Package: linux-2.6
Version: 2.6.31-1
Severity: important
After upgrade to kernel 2.6.31 (from 2.6.30), wireless card stopped
working. It seems to be set up fine, associates with AP but it is unable
to communicate. Ping or any other network communication doesn't work.
After reboot to 2.6.30, everything works fine.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corp.
bios_version: DPP3510J.86A.0572.2009.0715.2346
board_vendor: Intel Corporation
board_name: DG33FB
board_version: AAD81072-303
** Network interface configuration:
### etherconf DEBCONF AREA. DO NOT EDIT THIS AREA OR INSERT TEXT BEFORE IT.
# /etc/network/interfaces -- configuration file for ifup(8), ifdown(8)
auto lo eth0 eth1 wlan0
# The loopback interface
iface lo inet loopback
# The ethernet interface, configured by etherconf
iface eth0 inet static
address 172.23.0.254
netmask 255.255.255.0
dns-nameservers 127.0.0.1
### END OF DEBCONF AREA. PLACE YOUR EDITS BELOW; THEY WILL BE PRESERVED.
# rozhrani pro pppoe
iface eth1 inet manual
up ifconfig $IFACE up
down ifconfig $IFACE down
iface dsl-provider inet ppp
provider dsl-provider
iface wlan0 inet static
address 172.23.255.129
netmask 255.255.255.0
gateway 172.23.255.254
dns-nameservers 172.23.255.254
wireless-essid DEVON
wireless-mode Managed
wireless-key restricted s:XXX
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82G33/G31/P35/P31 Express DRAM
Controller [8086:29c0] (rev 02)
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation 82G33/G31/P35/P31 Express PCI
Express Root Port [8086:29c1] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: e0300000-e03fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:02.0 Display controller [0380]: Intel Corporation 82G33/G31 Express
Integrated Graphics Controller [8086:29c2] (rev 02)
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e0400000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 4430 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at e0200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: <access denied>
00:03.0 Communication controller [0780]: Intel Corporation 82G33/G31/P35/P31
Express MEI Controller [8086:29c4] (rev 02)
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 11
Region 0: Memory at e04a6100 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:19.0 Ethernet controller [0200]: Intel Corporation 82566DC-2 Gigabit Network
Connection [8086:294c] (rev 02)
Subsystem: Intel Corporation Device [8086:0001]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 30
Region 0: Memory at e0480000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at e04a4000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 4400 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #4 [8086:2937] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 18
Region 4: I/O ports at 40e0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #5 [8086:2938] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 40c0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #6 [8086:2939] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 17
Region 4: I/O ports at 40a0 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1a.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #2 [8086:293c] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 17
Region 0: Memory at e04a5c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801I (ICH9 Family) HD Audio
Controller [8086:293e] (rev 02)
Subsystem: Intel Corporation Device [8086:0002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e04a0000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 1 [8086:2940] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 2 [8086:2942] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: e0100000-e01fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 3 [8086:2944] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.3 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 4 [8086:2946] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.4 PCI bridge [0604]: Intel Corporation 82801I (ICH9 Family) PCI Express
Port 5 [8086:2948] (rev 02) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=06, subordinate=06, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #1 [8086:2934] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 4080 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #2 [8086:2935] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 4060 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB UHCI
Controller #3 [8086:2936] (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 4040 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801I (ICH9 Family) USB2 EHCI
Controller #1 [8086:293a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at e04a5800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev
92) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
I/O behind bridge: 00001000-00001fff
Memory behind bridge: e0000000-e00fffff
Prefetchable memory behind bridge: 00000000e0500000-00000000e05fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801IH (ICH9DH) LPC Interface
Controller [8086:2912] (rev 02)
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 82801IR/IO/IH (ICH9R/DO/DH) 6
port SATA AHCI Controller [8086:2922] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 31
Region 0: I/O ports at 4428 [size=8]
Region 1: I/O ports at 443c [size=4]
