Package: src:linux Version: 4.9.135-1 Severity: important Hi kernel team,
I've reproduced this kernel BUG a few times already, with simple operations on various USB devices like brand new Kingston DataTraveler 3.0 (8, 16 or 32GB): [ 1992.998316] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c [ 1992.998372] IP: [<ffffffffc038f32f>] xhci_hub_control+0x19cf/0x1c10 [xhci_hcd] Steps to reproduce: - plug a USB device either on an port of the laptop's base, or on the USB3 port on the laptop; - zero out the /dev/sd? that pops up when the USB device is inserted, to make sure any preexisting partitioning is no factor (did that on the full device first time, then decided to only wipe out the beginning of the block device); - partprobe to make extra sure; - create a partition table with fdisk (not sure I did anything specific here, can double check, probably went for the default); - create a single partition with all free space; - assign type 'b' (W95 FAT32) to it; - use mkfs.vfat -F 32 on the new block device. At this point, said block device appears in Xfce's file manager, Thunar. With or without having copied a few files to it, clicking the “eject” button is sufficient to trigger this BUG. When that happens, input devices work for a few seconds but it isn't possible to get much done; an already-running dmesg -w wouldn't show any traces. Only an UEFI glitch at reboot time would make half a screen appear with a fuzzied trace… Here's a capture obtained through netconsole, enabled a bit before triggering the crash: [ 1745.198739] console [netcon_ext0] disabled [ 1745.198753] console [netcon0] disabled [ 1748.295633] netpoll: netconsole: local port 6665 [ 1748.295637] netpoll: netconsole: local IPv4 address 0.0.0.0 [ 1748.295639] netpoll: netconsole: interface 'eth0' [ 1748.295640] netpoll: netconsole: remote port 6666 [ 1748.295642] netpoll: netconsole: remote IPv4 address 192.168.0.1 [ 1748.295644] netpoll: netconsole: remote ethernet address d8:cb:8a:98:29:59 [ 1748.295647] netpoll: netconsole: local IP 192.168.0.21 [ 1748.295702] console [netcon0] enabled [ 1748.295704] netconsole: network logging started [ 1799.971353] usb 2-2: new SuperSpeed USB device number 4 using xhci_hcd [ 1800.002355] usb 2-2: New USB device found, idVendor=0951, idProduct=1666 [ 1800.002373] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1800.002380] usb 2-2: Product: DataTraveler 3.0 [ 1800.002386] usb 2-2: Manufacturer: Kingston [ 1800.002392] usb 2-2: SerialNumber: 60A44C413BF2F270B62830FF [ 1800.017208] usb-storage 2-2:1.0: USB Mass Storage device detected [ 1800.017367] scsi host3: usb-storage 2-2:1.0 [ 1801.020259] scsi 3:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6 [ 1801.021997] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 1801.022211] sd 3:0:0:0: [sdb] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB) [ 1801.022788] sd 3:0:0:0: [sdb] Write Protect is off [ 1801.022819] sd 3:0:0:0: [sdb] Mode Sense: 4f 00 00 00 [ 1801.023312] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1801.026302] sdb: sdb1 [ 1801.027383] sd 3:0:0:0: [sdb] Attached SCSI removable disk [ 1884.111187] device eth0 left promiscuous mode [ 1901.864615] sdb: sdb1 [ 1939.154007] usb 2-2: USB disconnect, device number 4 [ 1941.618308] usb 2-2: new SuperSpeed USB device number 5 using xhci_hcd [ 1941.649852] usb 2-2: New USB device found, idVendor=0951, idProduct=1666 [ 1941.649863] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [ 1941.649866] usb 2-2: Product: DataTraveler 3.0 [ 1941.649869] usb 2-2: Manufacturer: Kingston [ 1941.649872] usb 2-2: SerialNumber: 60A44C413BF2F270B62830FF [ 1941.659124] usb-storage 2-2:1.0: USB Mass Storage device detected [ 1941.659303] scsi host3: usb-storage 2-2:1.0 [ 1942.682536] scsi 3:0:0:0: Direct-Access