000] pcpu-alloc: s142232 r8192 d29800 u524288 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4101085
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-4.14.0-3-amd64
root=UUID=78f2fe7c-bc1b-4073-aa07-9ea42b0ab9e0 ro quiet
drm_kms_helper.edid_firmware=VGA-1:edid/1280x1024.bin
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 16049068K/16664900K available (10252K kernel code, 1146K
rwdata, 3040K rodata, 1512K init, 664K bss, 615832K reserved, 0K cma-reserved)
[ 0.000000] Kernel/User page tables isolation: enabled
[ 0.000000] ftrace: allocating 29041 entries in 114 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=512 to nr_cpu_ids=4.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 33024, nr_irqs: 456, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] spurious 8259A interrupt: IRQ7.
[ 0.004000] tsc: Detected 3192.606 MHz processor
[ 0.004000] Calibrating delay loop (skipped), value calculated using timer
frequency.. 6385.21 BogoMIPS (lpj=12770424)
[ 0.004000] pid_max: default: 32768 minimum: 301
[ 0.004000] ACPI: Core revision 20170728
[ 0.013654] ACPI: 7 ACPI AML tables successfully acquired and loaded
[ 0.013991] Security Framework initialized
[ 0.013991] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.014003] AppArmor: AppArmor initialized
[ 0.016038] Dentry cache hash table entries: 2097152 (order: 12, 16777216
bytes)
[ 0.017073] Inode-cache hash table entries: 1048576 (order: 11, 8388608
bytes)
[ 0.017116] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.017148] Mountpoint-cache hash table entries: 32768 (order: 6, 262144
bytes)
[ 0.017305] CPU: Physical Processor ID: 0
[ 0.017306] CPU: Processor Core ID: 0
[ 0.017310] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.017310] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.017314] mce: CPU supports 9 MCE banks
[ 0.017321] CPU0: Thermal monitoring enabled (TM1)
[ 0.017332] process: using mwait in idle threads
[ 0.017334] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[ 0.017335] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.017336] Spectre V2 mitigation: Mitigation: Full generic retpoline
[ 0.017911] Freeing SMP alternatives memory: 28K
[ 0.023414] smpboot: Max logical packages: 1
[ 0.023418] DMAR: Host address width 39
[ 0.023419] DMAR: DRHD base: 0x000000fed90000 flags: 0x0
[ 0.023426] DMAR: dmar0: reg_base_addr fed90000 ver 1:0 cap c0000020660462
ecap f0101a
[ 0.023427] DMAR: DRHD base: 0x000000fed91000 flags: 0x1
[ 0.023430] DMAR: dmar1: reg_base_addr fed91000 ver 1:0 cap d2008020660462
ecap f010da
[ 0.023431] DMAR: RMRR base: 0x000000d9892000 end: 0x000000d989efff
[ 0.023432] DMAR: RMRR base: 0x000000dc000000 end: 0x000000de1fffff
[ 0.023434] DMAR-IR: IOAPIC id 8 under DRHD base 0xfed91000 IOMMU 1
[ 0.023434] DMAR-IR: HPET id 0 under DRHD base 0xfed91000
[ 0.023435] DMAR-IR: Queued invalidation will be enabled to support x2apic
and Intr-remapping.
[ 0.023668] DMAR-IR: Enabled IRQ remapping in x2apic mode
[ 0.023669] x2apic enabled
[ 0.023673] Switched APIC routing to cluster x2apic.
[ 0.024000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.059811] TSC deadline timer enabled
[ 0.059813] smpboot: CPU0: Intel(R) Core(TM) i5-4570 CPU @ 3.20GHz (family:
0x6, model: 0x3c, stepping: 0x3)
[ 0.059864] Performance Events: PEBS fmt2+, Haswell events, 16-deep LBR,
full-width counters, Intel PMU driver.
[ 0.059897] ... version: 3
[ 0.059898] ... bit width: 48
[ 0.059898] ... generic registers: 8
[ 0.059899] ... value mask: 0000ffffffffffff
[ 0.059899] ... max period: 00007fffffffffff
[ 0.059899] ... fixed-purpose events: 3
[ 0.059900] ... event mask: 00000007000000ff
[ 0.059926] Hierarchical SRCU implementation.
[ 0.060000] smp: Bringing up secondary CPUs ...
[ 0.060000] x86: Booting SMP configuration:
[ 0.060000] .... node #0, CPUs: #1
[ 0.060000] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[ 0.060000] #2 #3
[ 0.060661] smp: Brought up 1 node, 4 CPUs
[ 0.060661] smpboot: Total of 4 processors activated (25540.84 BogoMIPS)
[ 0.062473] devtmpfs: initialized
[ 0.062473] x86/mm: Memory block size: 128MB
[ 0.064580] PM: Registering ACPI NVS region [mem 0xc652b000-0xc6531fff]
(28672 bytes)
[ 0.064580] PM: Registering ACPI NVS region [mem 0xd991c000-0xd9a06fff]
(962560 bytes)
[ 0.064580] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff,
max_idle_ns: 7645041785100000 ns
[ 0.064580] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.064580] pinctrl core: initialized pinctrl subsystem
[ 0.064580] NET: Registered protocol family 16
[ 0.064580] cpuidle: using governor ladder
[ 0.064580] cpuidle: using governor menu
[ 0.064580] ACPI FADT declares the system doesn't support PCIe ASPM, so
disable it
[ 0.064580] ACPI: bus type PCI registered
[ 0.064580] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[ 0.064580] PCI: MMCONFIG for domain 0000 [bus 00-3f] at [mem
0xf8000000-0xfbffffff] (base 0xf8000000)
[ 0.064580] PCI: MMCONFIG at [mem 0xf8000000-0xfbffffff] reserved in E820
[ 0.064580] pmd_set_huge: Cannot satisfy [mem 0xf8000000-0xf8200000] with a
huge-page mapping due to MTRR override.
