On Sat, Aug 20, 2005 at 08:54:04AM +0200, Bastian Blank wrote: > On Thu, Aug 18, 2005 at 07:52:21AM +0100, Paul Brossier wrote: > > while trying to boot 2.6.12 on a g5, it get to the following screen dump > > and the boot stops there. the fan starts spinning, and the machine > > reboots (after about the time it took me to type the following lines, > > including half of the first one) > > Please set panic_timeout on the commandline to a higher value and show > the last lines of the output,.
well, panic_timeout=100000000000 does not seem to make a big difference, but after trying to boot a few times i get the time to type all the screen. sorry for the typos if any :) i hope this helps, let me know. cheers, piem ------- begin manual screen dump ------- cf0000015 Setup Done Starting Linux PPC64 2.6.12-1-powerpc64 ----------------------------------------------------- ppc64_pft_size = 0x17 ppc64_debug_switch = 0x1 ppc64_interrupt_controller = 0x1 systemcfg = 0xc00000000035c00 systemcfg->platform = 0x400 systemcfg->processorCount = 0x2 systemcfg->physicalMemorySize = 0x20000000 ppc64_caches.dcache_line_size = 0x80 ppc64_caches.icache_line_size = 0x80 htab_address = 0xc00000001f000000 htab_hash_mask = 0xffff ----------------------------------------------------- [boot]0100 MM Init [boot]0100 MM Init Done Linux version 2.6.12-1-powerpc64 ([EMAIL PROTECTED]) (gcc version 4.0.2 20050806 (prerelease) (Debian 4.0.1-4)) #1 SMP Tue Aug 16 20:21:34 UTC 2005 [boot]0012 Setup Arch Top of RAM: 0x20000000, Total RAM: 0x20000000 Memory hole size: 0MB Syscall map setup, 242 32 bits and 220 64 bits syscalls Found U3 memory controller & host bridge, revision: 179 Mapped at 0xe000000080180000 Found a K2 mac-io controller, rev: 96, mapped at 0xe0000000801c1000 PowerMac motherboard: PowerMac G5 via-pmu: Server Mode is disabled PMU driver 2 initialized for Core99, firmware: 0c nvram: Checking bank 0... nvram: gen0=262, gen1=263 nvram: Active bank is: 1 Adding PCI host bridge /[EMAIL PROTECTED],f0000000 Found U3-AGP PCI host bridge. Firmware bus number: 240->255 Adding PCI host bridge /[EMAIL PROTECTED],f2000000 Can't get bus-range for /[EMAIL PROTECTED],f2000000, assume bus 0 U3/HT: hole, 0 end at 8fffffff, 1 start at a0000000 Found U3-HT PCI host bridge. Firmware bus number: 0->239 Can't get bus-range for /[EMAIL PROTECTED],f2000000 PCI Host 0, io start: fffffffffd800000; io end: fffffffffdffffff PCI Host 0, io start: 0; io end: 3fffff Using native/NAP idle loop [boot]0015 Setup Done Built 1 zonelists Kernel command line: root=/dev/sda4 ro devfs=mount panic_timeout=10000000000 PowerMac using OpenPIC irq controller at 0x80040000 mpic: Setting up MPIC " K2-MPIC " version 1.2 at 80040000, max 4 CPUs mpic: ISU size: 120, shift: 7, mask 7f mpic: Initializing for 120 sources Slave OpenPIC at 0xf8040000 hooked on IRQ 56 mpic: Setting up MPIC " U3-MPIC " version 1.2 at f8040000, max 4 CPUs mpic: ISU size: 120, shift: 7, mask 7f mpic: Initializing for 120 sources PID hash table entries: 4096 (order: 12, 131072 bytes) time_init: decrementer frequency = 33.333333 MHz smp_core99_probe smp_core99_kick_cpu smp_core99_kick_cpu done smp_core99_setup_cpu 0 done Linux ppc64 2.6.12-1-powerpc64 ------- end manual screen dump ------- -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]