Package: linux-2.6 Version: 2.6.32-9 Severity: normal Hi,
Going from 2.6.30 to 2.6.32, I can no longer mount my LVM-based partition on my secondary harddisk, I get the following error when I try to run e.g. vgchange: nighthawk~$ LANG=C sudo vgchange -a y 2 logical volume(s) in volume group "nighthawk" now active device-mapper: resume ioctl failed: Invalid argument Unable to resume data-data (254:3) 1 logical volume(s) in volume group "data" now active nighthawk~$ sudo mount /dev/mapper/data-data /mnt mount: /dev/mapper/data-data already mounted or /mnt busy This is the corresponding kernel error in syslog: Apr 18 15:17:02 nighthawk kernel: [ 20.713326] device-mapper: table: 254:3: hdc too small for target: start=384, len=78135296, dev_size=71762930 It turns out this is because contrary to linux-image-2.6.30-2-686, 2.6.32 does not disable HPA: 2.6.30: Apr 18 15:11:09 nighthawk kernel: [ 3.727599] hdc: max request size: 128KiB Apr 18 15:11:09 nighthawk kernel: [ 3.727939] hdc: Host Protected Area detected. Apr 18 15:11:09 nighthawk kernel: [ 3.727940] current capacity is 71762930 sectors (36742 MB) Apr 18 15:11:09 nighthawk kernel: [ 3.727941] native capacity is 78140160 sectors (40007 MB) Apr 18 15:11:09 nighthawk kernel: [ 3.728303] hdc: Host Protected Area disabled. Apr 18 15:11:09 nighthawk kernel: [ 3.728307] hdc: 78140160 sectors (40007 MB) w/7877KiB Cache, CHS=65535/16/63 Apr 18 15:11:09 nighthawk kernel: [ 3.728627] hdc: cache flushes supported Apr 18 15:11:09 nighthawk kernel: [ 3.728653] hdc: unknown partition table 2.6.32: Apr 18 15:17:02 nighthawk kernel: [ 3.768973] hdc: max request size: 128KiB Apr 18 15:17:02 nighthawk kernel: [ 3.769303] hdc: Host Protected Area detected. Apr 18 15:17:02 nighthawk kernel: [ 3.769305] current capacity is 71762930 sectors (36742 MB) Apr 18 15:17:02 nighthawk kernel: [ 3.769306] native capacity is 78140160 sectors (40007 MB) Apr 18 15:17:02 nighthawk kernel: [ 3.769309] hdc: 71762930 sectors (36742 MB) w/7877KiB Cache, CHS=65535/16/63 Apr 18 15:17:02 nighthawk kernel: [ 3.769639] hdc: cache flushes supported Going back to an earlier 2.6.32 (like 2.6.32-trunk-686) does not help, I need to revert to 2.6.30 (did not check 2.6.31). Michael -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information not available ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82855PM Processor to I/O Controller [8086:3340] (rev 03) Subsystem: IBM Thinkpad T40 series [1014:0529] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Region 0: Memory at d0000000 (32-bit, prefetchable) [size=256M] Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:01.0 PCI bridge [0604]: Intel Corporation 82855PM Processor to AGP Controller [8086:3341] (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 96 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 00003000-00003fff Memory behind bridge: c0100000-c01fffff Prefetchable memory behind bridge: e0000000-e7ffffff Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:1d.0 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 [8086:24c2] (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM ThinkPad [1014:052d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 4: I/O ports at 1800 [size=32] Kernel driver in use: uhci_hcd 00:1d.1 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 [8086:24c4] (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM ThinkPad [1014:052d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at 1820 [size=32] Kernel driver in use: uhci_hcd 00:1d.2 USB Controller [0c03]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 [8086:24c7] (rev 01) (prog-if 00 [UHCI]) Subsystem: IBM ThinkPad [1014:052d] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 11 Region 4: I/O ports at 1840 [size=32] Kernel driver in use: uhci_hcd 00:1d.7 USB Controller [0c03]: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller [8086:24cd] (rev 01) (prog-if 20 [EHCI]) Subsystem: IBM ThinkPad [1014:052e] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=1K] Capabilities: <access denied> Kernel driver in use: ehci_hcd 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev 81) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR+ INTx- Latency: 0 Bus: primary=00, secondary=02, subordinate=08, sec-latency=168 I/O behind bridge: 00004000-00008fff Memory behind bridge: c0200000-cfffffff Prefetchable memory behind bridge: e8000000-efffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:1f.0 ISA bridge [0601]: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge [8086:24cc] (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.1 IDE interface [0101]: Intel Corporation 82801DBM (ICH4-M) IDE Controller [8086:24ca] (rev 01) (prog-if 8a [Master SecP PriP]) Subsystem: IBM ThinkPad [1014:052d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 01f0 [size=8] Region 1: I/O ports at 03f4 [size=1] Region 2: I/O ports at 0170 [size=8] Region 3: I/O ports at 0374 [size=1] Region 4: I/O ports at 1860 [size=16] Region 5: Memory at 80000000 (32-bit, non-prefetchable) [size=1K] Kernel driver in use: PIIX_IDE 00:1f.3 SMBus [0c05]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller [8086:24c3] (rev 01) Subsystem: IBM ThinkPad [1014:052d] Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at 1880 [size=32] Kernel driver in use: i801_smbus 00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller [8086:24c5] (rev 01) Subsystem: IBM ThinkPad T41 [1014:0537] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 0: I/O ports at 1c00 [size=256] Region 1: I/O ports at 18c0 [size=64] Region 2: Memory at c0000c00 (32-bit, non-prefetchable) [size=512] Region 3: Memory at c0000800 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: Intel ICH 00:1f.6 Modem [0703]: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller [8086:24c6] (rev 01) (prog-if 00 [Generic]) Subsystem: IBM Device [1014:055a] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 11 Region 0: I/O ports at 2400 [size=256] Region 1: I/O ports at 2000 [size=128] Capabilities: <access denied> Kernel driver in use: Intel ICH Modem 01:00.0 VGA compatible controller [0300]: ATI Technologies Inc RV350 [Mobility Radeon 9600 M10] [1002:4e50] (prog-if 00 [VGA controller]) Subsystem: IBM Device [1014:0550] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B+ DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 66 (2000ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at e0000000 (32-bit, prefetchable) [size=128M] Region 1: I/O ports at 3000 [size=256] Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K] [virtual] Expansion ROM at c0120000 [disabled] [size=128K] Capabilities: <access denied> 02:00.0 CardBus bridge [0607]: Texas Instruments PCI4520 PC card Cardbus Controller [104c:ac46] (rev 01) Subsystem: IBM ThinkPad [1014:0552] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at b0000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: e8000000-ebfff000 (prefetchable) Memory window 1: c4000000-c7fff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus 02:00.1 CardBus bridge [0607]: Texas Instruments PCI4520 PC card Cardbus Controller [104c:ac46] (rev 01) Subsystem: IBM ThinkPad [1014:0552] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 11 Region 0: Memory at b1000000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=07, subordinate=07, sec-latency=176 Memory window 0: ec000000-effff000 (prefetchable) Memory window 1: c8000000-cbfff000 I/O window 0: 00004800-000048ff I/O window 1: 00004c00-00004cff BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ 16-bit legacy interface ports at 0001 Kernel driver in use: yenta_cardbus 02:01.0 Ethernet controller [0200]: Intel Corporation 82540EP Gigabit Ethernet Controller (Mobile) [8086:101e] (rev 03) Subsystem: IBM Thinkpad [1014:0549] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (63750ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at c0220000 (32-bit, non-prefetchable) [size=128K] Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=64K] Region 2: I/O ports at 8000 [size=64] [virtual] Expansion ROM at c0240000 [disabled] [size=64K] Capabilities: <access denied> Kernel driver in use: e1000 02:02.0 Ethernet controller [0200]: Atheros Communications Inc. AR5212 802.11abg NIC [168c:1014] (rev 01) Subsystem: Phillips Components Device [17ab:8331] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: Memory at c0210000 (32-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: ath5k ** USB devices: Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: squeeze/sid Architecture: i386 (i686) Kernel: Linux 2.6.32-trunk-686 (SMP w/1 CPU core) Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-2.6.32-3-686 depends on: ii debconf [debconf-2.0] 1.5.28 Debian configuration management sy ii initramfs-tools [linux-initra 0.93.4 tools for generating an initramfs ii module-init-tools 3.11-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-3-686 recommends: ii firmware-linux-free 2.6.32-5 Binary firmware for various driver ii libc6-i686 2.10.2-2 GNU C Library: Shared libraries [i Versions of packages linux-image-2.6.32-3-686 suggests: pn grub | lilo <none> (no description available) pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-3-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) ii firmware-linux-nonfree 0.22 Binary firmware for various driver pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) -- debconf information: shared/kernel-image/really-run-bootloader: true linux-image-2.6.32-3-686/postinst/bootloader-error-2.6.32-3-686: linux-image-2.6.32-3-686/postinst/depmod-error-initrd-2.6.32-3-686: false linux-image-2.6.32-3-686/postinst/bootloader-test-error-2.6.32-3-686: linux-image-2.6.32-3-686/postinst/missing-firmware-2.6.32-3-686: linux-image-2.6.32-3-686/prerm/would-invalidate-boot-loader-2.6.32-3-686: true linux-image-2.6.32-3-686/prerm/removing-running-kernel-2.6.32-3-686: true -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org