[ 0.064580] PCI: Using configuration type 1 for base access
[ 0.064580] core: PMU erratum BJ122, BV98, HSD29 workaround disabled, HT off
[ 0.064683] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.064683] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.064683] ACPI: Added _OSI(Module Device)
[ 0.064683] ACPI: Added _OSI(Processor Device)
[ 0.064683] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.064683] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.064683] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.070364] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.070911] ACPI: Dynamic OEM Table Load:
[ 0.070911] ACPI: SSDT 0xFFFF8AFF8D349400 0003D3 (v01 PmRef Cpu0Cst
00003001 INTL 20120711)
[ 0.070913] ACPI: Dynamic OEM Table Load:
[ 0.070913] ACPI: SSDT 0xFFFF8AFF8CC81000 0005AA (v01 PmRef ApIst
00003000 INTL 20120711)
[ 0.070913] ACPI: Dynamic OEM Table Load:
[ 0.070913] ACPI: SSDT 0xFFFF8AFF8CCFAC00 000119 (v01 PmRef ApCst
00003000 INTL 20120711)
[ 0.070913] ACPI: Interpreter enabled
[ 0.070913] ACPI: (supports S0 S3 S4 S5)
[ 0.070913] ACPI: Using IOAPIC for interrupt routing
[ 0.070913] PCI: Using host bridge windows from ACPI; if necessary, use
"pci=nocrs" and report a bug
[ 0.070913] ACPI: Enabled 7 GPEs in block 00 to 3F
[ 0.078078] ACPI: Power Resource [FN00] (off)
[ 0.078155] ACPI: Power Resource [FN01] (off)
[ 0.078227] ACPI: Power Resource [FN02] (off)
[ 0.078297] ACPI: Power Resource [FN03] (off)
[ 0.078368] ACPI: Power Resource [FN04] (off)
[ 0.079066] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.079069] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM
Segments MSI]
[ 0.079259] acpi PNP0A08:00: _OSC: platform does not support [PCIeHotplug
PME]
[ 0.079362] acpi PNP0A08:00: _OSC: OS now controls [AER PCIeCapability]
[ 0.079362] acpi PNP0A08:00: FADT indicates ASPM is unsupported, using BIOS
configuration
[ 0.079694] PCI host bridge to bus 0000:00
[ 0.079696] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.079697] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.079698] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff
window]
[ 0.079699] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff
window]
[ 0.079700] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff
window]
[ 0.079701] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff
window]
[ 0.079702] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff
window]
[ 0.079703] pci_bus 0000:00: root bus resource [mem 0xde200000-0xfeafffff
window]
[ 0.079704] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.079711] pci 0000:00:00.0: [8086:0c00] type 00 class 0x060000
[ 0.079788] pci 0000:00:02.0: [8086:0412] type 00 class 0x030000
[ 0.079797] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 0.079801] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit
pref]
[ 0.079804] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.079813] pci 0000:00:02.0: BAR 2: assigned to efifb
[ 0.079867] pci 0000:00:03.0: [8086:0c0c] type 00 class 0x040300
[ 0.079873] pci 0000:00:03.0: reg 0x10: [mem 0xf7c34000-0xf7c37fff 64bit]
[ 0.079957] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[ 0.079975] pci 0000:00:14.0: reg 0x10: [mem 0xf7c20000-0xf7c2ffff 64bit]
[ 0.080028] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.080088] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
[ 0.080107] pci 0000:00:16.0: reg 0x10: [mem 0xf7c40000-0xf7c4000f 64bit]
[ 0.080162] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.080217] pci 0000:00:16.3: [8086:8c3d] type 00 class 0x070002
[ 0.080232] pci 0000:00:16.3: reg 0x10: [io 0xf0e0-0xf0e7]
[ 0.080238] pci 0000:00:16.3: reg 0x14: [mem 0xf7c3e000-0xf7c3efff]
[ 0.080339] pci 0000:00:19.0: [8086:153a] type 00 class 0x020000
[ 0.080354] pci 0000:00:19.0: reg 0x10: [mem 0xf7c00000-0xf7c1ffff]
[ 0.080361] pci 0000:00:19.0: reg 0x14: [mem 0xf7c3d000-0xf7c3dfff]
[ 0.080368] pci 0000:00:19.0: reg 0x18: [io 0xf080-0xf09f]
[ 0.080418] pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
[ 0.080477] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[ 0.080497] pci 0000:00:1a.0: reg 0x10: [mem 0xf7c3c000-0xf7c3c3ff]
[ 0.080570] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.080632] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
[ 0.080649] pci 0000:00:1b.0: reg 0x10: [mem 0xf7c30000-0xf7c33fff 64bit]
[ 0.080701] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.080767] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[ 0.080786] pci 0000:00:1d.0: reg 0x10: [mem 0xf7c3b000-0xf7c3b3ff]
[ 0.080859] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.080920] pci 0000:00:1f.0: [8086:8c4e] type 00 class 0x060100
[ 0.081068] pci 0000:00:1f.2: [8086:8c02] type 00 class 0x010601
[ 0.081083] pci 0000:00:1f.2: reg 0x10: [io 0xf0d0-0xf0d7]
[ 0.081090] pci 0000:00:1f.2: reg 0x14: [io 0xf0c0-0xf0c3]
[ 0.081096] pci 0000:00:1f.2: reg 0x18: [io 0xf0b0-0xf0b7]
[ 0.081103] pci 0000:00:1f.2: reg 0x1c: [io 0xf0a0-0xf0a3]
[ 0.081109] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.081116] pci 0000:00:1f.2: reg 0x24: [mem 0xf7c3a000-0xf7c3a7ff]
[ 0.081146] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.081201] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[ 0.081217] pci 0000:00:1f.3: reg 0x10: [mem 0xf7c39000-0xf7c390ff 64bit]
[ 0.081234] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.082083] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.082135] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 10 11 12 14 15)
*0, disabled.