Region 2: I/O ports at 4420 [size=8]
Region 3: I/O ports at 4438 [size=4]
Region 4: I/O ports at 4020 [size=32]
Region 5: Memory at e04a5000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 82801I (ICH9 Family) SMBus Controller
[8086:2930] (rev 02)
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 18
Region 0: Memory at e04a6000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 4000 [size=32]
Kernel driver in use: i801_smbus
01:00.0 VGA compatible controller [0300]: ATI Technologies Inc Mobility Radeon
HD 3600 Series [1002:9598] (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:01da]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 32
Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 2: Memory at e0300000 (64-bit, non-prefetchable) [size=64K]
Region 4: I/O ports at 3000 [size=256]
Expansion ROM at e0320000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
01:00.1 Audio device [0403]: ATI Technologies Inc RV635 Audio device [Radeon HD
3600 Series] [1002:aa20]
Subsystem: ASUSTeK Computer Inc. Device [1043:aa20]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at e0310000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
03:00.0 IDE interface [0101]: Marvell Technology Group Ltd. 88SE6101
single-port PATA133 interface [11ab:6101] (rev b1) (prog-if 8f [Master SecP
SecO PriP PriO])
Subsystem: Marvell Technology Group Ltd. 88SE6101 single-port PATA133
interface [11ab:6101]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 2018 [size=8]
Region 1: I/O ports at 2024 [size=4]
Region 2: I/O ports at 2010 [size=8]
Region 3: I/O ports at 2020 [size=4]
Region 4: I/O ports at 2000 [size=16]
Region 5: Memory at e0100000 (32-bit, non-prefetchable) [size=512]
Capabilities: <access denied>
Kernel driver in use: pata_marvell
07:00.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado]
[10b7:9200] (rev 74)
Subsystem: 3Com Corporation 3C905CX-TX/TX-M Fast Etherlink for PC
Management NIC [10b7:1000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 1000 [size=128]
Region 1: Memory at e000c800 (32-bit, non-prefetchable) [size=128]
Expansion ROM at e0500000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
07:01.0 Network controller [0280]: RaLink RT2561/RT61 802.11g PCI [1814:0301]
Subsystem: RaLink EW-7108PCg [1814:2561]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 22
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: rt61pci
07:02.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1
[1102:0002] (rev 08)
Subsystem: Creative Labs CT4832 SBLive! Value [1102:8027]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at 1080 [size=32]
Capabilities: <access denied>
Kernel driver in use: EMU10K1_Audigy
07:02.1 Input device controller [0980]: Creative Labs SB Live! Game Port
[1102:7002] (rev 08)
Subsystem: Creative Labs Gameport Joystick [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at 10a0 [size=8]
Capabilities: <access denied>
Kernel driver in use: Emu10k1_gameport
07:03.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB22/A
IEEE-1394a-2000 Controller (PHY/Link) [104c:8023] (prog-if 10 [OHCI])
Subsystem: Intel Corporation Device [8086:5044]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at e000c000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at e0008000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: firewire_ohci
** USB devices:
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 1131:1001 Integrated System Solution Corp. KY-BT100
Bluetooth Adapter
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 002: ID 046d:c049 Logitech, Inc. G5 Laser Mouse
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 005: ID 05e3:0606 Genesys Logic, Inc. USB 2.0 Hub / D-Link
DUB-H4 USB 2.0 Hub
Bus 001 Device 006: ID 045e:003c Microsoft Corp. SideWinder Joystick
Bus 001 Device 003: ID 0424:2514 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (990, 'unstable'), (400, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.30-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=cs_CZ.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.31-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs
ii module-init-tools 3.11-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.31-1-amd64 recommends:
ii firmware-linux-free 2.6.31-1 Binary firmware for various driver
Versions of packages linux-image-2.6.31-1-amd64 suggests:
pn grub | lilo <none> (no description available)
pn linux-doc-2.6.31 <none> (no description available)
Versions of packages linux-image-2.6.31-1-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
ii firmware-linux 0.21 Binary firmware for various driver
ii firmware-linux-nonfree 0.21 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
ii firmware-ralink 0.21 Binary firmware for Ralink RT2561,
-- debconf information:
* linux-image-2.6.31-1-amd64/postinst/missing-firmware-2.6.31-1-amd64:
linux-image-2.6.31-1-amd64/postinst/bootloader-error-2.6.31-1-amd64:
linux-image-2.6.31-1-amd64/prerm/removing-running-kernel-2.6.31-1-amd64: true
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.31-1-amd64/prerm/would-invalidate-boot-loader-2.6.31-1-amd64:
true
linux-image-2.6.31-1-amd64/postinst/depmod-error-initrd-2.6.31-1-amd64: false
linux-image-2.6.31-1-amd64/postinst/bootloader-test-error-2.6.31-1-amd64:
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