Kingston DataTraveler 3.0 PQ: 0 ANSI: 6 [ 1942.683352] sd 3:0:0:0: [sdb] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB) [ 1942.683356] sd 3:0:0:0: Attached scsi generic sg1 type 0 [ 1942.683517] sd 3:0:0:0: [sdb] Write Protect is off [ 1942.683525] sd 3:0:0:0: [sdb] Mode Sense: 4f 00 00 00 [ 1942.683714] sd 3:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 1942.687527] sdb: sdb1 [ 1942.688360] sd 3:0:0:0: [sdb] Attached SCSI removable disk [ 1978.720932] sdb: sdb1 [ 1984.327018] sdb: sdb1 [ 1984.414750] sdb: sdb1 [ 1984.587241] sdb: sdb1 [ 1992.998123] usb 2-2: USB disconnect, device number 5 [ 1992.998316] BUG: unable to handle kernel NULL pointer dereference at 000000000000001c [ 1992.998372] IP: [<ffffffffc038f32f>] xhci_hub_control+0x19cf/0x1c10 [xhci_hcd] [ 1992.998418] PGD 0 [ 1992.998433] [ 1992.998450] Oops: 0000 [#1] SMP [ 1992.998475] Modules linked in: netconsole nfnetlink_queue nfnetlink_log nfnetlink rtl8192cu rtl_usb rtl8192c_common rtlwifi configfs rfcomm ip6t_REJECT nf_reject_ipv6 xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter cmac bnep binfmt_misc usblp arc4 snd_hda_codec_hdmi snd_hda_codec_conexant i2c_designware_platform i2c_designware_core snd_hda_codec_generic snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_hda_ext_core snd_soc_sst_match snd_soc_core snd_compress snd_hda_intel iwlmvm hp_wmi sparse_keymap snd_hda_codec mac80211 intel_rapl x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel kvm snd_hda_core snd_hwdep irqbypass intel_cstate i915 snd_pcm intel_uncore snd_timer iwlwifi intel_rapl_perf snd soundcore cfg80211 idma64 serio_raw uvcvideo videobuf2_vmalloc iTCO_wdt videobuf2_memops iTCO_vendor_support videobuf2_v4l2 drm_kms_helper videobuf2_core btusb videodev qmi_wwan drm btrtl cdc_wdm btbcm evdev usbnet intel_lpss_pci media joydev mii intel_lpss i2c_algo_bit btintel sg shpchp mfd_core intel_pch_thermal mei_me bluetooth mei rfkill wmi battery ac video button hp_wireless acpi_pad tpm_infineon nfsd auth_rpcgss oid_registry nfs_acl lockd grace sunrpc parport_pc ppdev lp parport ip_tables x_tables autofs4 ext4 crc16 jbd2 fscrypto ecb mbcache btrfs algif_skcipher af_alg hid_generic usbhid uas usb_storage dm_crypt dm_mod raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c crc32c_generic raid1 raid0 multipath linear md_mod sd_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd psmouse ahci libahci e1000e i2c_i801 ptp pps_core xhci_pci i2c_smbus libata xhci_hcd scsi_mod usbcore usb_common thermal i2c_hid hid [last unloaded: netconsole] [ 1992.999820] CPU: 1 PID: 6046 Comm: kworker/1:2 Not tainted 4.9.0-8-amd64 #1 Debian 4.9.135-1 [ 1992.999857] Hardware name: HP HP EliteBook Folio 1040 G3/80FA, BIOS N83 Ver. 01.00 12/15/2015 [ 1992.999902] Workqueue: usb_hub_wq hub_event [usbcore] [ 1992.999928] task: ffff9cac0a54b000 task.stack: ffffc02901df8000 [ 1992.999959] RIP: 0010:[<ffffffffc038f32f>] [<ffffffffc038f32f>] xhci_hub_control+0x19cf/0x1c10 [xhci_hcd] [ 1993.000012] RSP: 0018:ffffc02901dfba90 EFLAGS: 00010086 [ 1993.000038] RAX: ffff9cabd8f18000 RBX: ffff9cac969b8000 RCX: 0000000000000000 [ 1993.000070] RDX: 0000000000000060 RSI: 0000000000001201 RDI: ffff9cac968b4284 [ 1993.000213] RBP: 00000000ffffffed R08: 0000000000000008 R09: 0000000000000001 [ 1993.000251] R10: 0000000000000001 R11: 0000000000000212 R12: 000000000000000e [ 1993.000283] R13: ffff9cac968b4000 R14: ffff9cac968b4284 R15: 0000000000000002 [ 1993.000318] FS: 0000000000000000(0000) GS:ffff9cacaf480000(0000) knlGS:0000000000000000 [ 1993.000353] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1993.000371] CR2: 000000000000001c CR3: 0000000314c36000 CR4: 0000000000360670 [ 1993.000393] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1993.000415] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 