[ 0.082182] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.082233] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15)
[ 0.082278] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 10 11 12 14 15)
[ 0.082325] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15)
*0, disabled.
[ 0.082375] ACPI: PCI Interrupt Link [LNKG] (IRQs *3 4 5 6 10 11 12 14 15)
[ 0.082426] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15)
[ 0.084006] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.084006] pci 0000:00:02.0: vgaarb: VGA device added:
decodes=io+mem,owns=io+mem,locks=none
[ 0.084007] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.084008] vgaarb: loaded
[ 0.084036] EDAC MC: Ver: 3.0.0
[ 0.084076] Registered efivars operations
[ 0.100202] PCI: Using ACPI for IRQ routing
[ 0.101311] PCI: pci_cache_line_size set to 64 bytes
[ 0.101338] e820: reserve RAM buffer [mem 0x0004f000-0x0004ffff]
[ 0.101339] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[ 0.101339] e820: reserve RAM buffer [mem 0xc652b000-0xc7ffffff]
[ 0.101340] e820: reserve RAM buffer [mem 0xc6977000-0xc7ffffff]
[ 0.101341] e820: reserve RAM buffer [mem 0xd9872000-0xdbffffff]
[ 0.101342] e820: reserve RAM buffer [mem 0xda000000-0xdbffffff]
[ 0.101343] e820: reserve RAM buffer [mem 0x41fe00000-0x41fffffff]
[ 0.101410] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.101410] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.102066] clocksource: Switched to clocksource hpet
[ 0.106729] VFS: Disk quotas dquot_6.6.0
[ 0.106746] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.106821] AppArmor: AppArmor Filesystem Enabled
[ 0.106834] pnp: PnP ACPI init
[ 0.106918] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.106922] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.107012] pnp 00:01: can't evaluate _CRS: 12311
[ 0.107032] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107050] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.107083] system 00:03: [io 0x1854-0x1857] has been reserved
[ 0.107086] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02
(active)
[ 0.107183] system 00:04: [io 0x0a20-0x0a3f] has been reserved
[ 0.107184] system 00:04: [io 0x0a10-0x0a1f] has been reserved
[ 0.107186] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107209] pnp 00:05: Plug and Play ACPI device, IDs PNP0303 PNP030b
(active)
[ 0.107240] pnp 00:06: Plug and Play ACPI device, IDs PNP0f03 PNP0f13
(active)
[ 0.107275] system 00:07: [io 0x04d0-0x04d1] has been reserved
[ 0.107278] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.107420] pnp 00:08: [dma 0 disabled]
[ 0.107492] pnp 00:08: Plug and Play ACPI device, IDs PNP0501 (active)
[ 0.107661] pnp 00:09: Plug and Play ACPI device, IDs IFX0102 PNP0c31
(active)
[ 0.108048] system 00:0a: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.108049] system 00:0a: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.108051] system 00:0a: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.108052] system 00:0a: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.108053] system 00:0a: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.108054] system 00:0a: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.108056] system 00:0a: [mem 0xfed90000-0xfed93fff] could not be reserved
[ 0.108057] system 00:0a: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.108058] system 00:0a: [mem 0xff000000-0xffffffff] has been reserved
[ 0.108059] system 00:0a: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.108061] system 00:0a: [mem 0xf7fdf000-0xf7fdffff] has been reserved
[ 0.108062] system 00:0a: [mem 0xf7fe0000-0xf7feffff] has been reserved
[ 0.108065] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.108316] pnp: PnP ACPI: found 11 devices
[ 0.114445] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff,
max_idle_ns: 2085701024 ns
[ 0.114451] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.114452] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.114453] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.114454] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[ 0.114455] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[ 0.114456] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[ 0.114457] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[ 0.114458] pci_bus 0000:00: resource 11 [mem 0xde200000-0xfeafffff window]
[ 0.114541] NET: Registered protocol family 2
[ 0.114656] TCP established hash table entries: 131072 (order: 8, 1048576
bytes)
[ 0.114784] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.114891] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.114914] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.114949] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.115012] NET: Registered protocol family 1
[ 0.115021] pci 0000:00:02.0: Video device with shadowed ROM at [mem
0x000c0000-0x000dffff]
[ 0.164096] PCI: CLS 64 bytes, default 64
[ 0.164122] Unpacking initramfs...
