Package: linux-2.6 Version: 2.6.32-18 Severity: normal
When using 2.6.32-5-686 Linux kernel (package version 2.6.32-18) IDE controller
doesn't seem to be using DMA (about 4MB/sec from hdparm disk read).
When booted older kernel 2.6.32-3-686 which uses old ide modules, promise IDE
works flawlessly.
Attached dmesg-s from both kernels
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
not available
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host
bridge [8086:7190] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
Kernel modules: intel-agp
00:01.0 PCI bridge [0604]: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP
bridge [8086:7191] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d8000000-dfffffff
Prefetchable memory behind bridge: 38000000-380fffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Kernel modules: shpchp
00:07.0 ISA bridge [0601]: Intel Corporation 82371AB/EB/MB PIIX4 ISA
[8086:7110] (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:07.1 IDE interface [0101]: Intel Corporation 82371AB/EB/MB PIIX4 IDE
[8086:7111] (rev 01) (prog-if 80 [Master])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Kernel driver in use: PIIX_IDE
Kernel modules: piix
00:07.2 USB Controller [0c03]: Intel Corporation 82371AB/EB/MB PIIX4 USB
[8086:7112] (rev 01) (prog-if 00 [UHCI])
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin D routed to IRQ 10
Region 4: I/O ports at b000 [size=32]
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:07.3 Bridge [0680]: Intel Corporation 82371AB/EB/MB PIIX4 ACPI [8086:7113]
(rev 02)
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 9
Kernel modules: i2c-piix4
00:0c.0 Mass storage controller [0180]: Promise Technology, Inc. PDC20262
(FastTrak66/Ultra66) [105a:4d38] (rev 01)
Subsystem: Promise Technology, Inc. Ultra66 [105a:4d33]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at b400 [size=8]
Region 1: I/O ports at b800 [size=4]
Region 2: I/O ports at bc00 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at c400 [size=64]
Region 5: Memory at e8100000 (32-bit, non-prefetchable) [size=128K]
Expansion ROM at e4000000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: Promise_Old_IDE
Kernel modules: pdc202xx_old
00:0e.0 RAID bus controller [0104]: Silicon Image, Inc. PCI0680 Ultra ATA-133
Host Controller [1095:0680] (rev 02)
Subsystem: Silicon Image, Inc. SiI 0680 ATA/133 Controller [1095:0680]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 4 bytes
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at c800 [size=8]
Region 1: I/O ports at cc00 [size=4]
Region 2: I/O ports at d000 [size=8]
Region 3: I/O ports at d400 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at e8122000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at e5000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: SiI_IDE
Kernel modules: siimage
00:10.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet
Pro 100 [8086:1229] (rev 08)
Subsystem: IBM 10/100 EtherJet Management Adapter [1014:305c]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 12
Region 0: Memory at e8120000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at dc00 [size=64]
Region 2: Memory at e8000000 (32-bit, non-prefetchable) [size=1M]
Expansion ROM at e6000000 [disabled] [size=1M]
Capabilities: <access denied>
Kernel driver in use: e100
Kernel modules: e100
00:11.0 Ethernet controller [0200]: 3Com Corporation 3c900B-Combo Etherlink XL
[Cyclone] [10b7:9005] (rev 04)
Subsystem: 3Com Corporation 3C900B-Combo Etherlink XL Combo [10b7:9005]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (2500ns min, 12000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e000 [size=128]
Region 1: Memory at e8121000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at e7000000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: 3c59x
Kernel modules: 3c59x
01:00.0 VGA compatible controller [0300]: S3 Inc. Trio 64 3D [5333:8904] (rev
01) (prog-if 00 [VGA controller])
Subsystem: S3 Inc. 86C365 Trio3D AGP [5333:8904]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1000ns min, 63750ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d8000000 (32-bit, non-prefetchable) [size=64M]
[virtual] Expansion ROM at 38000000 [disabled] [size=64K]
Capabilities: <access denied>
** USB devices:
not available
-- System Information:
Debian Release: 5.0.5
APT prefers stable
APT policy: (500, 'stable'), (100, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-3-686 (SMP w/1 CPU core)
Locale: LANG=pl_PL.UTF-8, LC_CTYPE=pl_PL.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.97.2 tools for generating an initramfs
ii linux-base 2.6.32-18 Linux image base package
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-18 Binary firmware for various driver
ii libc6-i686 2.11.2-2 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
ii firmware-linux-nonfree 0.26 Binary firmware for various driver
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/prerm/would-invalidate-boot-loader-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/bootloader-test-error-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/bootloader-error-2.6.32-5-686:
dmesg-2.6.32-5-686.gz
Description: GNU Zip compressed data
dmesg-2.6.32-3-686.gz
Description: GNU Zip compressed data