1993.000437] Stack: [ 1993.000445] ffffffffb8aa4900 072e361b00000005 0000000000000006 ffff9cac00000000 [ 1993.000475] 0000000000000005 ffff9cac968b4238 0000000000000000 ffffffffb8be0302 [ 1993.000502] ffff9cac9e800cc0 0000000001dfbba0 ffff9cac95d07240 ffff9cac9bafe700 [ 1993.000529] Call Trace: [ 1993.000541] [<ffffffffb8aa4900>] ? check_preempt_curr+0x20/0x90 [ 1993.000562] [<ffffffffb8be0302>] ? new_page+0x12/0xa0 [ 1993.000580] [<ffffffffb8c54266>] ? ep_poll_callback+0x106/0x230 [ 1993.000606] [<ffffffffc02e686a>] ? usb_hcd_submit_urb+0x2aa/0xaf0 [usbcore] [ 1993.000629] [<ffffffffb8ef9d3e>] ? __kmalloc_reserve.isra.35+0x2e/0x80 [ 1993.000652] [<ffffffffb8ae7714>] ? lock_timer_base+0x74/0x90 [ 1993.000672] [<ffffffffb8ae759a>] ? __internal_add_timer+0x1a/0x50 [ 1993.000692] [<ffffffffb8ae9f20>] ? add_timer+0x110/0x270 [ 1993.000715] [<ffffffffc02e8aed>] ? usb_start_wait_urb+0x6d/0x170 [usbcore] [ 1993.000741] [<ffffffffc02ed562>] ? usb_release_interface_cache+0x32/0x50 [usbcore] [ 1993.000768] [<ffffffffc02e8ccd>] ? usb_control_msg+0xdd/0x140 [usbcore] [ 1993.000791] [<ffffffffb8e7e3c0>] ? device_release+0x30/0x90 [ 1993.000813] [<ffffffffc02dbc54>] ? set_port_feature+0x44/0x50 [usbcore] [ 1993.000837] [<ffffffffc02dd579>] ? hub_port_disable+0xc9/0x140 [usbcore] [ 1993.000863] [<ffffffffc02e24eb>] ? hub_event+0xd8b/0x15c0 [usbcore] [ 1993.000884] [<ffffffffb90190a4>] ? __switch_to_asm+0x34/0x70 [ 1993.000904] [<ffffffffb90190b0>] ? __switch_to_asm+0x40/0x70 [ 1993.000923] [<ffffffffb8a9421a>] ? process_one_work+0x18a/0x420 [ 1993.000943] [<ffffffffb8a944fd>] ? worker_thread+0x4d/0x490 [ 1993.000962] [<ffffffffb8a944b0>] ? process_one_work+0x420/0x420 [ 1993.000982] [<ffffffffb8a9a569>] ? kthread+0xd9/0xf0 [ 1993.001000] [<ffffffffb90190a4>] ? __switch_to_asm+0x34/0x70 [ 1993.001019] [<ffffffffb8a9a490>] ? kthread_park+0x60/0x60 [ 1993.001038] [<ffffffffb9019137>] ? ret_from_fork+0x57/0x70 [ 1993.001056] Code: e9 2c e7 ff ff 45 31 e4 eb 11 49 83 c4 01 49 81 fc 00 01 00 00 0f 84 f5 f2 ff ff 4b 8b 84 e5 08 04 00 00 48 85 c0 74 e2 48 8b 08 <83> 79 1c 04 40 0f 96 c6 83 bb a0 00 00 00 3f 0f 9f c1 40 38 ce [ 1993.001230] RIP [<ffffffffc038f32f>] xhci_hub_control+0x19cf/0x1c10 [xhci_hcd] [ 1993.001270] RSP <ffffc02901dfba90> [ 1993.001288] CR2: 000000000000001c [ 1993.013222] ---[ end trace 9533e904b0227a58 ]--- [ 2014.005703] INFO: rcu_sched detected stalls on CPUs/tasks: [ 2014.005714] 1-...: (1 GPs behind) idle=001/140000000000001/0 softirq=67859/67860 fqs=2620 [ 2014.005716] (detected by 2, t=5252 jiffies, g=54690, c=54689, q=1460) [ 2014.005719] Task dump for CPU 1: [ 2014.005721] kworker/1:2 R running task 0 6046 2 0x00000008 [ 2014.005731] Workqueue: 0x2de900087b88e8ff (ÿÿHû) [ 2014.005735] ffff9cac9e800cc0 0000000001dfbba0 ffff9cac95d07240 ffff9cac9bafe700 [ 2014.005741] 0000000000000000 ffff9cac00000000 0000000000000000 ffff9cac9750ef00 [ 2014.005746] ffffffffb8c54266 072e361ba39ee992 ffff9cac9b786cc0 00000000fffffff4 [ 2014.005751] Call Trace: [ 2014.005756] [<ffffffffb8c54266>] ? ep_poll_callback+0x106/0x230 [ 2014.005765] [<ffffffffc02e686a>] ? usb_hcd_submit_urb+0x2aa/0xaf0 [usbcore] [ 2014.005769] [<ffffffffb8ef9d3e>] ? __kmalloc_reserve.isra.35+0x2e/0x80 [ 2014.005772] [<ffffffffb8ae7714>] ? lock_timer_base+0x74/0x90 [ 2014.005775] [<ffffffffb8ae759a>] ? __internal_add_timer+0x1a/0x50 [ 2014.005778] [<ffffffffb8ae9f20>] ? add_timer+0x110/0x270 [ 2014.005801] [<ffffffffc02e8aed>] ? usb_start_wait_urb+0x6d/0x170 [usbcore] [ 2014.005808] [<ffffffffc02ed562>] ? usb_release_interface_cache+0x32/0x50 [usbcore] [ 2014.005814] [<ffffffffc02e8ccd>] ? usb_control_msg+0xdd/0x140 [usbcore] [ 2014.005817] [<ffffffffb8e7e3c0>] ? device_release+0x30/0x90 [ 2014.005822] [<ffffffffc02dbc54>] ? set_port_feature+0x44/0x50 [usbcore] [ 2014.005826] [<ffffffffc02dd579>] ? hub_port_disable+0xc9/0x140 [usbcore] [ 2014.005831] [<ffffffffc02e24eb>] ? hub_event+0xd8b/0x15c0 [usbcore] [ 2014.005834] [<ffffffffb90190a4>] ? __switch_to_asm+0x34/0x70 [ 2014.005837] [<ffffffffb90190b0>] ? __switch_to_asm+0x40/0x70 [ 2014.005839] [<ffffffffb8b06cf9>] ? acct_collect+0x169/0x1a0 [ 2014.005842] [<ffffffffb8a7f18a>] ? do_exit+0x74a/0xaf0 [ 2014.005845] [<ffffffffb901a817>] ? rewind_stack_do_exit+0x17/0x20 This resembles #916455 a lot but its trace isn't really readable so I thought a fresh bug report would make sense. If that helps, I can probably test older kernels and/or different devices but I bought a bunch of (two different kinds of) Kingston devices recently, so I don't have much hardware diversity here. At the moment I can't tell it's a regression from older versions as I wasn't using USB devices until a few days ago (testing Tails on bare metal). Also, I can try and get the Xfce file manager out of the way as far as steps to reproduce go; but it's a bit cumbersome to repeat the crash as that happens on my main laptop, that's why I haven't done that yet. -- Package-specific info: ** Version: Linux version 4.9.0-8-amd64 (debian-ker...@lists.debian.org) (gcc version 6.3.0 20170516 (Debian 6.3.0-18+deb9u1) ) #1 SMP Debian 4.9.135-1 (2018-11-11) ** Command line: BOOT_IMAGE=/vmlinuz-4.9.0-8-amd64 root=/dev/mapper/armor--vg-root ro quiet net.ifnames=0 apparmor=1 security=apparmor ** Not tainted ** Kernel log: [ 10.700092] Bluetooth: hci0: Applying Intel DDC parameters completed [ 10.779320] [drm] RC6 on [ 10.890828] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 10.890830] Bluetooth: BNEP filters: protocol multicast [ 10.890834] Bluetooth: BNEP socket layer initialized [ 11.159820] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory [ 11.160366] NFSD: starting 90-second grace period (net ffffffff934dbe80) [ 11.477970] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.719221] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 11.730965] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.733202] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.733588] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.869056] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.869446] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.952648] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 11.960907] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 11.961295] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 12.096700] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 12.097086] iwlwifi 0000:01:00.0: L1 Enabled - LTR Enabled [ 12.180128] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 12.354152] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 12.403960] Ebtables v2.0 registered [ 12.508110] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 12.995902] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 13.000128] tun: Universal TUN/TAP device driver, 1.6 [ 13.000130] tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com> [ 13.063116] virbr46: port 1(virbr46-nic) entered blocking state [ 13.063118] virbr46: port 1(virbr46-nic) entered disabled state [ 13.063182] device virbr46-nic entered promiscuous mode [ 13.219681] nf_conntrack version 0.5.0 (65536 buckets, 262144 max) [ 13.253444] virbr46: port 1(virbr46-nic) entered blocking state [ 13.253446] virbr46: port 1(virbr46-nic) entered listening state [ 13.253488] IPv6: ADDRCONF(NETDEV_UP): virbr46: link is not ready [ 15.259047] virbr46: port 1(virbr46-nic) entered learning state [ 17.275104] virbr46: port 1(virbr46-nic) entered forwarding state [ 17.275108] virbr46: topology change detected, propagating [ 17.275190] IPv6: ADDRCONF(NETDEV_CHANGE): virbr46: link becomes