[ 0.449111] Freeing initrd memory: 22760K
[ 0.449159] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.449161] software IO TLB [mem 0xc252b000-0xc652b000] (64MB) mapped at
[ffff8afc4252b000-ffff8afc4652afff]
[ 0.449458] audit: initializing netlink subsys (disabled)
[ 0.449516] audit: type=2000 audit(1522768167.448:1): state=initialized
audit_enabled=0 res=1
[ 0.449744] workingset: timestamp_bits=40 max_order=22 bucket_order=0
[ 0.449782] zbud: loaded
[ 0.677791] Key type asymmetric registered
[ 0.677792] Asymmetric key parser 'x509' registered
[ 0.677802] Block layer SCSI generic (bsg) driver version 0.4 loaded (major
249)
[ 0.677833] io scheduler noop registered
[ 0.677833] io scheduler deadline registered
[ 0.677843] io scheduler cfq registered (default)
[ 0.677843] io scheduler mq-deadline registered
[ 0.677915] efifb: probing for efifb
[ 0.677924] efifb: framebuffer at 0xe0000000, using 1920k, total 1920k
[ 0.677925] efifb: mode is 800x600x32, linelength=3200, pages=1
[ 0.677926] efifb: scrolling: redraw
[ 0.677927] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[ 0.678664] Console: switching to colour frame buffer device 100x37
[ 0.679321] fb0: EFI VGA frame buffer device
[ 0.679327] intel_idle: MWAIT substates: 0x42120
[ 0.679327] intel_idle: v0.4.1 model 0x3C
[ 0.679462] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.679660] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.700110] 00:08: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a
16550A
[ 0.700385] serial 0000:00:16.3: enabling device (0000 -> 0003)
[ 0.720721] 0000:00:16.3: ttyS1 at I/O 0xf0e0 (irq = 19, base_baud = 115200)
is a 16550A
[ 0.720939] Linux agpgart interface v0.103
[ 0.753011] tpm_tis 00:09: 1.2 TPM (device-id 0xB, rev-id 16)
[ 0.892043] tpm tpm0: A TPM error (7) occurred attempting to read a pcr value
[ 0.892063] tpm tpm0: TPM is disabled/deactivated (0x7)
[ 0.892215] AMD IOMMUv2 driver by Joerg Roedel <jroe...@suse.de>
[ 0.892215] AMD IOMMUv2 functionality not available on this system
[ 0.892535] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at
0x60,0x64 irq 1,12
[ 0.895363] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.895367] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 0.895517] mousedev: PS/2 mouse device common for all mice
[ 0.895560] rtc_cmos 00:02: RTC can wake from S4
[ 0.895681] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.895706] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram,
hpet irqs
[ 0.895714] intel_pstate: Intel P-state driver initializing
[ 0.895988] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.897041] NET: Registered protocol family 10
[ 0.897541] Segment Routing with IPv6
[ 0.897577] mip6: Mobile IPv6
[ 0.897580] NET: Registered protocol family 17
[ 0.897584] mpls_gso: MPLS GSO support
[ 0.898272] microcode: sig=0x306c3, pf=0x2, revision=0x24
[ 0.898503] microcode: Microcode Update Driver: v2.2.
[ 0.898533] sched_clock: Marking stable (898476328, 0)->(904633507, -6157179)
[ 0.899225] registered taskstats version 1
[ 0.899261] zswap: loaded using pool lzo/zbud
[ 0.899491] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.921029] tpm tpm0: A TPM error (7) occurred attempting to read a pcr value
[ 0.921104] ima: No TPM chip found, activating TPM-bypass! (rc=7)
[ 0.921679] rtc_cmos 00:02: setting system clock to 2018-04-03 15:09:28 UTC
(1522768168)
[ 0.925951] Freeing unused kernel memory: 1512K
[ 0.925953] Write protecting the kernel read-only data: 16384k
[ 0.927156] Freeing unused kernel memory: 2012K
[ 0.933816] Freeing unused kernel memory: 1056K
[ 0.938973] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.938973] x86/mm: Checking user space page tables
[ 0.942217] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 0.991155] pps_core: LinuxPPS API ver. 1 registered
[ 0.991156] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo
Giometti <giome...@linux.it>
[ 0.991395] PTP clock support registered
[ 0.994157] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 0.994158] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 0.994307] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to
dynamic conservative mode
[ 0.994926] (NULL device *): hwmon_device_register() is deprecated. Please
convert the driver to use hwmon_device_register_with_info().
[ 0.995013] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.995014] ACPI: Thermal Zone [TZ00] (28 C)
[ 0.995171] thermal LNXTHERM:01: registered as thermal_zone1
[ 0.995171] ACPI: Thermal Zone [TZ01] (30 C)
[ 0.995886] ACPI: bus type USB registered
[ 0.995898] usbcore: registered new interface driver usbfs
[ 0.995904] usbcore: registered new interface driver hub
[ 0.999875] AVX2 version of gcm_enc/dec engaged.
[ 0.999875] AES CTR mode by8 optimization enabled
[ 1.002450] SCSI subsystem initialized
[ 1.005489] usbcore: registered new device driver usb
[ 1.006348] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.006488] ehci-pci: EHCI PCI platform driver
[ 1.012215] libata version 3.00 loaded.
[ 1.088122] e1000e 0000:00:19.0 0000:00:19.0 (uninitialized): registered PHC
clock
[ 1.174931] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1)
a0:d3:c1:27:a5:bf
[ 1.174933] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection
[ 1.174978] e1000e 0000:00:19.0 eth0: MAC: 11, PHY: 12, PBA No: FFFFFF-0FF
[ 1.175197] i801_smbus 0000:00:1f.3: SPD Write Disable is set
[ 1.175225] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 1.175884] e1000e 0000:00:19.0 eno1: renamed from eth0
[ 1.176769] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 1.176775] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus
number 1
[ 1.176792] ehci-pci 0000:00:1a.0: debug port 2
[ 1.180689] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 1.180698] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7c3c000
[ 1.196078] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 1.196157] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.196158] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.196160] usb usb1: Product: EHCI Host Controller
[ 1.196161] usb usb1: Manufacturer: Linux 4.14.0-3-amd64 ehci_hcd
[ 1.196162] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.196373] hub 1-0:1.0: USB hub found
[ 1.196379] hub 1-0:1.0: 3 ports detected
[ 1.196712] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 1.196716] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus
number 2
[ 1.196728] ehci-pci 0000:00:1d.0: debug port 2
[ 1.200620] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 1.200635] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7c3b000
[ 1.216094] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 1.216169] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.216171] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.216172] usb usb2: Product: EHCI Host Controller
[ 1.216174] usb usb2: Manufacturer: Linux 4.14.0-3-amd64 ehci_hcd
[ 1.216175] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.216409] hub 2-0:1.0: USB hub found
[ 1.216416] hub 2-0:1.0: 3 ports detected
[ 1.216798] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.216804] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus
number 3
[ 1.217905] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100
quirks 0x00009810
[ 1.217911] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 1.218054] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.218056] usb usb3: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.218059] usb usb3: Product: xHCI Host Controller
[ 1.218061] usb usb3: Manufacturer: Linux 4.14.0-3-amd64 xhci-hcd
[ 1.218063] usb usb3: SerialNumber: 0000:00:14.0
[ 1.218232] hub 3-0:1.0: USB hub found
[ 1.218258] hub 3-0:1.0: 15 ports detected
[ 1.222996] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 1.223002] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus
number 4
[ 1.223071] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.223073] usb usb4: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 1.223075] usb usb4: Product: xHCI Host Controller
[ 1.223078] usb usb4: Manufacturer: Linux 4.14.0-3-amd64 xhci-hcd
[ 1.223080] usb usb4: SerialNumber: 0000:00:14.0
[ 1.223256] hub 4-0:1.0: USB hub found
[ 1.223278] hub 4-0:1.0: 6 ports detected
[ 1.223943] usb: port power management may be unreliable
[ 1.224396] ahci 0000:00:1f.2: version 3.0
[ 1.224693] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 5 ports 6 Gbps 0x5
impl SATA mode
[ 1.224698] ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part ems
apst
[ 1.240810] scsi host0: ahci
[ 1.240990] scsi host1: ahci
[ 1.241166] scsi host2: ahci
[ 1.241342] scsi host3: ahci
[ 1.241545] scsi host4: ahci
[ 1.241606] ata1: SATA max UDMA/133 abar m2048@0xf7c3a000 port 0xf7c3a100
irq 28
[ 1.241607] ata2: DUMMY
[ 1.241610] ata3: SATA max UDMA/133 abar m2048@0xf7c3a000 port 0xf7c3a200
irq 28
[ 1.241610] ata4: DUMMY
[ 1.241611] ata5: DUMMY
[ 1.468243] tsc: Refined TSC clocksource calibration: 3192.621 MHz
[ 1.468261] clocksource: tsc: mask: 0xffffffffffffffff max_cycles:
0x2e050f5cadc, max_idle_ns: 440795334583 ns
[ 1.532119] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.552117] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.556118] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.556125] usb 3-3: new full-speed USB device number 2 using xhci_hcd
[ 1.556150] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.557576] ata1.00: ATA-8: WDC WD5000AAKX-60U6AA0, 18.01H18, max UDMA/100
[ 1.557582] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.559005] ata1.00: configured for UDMA/100
[ 1.559450] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKX-6 1H18
PQ: 0 ANSI: 5
[ 1.561168] ata3.00: ATAPI: hp CDDVDW SN-208FB, HJ10, max UDMA/100
[ 1.566693] ata3.00: configured for UDMA/100
[ 1.572604] scsi 2:0:0:0: CD-ROM hp CDDVDW SN-208FB HJ10
PQ: 0 ANSI: 5
[ 1.590914] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466