ready [ 18.337131] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready [ 18.380523] wlan0: authenticate with 14:0c:76:c9:bf:04 [ 18.388813] wlan0: send auth to 14:0c:76:c9:bf:04 (try 1/3) [ 18.394332] wlan0: authenticated [ 18.394482] iwlwifi 0000:01:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use [ 18.395055] wlan0: associate with 14:0c:76:c9:bf:04 (try 1/3) [ 18.396364] wlan0: RX AssocResp from 14:0c:76:c9:bf:04 (capab=0x111 status=0 aid=2) [ 18.397771] wlan0: associated [ 18.398320] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 18.472067] wlan0: Limiting TX power to 24 (27 - 3) dBm as advertised by 14:0c:76:c9:bf:04 [ 19.232404] virbr46: port 1(virbr46-nic) entered disabled state [ 19.339544] virbr4: port 1(virbr4-nic) entered blocking state [ 19.339551] virbr4: port 1(virbr4-nic) entered disabled state [ 19.339883] device virbr4-nic entered promiscuous mode [ 19.491900] virbr4: port 1(virbr4-nic) entered blocking state [ 19.491902] virbr4: port 1(virbr4-nic) entered listening state [ 19.545798] virbr4: port 1(virbr4-nic) entered disabled state [ 19.627370] virbr0: port 1(virbr0-nic) entered blocking state [ 19.627373] virbr0: port 1(virbr0-nic) entered disabled state [ 19.627539] device virbr0-nic entered promiscuous mode [ 19.821778] virbr0: port 1(virbr0-nic) entered blocking state [ 19.821780] virbr0: port 1(virbr0-nic) entered listening state [ 19.841921] virbr0: port 1(virbr0-nic) entered disabled state [ 20.897530] Bluetooth: RFCOMM TTY layer initialized [ 20.897535] Bluetooth: RFCOMM socket layer initialized [ 20.897540] Bluetooth: RFCOMM ver 1.11 [11478.460801] perf: interrupt took too long (2541 > 2500), lowering kernel.perf_event_max_sample_rate to 78500 [13673.066124] perf: interrupt took too long (3214 > 3176), lowering kernel.perf_event_max_sample_rate to 62000 ** Model information sys_vendor: HP product_name: HP EliteBook Folio 1040 G3 product_version: chassis_vendor: HP chassis_version: bios_vendor: HP bios_version: N83 Ver. 01.00 board_vendor: HP board_name: 80FA board_version: KBC Version 01.2E ** Loaded modules: rfcomm xt_CHECKSUM iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_tcpudp tun bridge stp llc ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter cmac bnep binfmt_misc hid_generic arc4 snd_hda_codec_hdmi snd_hda_codec_conexant snd_hda_codec_generic i2c_designware_platform i2c_designware_core iwlmvm mac80211 intel_rapl hp_wmi sparse_keymap x86_pkg_temp_thermal intel_powerclamp coretemp kvm_intel snd_soc_skl kvm snd_soc_skl_ipc snd_soc_sst_ipc irqbypass snd_soc_sst_dsp snd_hda_ext_core snd_soc_sst_match intel_cstate snd_soc_core snd_compress intel_uncore intel_rapl_perf i915 snd_hda_intel uvcvideo videobuf2_vmalloc snd_hda_codec iwlwifi videobuf2_memops btusb btrtl btbcm snd_hda_core idma64 btintel snd_hwdep cfg80211 videobuf2_v4l2 bluetooth evdev videobuf2_core joydev snd_pcm serio_raw drm_kms_helper snd_timer snd videodev iTCO_wdt soundcore qmi_wwan drm iTCO_vendor_support cdc_wdm media usbnet intel_lpss_pci mii rfkill mei_me intel_lpss sg i2c_algo_bit mei shpchp mfd_core intel_pch_thermal wmi battery video hp_wireless button acpi_pad tpm_infineon ac nfsd auth_rpcgss oid_registry nfs_acl lockd grace sunrpc parport_pc ppdev lp parport ip_tables x_tables autofs4 ext4 crc16 jbd2 fscrypto ecb mbcache btrfs algif_skcipher af_alg dm_crypt dm_mod raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c crc32c_generic raid1 raid0 multipath linear md_mod sd_mod crct10dif_pclmul crc32_pclmul crc32c_intel ghash_clmulni_intel aesni_intel aes_x86_64 lrw gf128mul glue_helper ablk_helper cryptd psmouse ahci e1000e libahci ptp pps_core i2c_i801 i2c_smbus xhci_pci libata xhci_hcd scsi_mod usbcore usb_common thermal i2c_hid hid ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation Skylake Host Bridge/DRAM Registers [8086:1904] (rev 08) Subsystem: Hewlett-Packard Company Skylake Host Bridge/DRAM Registers [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: skl_uncore 00:02.0 VGA compatible controller [0300]: Intel Corporation HD Graphics 520 [8086:1916] (rev 07) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company HD Graphics 520 [103c:80fa] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 280 Region 0: Memory at e0000000 (64-bit, non-prefetchable) [size=16M] Region 2: Memory at d0000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 3000 [size=64] [virtual] Expansion ROM at 000c0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:14.0 USB controller [0c03]: Intel Corporation Sunrise Point-LP USB 3.0 xHCI Controller [8086:9d2f] (rev 21) (prog-if 30 [XHCI]) Subsystem: Hewlett-Packard Company Sunrise Point-LP USB 3.0 xHCI Controller [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 275 Region 0: Memory at e1120000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd Kernel modules: xhci_pci 00:14.2 Signal processing controller [1180]: Intel Corporation Sunrise Point-LP Thermal subsystem [8086:9d31] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP Thermal subsystem [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 18 Region 0: Memory at e114b000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel_pch_thermal Kernel modules: intel_pch_thermal 00:15.0 Signal processing controller [1180]: Intel Corporation Sunrise Point-LP Serial IO I2C Controller #0 [8086:9d60] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP Serial IO I2C Controller [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 16 Region 0: Memory at e114c000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel-lpss Kernel modules: intel_lpss_pci 00:15.1 Signal processing controller [1180]: Intel Corporation Sunrise Point-LP Serial IO I2C Controller #1 [8086:9d61] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP Serial IO I2C Controller [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 17 Region 0: Memory at e114d000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel-lpss Kernel modules: intel_lpss_pci 00:16.0 Communication controller [0780]: Intel Corporation Sunrise Point-LP CSME HECI #1 [8086:9d3a] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP CSME HECI [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 278 Region 0: Memory at e114e000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: mei_me Kernel modules: mei_me 00:16.3 Serial controller [0700]: Intel Corporation Device [8086:9d3d] (rev 21) (prog-if 02 [16550]) Subsystem: Hewlett-Packard Company Device [103c:80fa] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 19 Region 0: I/O ports at 3080 [size=8] Region 1: Memory at e114a000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: serial 00:17.0 SATA controller [0106]: Intel Corporation Sunrise Point-LP SATA Controller [AHCI mode] [8086:9d03] (rev 21) (prog-if 01 [AHCI 1.0]) Subsystem: Hewlett-Packard Company Sunrise Point-LP SATA Controller [AHCI mode] [103c:80fa] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 276 Region 0: Memory at e1148000 (32-bit, non-prefetchable) [size=8K] Region 1: Memory at e1151000 (32-bit, non-prefetchable) [size=256] Region 2: I/O ports at 3088 [size=8] Region 3: I/O ports at 3090 [size=4] Region 4: I/O ports at 3040 [size=32] Region 5: Memory at e114f000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 00:1c.0 PCI bridge [0604]: Intel Corporation Device [8086:9d13] (rev f1) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 274 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 Memory behind bridge: e1000000-e10fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport Kernel modules: shpchp 00:1f.0 ISA bridge [0601]: Intel Corporation Sunrise Point-LP LPC Controller [8086:9d48] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP LPC Controller [103c:80fa] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.2 Memory controller [0580]: Intel Corporation Sunrise Point-LP PMC [8086:9d21] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP PMC [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at e1140000 (32-bit, non-prefetchable) [size=16K] 00:1f.3 Audio device [0403]: Intel Corporation Sunrise Point-LP HD Audio [8086:9d70] (rev 21) (prog-if 80) Subsystem: Hewlett-Packard Company Sunrise Point-LP HD Audio [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 Interrupt: pin A routed to IRQ 281 Region 0: Memory at e1144000 (64-bit, non-prefetchable) [size=16K] Region 4: Memory at e1130000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel, snd_soc_skl 00:1f.4 SMBus [0c05]: Intel Corporation Sunrise Point-LP SMBus [8086:9d23] (rev 21) Subsystem: Hewlett-Packard Company Sunrise Point-LP SMBus [103c:80fa] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: Memory at e1150000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at efa0 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c_i801 00:1f.6 Ethernet controller [0200]: Intel Corporation Ethernet Connection I219-LM [8086:156f] (rev 21) Subsystem: Hewlett-Packard Company Ethernet Connection I219-LM [103c:80fa] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 277 Region 0: Memory at e1100000 (32-bit, non-prefetchable) [size=128K] Capabilities: <access denied> Kernel driver in use: e1000e Kernel modules: e1000e 01:00.0 Network controller [0280]: Intel Corporation Wireless 8260 [8086:24f3] (rev 3a) Subsystem: Intel Corporation Dual Band Wireless-AC 8260 [8086:0010] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 279 Region 0: Memory at e1000000 (64-bit, non-prefetchable) [size=8K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi ** USB devices: Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 005: ID 05c8:0386 Cheng Uei Precision Industry Co., Ltd (Foxlink) Bus 001 Device 004: ID 138a:003f Validity Sensors, Inc. VFS495 Fingerprint Reader Bus 001 Device 003: ID 8087:0a2b Intel Corp. Bus 001 Device 002: ID 03f0:9d1d Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 9.6 APT prefers stable-updates APT policy: (500, 'stable-updates'), (500, 'stable-debug'), (500, 'proposed-updates'), (500, 'stable') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 4.9.0-8-amd64 (SMP w/4 CPU cores) Locale: LANG=en_GB.UTF-8, LC_CTYPE=en_GB.UTF-8 (charmap=UTF-8), LANGUAGE= (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) Versions of packages linux-image-4.9.0-8-amd64 depends on: ii initramfs-tools [linux-initramfs-tool] 0.130 ii kmod 23-2 ii linux-base 4.5 Versions of packages linux-image-4.9.0-8-amd64 recommends: ii firmware-linux-free 3.4 ii irqbalance 1.1.0-2.3 Versions of packages linux-image-4.9.0-8-amd64 suggests: pn debian-kernel-handbook <none> ii extlinux 3:6.03+dfsg-14.1+deb9u1 ii grub-pc 2.02~beta3-5+deb9u1 pn linux-doc-4.9 <none> Versions of packages linux-image-4.9.0-8-amd64 is related to: ii firmware-amd-graphics 20161130-4 pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-cavium <none> pn firmware-intel-sound <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> ii firmware-iwlwifi 20180825+dfsg-1~bpo9+1 pn firmware-libertas <none> ii firmware-linux-nonfree 20161130-4 ii firmware-misc-nonfree 20161130-4 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-realtek <none> pn firmware-samsung <none> pn firmware-siano <none> pn firmware-ti-connectivity <none> pn xen-hypervisor <none> -- no debconf information Cheers, -- Cyril Brulebois (k...@debian.org) <https://debamax.com/> D-I release manager -- Release team member -- Freelance Consultant