GiB)
[ 1.590922] sd 0:0:0:0: [sda] Write Protect is off
[ 1.590923] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.590935] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled,
doesn't support DPO or FUA
[ 1.611251] sr 2:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw
xa/form2 cdda tray
[ 1.611253] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.611460] sr 2:0:0:0: Attached scsi CD-ROM sr0
[ 1.633884] sda: sda1 sda2 sda3 sda4
[ 1.634633] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.688419] usb 1-1: New USB device found, idVendor=8087, idProduct=8008
[ 1.688421] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.688782] hub 1-1:1.0: USB hub found
[ 1.688861] hub 1-1:1.0: 6 ports detected
[ 1.707975] usb 3-3: New USB device found, idVendor=0b0e, idProduct=0305
[ 1.707977] usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.707978] usb 3-3: Product: Jabra EVOLVE LINK MS
[ 1.707979] usb 3-3: Manufacturer: GN Netcom A/S
[ 1.707979] usb 3-3: SerialNumber: 00039093A1F207
[ 1.708407] usb 2-1: New USB device found, idVendor=8087, idProduct=8000
[ 1.708409] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.708793] hub 2-1:1.0: USB hub found
[ 1.708870] hub 2-1:1.0: 8 ports detected
[ 1.836069] usb 3-4: new high-speed USB device number 3 using xhci_hcd
[ 2.001350] usb 3-4: New USB device found, idVendor=1737, idProduct=0077
[ 2.001352] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.001353] usb 3-4: Product: 802.11 g WLAN
[ 2.001354] usb 3-4: Manufacturer: Ralink
[ 2.001355] usb 3-4: SerialNumber: 1.0
[ 2.128100] usb 3-11: new low-speed USB device number 4 using xhci_hcd
[ 2.279965] usb 3-11: New USB device found, idVendor=046d, idProduct=c077
[ 2.279968] usb 3-11: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 2.279970] usb 3-11: Product: USB Optical Mouse
[ 2.279972] usb 3-11: Manufacturer: Logitech
[ 2.408101] usb 3-12: new low-speed USB device number 5 using xhci_hcd
[ 2.492352] clocksource: Switched to clocksource tsc
[ 2.576664] usb 3-12: New USB device found, idVendor=03f0, idProduct=034a
[ 2.576668] usb 3-12: New USB device strings: Mfr=1, Product=2,
SerialNumber=0
[ 2.576671] usb 3-12: Product: HP Elite USB Keyboard
[ 2.576673] usb 3-12: Manufacturer: Chicony
[ 2.585178] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.153875] usbcore: registered new interface driver usbhid
[ 3.153876] usbhid: USB HID core driver
[ 3.156701] input: GN Netcom A/S Jabra EVOLVE LINK MS as
/devices/pci0000:00/0000:00:14.0/usb3/3-3/3-3:1.3/0003:0B0E:0305.0001/input/input3
[ 3.216534] hid-generic 0003:0B0E:0305.0001: input,hiddev0,hidraw0: USB HID
v1.00 Device [GN Netcom A/S Jabra EVOLVE LINK MS] on usb-0000:00:14.0-3/input3
[ 3.216810] input: Logitech USB Optical Mouse as
/devices/pci0000:00/0000:00:14.0/usb3/3-11/3-11:1.0/0003:046D:C077.0002/input/input4
[ 3.217092] hid-generic 0003:046D:C077.0002: input,hidraw1: USB HID v1.11
Mouse [Logitech USB Optical Mouse] on usb-0000:00:14.0-11/input0
[ 3.217423] input: Chicony HP Elite USB Keyboard as
/devices/pci0000:00/0000:00:14.0/usb3/3-12/3-12:1.0/0003:03F0:034A.0003/input/input5
[ 3.276521] hid-generic 0003:03F0:034A.0003: input,hidraw2: USB HID v1.10
Keyboard [Chicony HP Elite USB Keyboard] on usb-0000:00:14.0-12/input0
[ 3.277029] input: Chicony HP Elite USB Keyboard as
/devices/pci0000:00/0000:00:14.0/usb3/3-12/3-12:1.1/0003:03F0:034A.0004/input/input6
[ 3.336324] hid-generic 0003:03F0:034A.0004: input,hidraw3: USB HID v1.10
Device [Chicony HP Elite USB Keyboard] on usb-0000:00:14.0-12/input1
[ 3.376337] PM: Starting manual resume from disk
[ 3.376497] PM: Image not found (code -22)
[ 3.544398] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts:
(null)
[ 4.797472] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 4.976457] systemd[1]: systemd 238 running in system mode. (+PAM +AUDIT
+SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS
+ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2
default-hierarchy=hybrid)
[ 4.996221] systemd[1]: Detected architecture x86-64.
[ 5.008987] systemd[1]: Set hostname to <moon>.
[ 5.477347] random: crng init done
[ 5.803119] systemd[1]: File /lib/systemd/system/systemd-journald.service:35
configures an IP firewall (IPAddressDeny=any), but the local system does not
support BPF/cgroup based firewalling.
[ 5.803121] systemd[1]: Proceeding WITHOUT firewalling in effect! (This
warning is only shown for the first loaded unit using IP firewalling.)
[ 6.505206] systemd[1]: Started Forward Password Requests to Wall Directory
Watch.
[ 6.505251] systemd[1]: Started Dispatch Password Requests to Console
Directory Watch.
[ 6.505364] systemd[1]: Set up automount Arbitrary Executable File Formats
File System Automount Point.
[ 6.505413] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 6.505456] systemd[1]: Listening on Journal Socket (/dev/log).
[ 7.049007] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 7.062612] lp: driver loaded but no devices found
[ 7.130266] ppdev: user-space parallel port driver
[ 7.249897] systemd-journald[263]: Received request to flush runtime journal
from PID 1
[ 8.407390] input: Power Button as
/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input7
[ 8.407402] ACPI: Power Button [PWRB]
[ 8.407435] input: Power Button as
/devices/LNXSYSTM:00/LNXPWRBN:00/input/input8
[ 8.407440] ACPI: Power Button [PWRF]
[ 8.668175] EFI Variables Facility v0.08 2004-May-17
[ 8.764874] ACPI Warning: SystemIO range
0x0000000000000428-0x000000000000042F conflicts with OpRegion
0x0000000000000400-0x000000000000047F (\PMIO) (20170728/utaddress-247)
[ 8.764879] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 8.764881] ACPI Warning: SystemIO range
0x0000000000000540-0x000000000000054F conflicts with OpRegion
0x0000000000000500-0x00000000000008FF (\GPR) (20170728/utaddress-247)
[ 8.764884] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 8.764884] ACPI Warning: SystemIO range
0x0000000000000530-0x000000000000053F conflicts with OpRegion
0x0000000000000500-0x000000000000053F (\GPRL) (20170728/utaddress-247)
[ 8.764886] ACPI Warning: SystemIO range
0x0000000000000530-0x000000000000053F conflicts with OpRegion
0x0000000000000500-0x00000000000008FF (\GPR) (20170728/utaddress-247)
[ 8.764889] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 8.764889] ACPI Warning: SystemIO range
0x0000000000000500-0x000000000000052F conflicts with OpRegion
0x0000000000000500-0x000000000000053F (\GPRL) (20170728/utaddress-247)
[ 8.764891] ACPI Warning: SystemIO range
0x0000000000000500-0x000000000000052F conflicts with OpRegion
0x0000000000000500-0x00000000000008FF (\GPR) (20170728/utaddress-247)
[ 8.764893] ACPI: If an ACPI driver is available for this device, you should
use it instead of the native driver
[ 8.764893] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 8.887562] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms
ovfl timer
[ 8.887562] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 8.887563] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 8.887563] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 8.887564] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 8.947181] pstore: using zlib compression
[ 8.947198] pstore: Registered efi as persistent store backend
[ 9.062392] input: PC Speaker as /devices/platform/pcspkr/input/input9
[ 9.223694] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 9.223714] sr 2:0:0:0: Attached scsi generic sg1 type 5
[ 9.324944] [drm] Memory usable by graphics device = 2048M
[ 9.324946] checking generic (e0000000 1e0000) vs hw (e0000000 10000000)
[ 9.324947] fb: switching to inteldrmfb from EFI VGA
[ 9.324970] Console: switching to colour dummy device 80x25
[ 9.325082] [drm] Replacing VGA console driver
[ 9.330049] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 9.330050] [drm] Driver supports precise vblank timestamp query.
[ 9.332027] i915 0000:00:02.0: vgaarb: changed VGA decodes:
olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 9.334637] [drm] Initialized i915 1.6.0 20170818 for 0000:00:02.0 on minor 0
[ 9.334762] [Firmware Bug]: Duplicate ACPI video bus devices for the same
VGA controller, please try module parameter "video.allow_duplicates=1"if the
current driver doesn't work.
[ 9.571442] input: HP WMI hotkeys as /devices/virtual/input/input10
[ 9.574053] [drm] Got built-in EDID base block and 0 extensions from
"edid/1280x1024.bin" for connector "VGA-1"
[ 9.802768] fbcon: inteldrmfb (fb0) is primary device
[ 9.841114] snd_hda_intel 0000:00:03.0: enabling device (0100 -> 0102)
[ 9.841239] snd_hda_intel 0000:00:1b.0: enabling device (0100 -> 0102)
[ 9.881875] snd_hda_codec_realtek hdaudioC1D0: autoconfig for ALC221:
line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line
[ 9.881876] snd_hda_codec_realtek hdaudioC1D0: speaker_outs=1
(0x17/0x0/0x0/0x0/0x0)
[ 9.881877] snd_hda_codec_realtek hdaudioC1D0: hp_outs=1
(0x21/0x0/0x0/0x0/0x0)
[ 9.881878] snd_hda_codec_realtek hdaudioC1D0: mono: mono_out=0x0
[ 9.881879] snd_hda_codec_realtek hdaudioC1D0: inputs:
[ 9.881880] snd_hda_codec_realtek hdaudioC1D0: Mic=0x1a
[ 9.881881] snd_hda_codec_realtek hdaudioC1D0: Line=0x1b
[ 9.920719] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops
i915_audio_component_bind_ops [i915])
[ 9.920719] Console: switching to colour frame buffer device 160x64
[ 9.928806] input: HDA Intel PCH Mic as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input11
[ 9.928842] input: HDA Intel PCH Line as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input12
[ 9.928873] input: HDA Intel PCH Line Out as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input13
[ 9.928903] input: HDA Intel PCH Front Headphone as
/devices/pci0000:00/0000:00:1b.0/sound/card1/input14
[ 9.939078] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 9.960091] [drm] Got built-in EDID base block and 0 extensions from
"edid/1280x1024.bin" for connector "VGA-1"
[ 10.002088] iTCO_vendor_support: vendor-support=0
[ 10.010057] input: HDA Intel HDMI HDMI/DP,pcm=3 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input15
[ 10.010091] input: HDA Intel HDMI HDMI/DP,pcm=7 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input16
[ 10.010120] input: HDA Intel HDMI HDMI/DP,pcm=8 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input17
[ 10.010147] input: HDA Intel HDMI HDMI/DP,pcm=9 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input18
[ 10.010175] input: HDA Intel HDMI HDMI/DP,pcm=10 as
/devices/pci0000:00/0000:00:03.0/sound/card0/input19
[ 10.060477] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 10.060512] iTCO_wdt: Found a Lynx Point TCO device (Version=2,
TCOBASE=0x0460)
[ 10.060587] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 10.831337] usb 3-3: 1:1: cannot get freq at ep 0x83
[ 10.832899] usb 3-3: 2:1: cannot get freq at ep 0x4
[ 10.840130] intel_rapl: Found RAPL domain package
[ 10.840131] intel_rapl: Found RAPL domain core
[ 10.840131] intel_rapl: Found RAPL domain uncore
[ 10.840132] intel_rapl: Found RAPL domain dram
[ 10.840134] intel_rapl: RAPL package 0 domain package locked by BIOS
[ 10.840137] intel_rapl: RAPL package 0 domain dram locked by BIOS
[ 10.847507] usbcore: registered new interface driver snd-usb-audio
[ 10.952195] Adding 16686076k swap on /dev/sda3. Priority:-2 extents:1
across:16686076k FS
[ 11.296298] usb 3-4: reset high-speed USB device number 3 using xhci_hcd
[ 11.458784] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3070, rev 0201
detected
[ 11.469920] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 0006 detected
[ 11.570251] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 11.570436] usbcore: registered new interface driver rt2800usb
[ 11.714339] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts:
(null)
[ 13.136607] audit: type=1400 audit(1522768180.710:2): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-senddoc"
pid=575 comm="apparmor_parser"
[ 13.170577] audit: type=1400 audit(1522768180.742:3): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/bin/man" pid=572
comm="apparmor_parser"
[ 13.170579] audit: type=1400 audit(1522768180.742:4): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_filter" pid=572
comm="apparmor_parser"
[ 13.170581] audit: type=1400 audit(1522768180.742:5): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="man_groff" pid=572
comm="apparmor_parser"
[ 13.285130] audit: type=1400 audit(1522768180.858:6): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-xpdfimport"
pid=577 comm="apparmor_parser"
[ 13.325636] audit: type=1400 audit(1522768180.898:7): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-oopslash"
pid=574 comm="apparmor_parser"
[ 13.699611] audit: type=1400 audit(1522768181.270:8): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-soffice"
pid=576 comm="apparmor_parser"
[ 13.699614] audit: type=1400 audit(1522768181.270:9): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="libreoffice-soffice//gpg"
pid=576 comm="apparmor_parser"
[ 13.716808] audit: type=1400 audit(1522768181.290:10): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="/usr/sbin/cups-browsed"
pid=579 comm="apparmor_parser"
[ 13.735830] audit: type=1400 audit(1522768181.306:11): apparmor="STATUS"
operation="profile_load" profile="unconfined"
name="/usr/lib/telepathy/mission-control-5" pid=578 comm="apparmor_parser"
[ 14.035309] rt2800usb 3-4:1.0 wlx00259ca32202: renamed from wlan0
[ 17.888621] vboxdrv: loading out-of-tree module taints kernel.
[ 17.896328] vboxdrv: Found 4 processor cores
[ 17.920372] vboxdrv: TSC mode is Invariant, tentative frequency 3192621420 Hz
[ 17.920373] vboxdrv: Successfully loaded version 5.1.34 (interface
0x002a0000)
[ 18.330584] VBoxNetFlt: Successfully started.
[ 18.658982] VBoxNetAdp: Successfully started.
[ 18.910445] VBoxPciLinuxInit
[ 19.160745] vboxpci: IOMMU not found (not registered)
[ 19.487459] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading
firmware file 'rt2870.bin'
[ 19.501768] rt2800usb 3-4:1.0: firmware: direct-loading firmware rt2870.bin
[ 19.501771] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware
detected - version: 0.36
[ 19.910989] IPv6: ADDRCONF(NETDEV_UP): wlx00259ca32202: link is not ready
[ 19.950449] IPv6: ADDRCONF(NETDEV_CHANGE): wlx00259ca32202: link becomes
ready
[ 21.603222] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 21.816258] IPv6: ADDRCONF(NETDEV_UP): eno1: link is not ready
[ 25.358318] e1000e: eno1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control:
None
[ 25.358367] IPv6: ADDRCONF(NETDEV_CHANGE): eno1: link becomes ready
[ 30.848237] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 33.651053] kauditd_printk_skb: 13 callbacks suppressed
[ 33.651054] audit: type=1400 audit(1522768201.222:25): apparmor="STATUS"
operation="profile_load" profile="unconfined" name="docker-default" pid=1320
comm="apparmor_parser"
[ 36.972353] bridge: filtering via arp/ip/ip6tables is no longer available by
default. Update your scripts to load br_netfilter if you need this.
[ 36.974262] Bridge firewalling registered
[ 37.738198] Initializing XFRM netlink socket
[ 37.802128] Netfilter messages via NETLINK v0.30.
[ 37.815096] ctnetlink v0.93: registering with nfnetlink.
[ 38.022309] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
[ 38.863375] [drm] Got built-in EDID base block and 0 extensions from
"edid/1280x1024.bin" for connector "VGA-1"
[ 43.237564] usb 3-3: 1:1: cannot get freq at ep 0x83
[ 55.308859] Could not find key with description: [a047d98f708ca78a]
[ 55.308862] process_request_key_err: No key
[ 55.308863] Could not find valid key in user session keyring for sig
specified in mount option: [a047d98f708ca78a]
[ 55.308865] One or more global auth toks could not properly register; rc =
[-2]
[ 55.308866] Error parsing options; rc = [-2]
[ 57.211487] fuse init (API version 7.26)
[ 57.230068] [drm] Got built-in EDID base block and 0 extensions from
"edid/1280x1024.bin" for connector "VGA-1"
[ 62.164122] rfkill: input handler disabled
