Here it is:
result from lspci -vv:
---------
03:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n
Wireless LAN Controller (rev 01)
Subsystem: Broadcom Corporation Device 051a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d0300000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Vendor Specific Information: Len=78 <?>
Capabilities: [48] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1
unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<4us, L1 <64us
ClockPM+ Surprise- LLActRep+ BwNot-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- Retrain-
CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+
BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [13c v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 00-00-2c-ff-ff-4e-88-25
Capabilities: [16c v1] Power Budgeting <?>
-------------------
and result from dmesg:
--------
[ 330.205983] brcm80211: module is from the staging directory, the
quality is unknown, you have been warned.
[ 330.212186] brcm80211 0000:03:00.0: PCI INT A -> GSI 17 (level,
low) -> IRQ 17
[ 330.212195] brcm80211 0000:03:00.0: setting latency timer to 64
[ 330.268237] Found chip type AI (0x13814313)
[ 330.271328] Changing max_res_mask to 0xffff
[ 330.271330] Changing min_res_mask to 0x200d
[ 330.277446] Applying 4313 WARs
[ 330.278330] wlc_bmac_attach:: deviceid 0x4727 nbands 1 board 0x51a
macaddr: 88:25:2c:4e:9e:34
[ 330.283578] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht'
[ 330.285363] wl_set_hint: Sending country code US to MAC80211
[ 330.285371] wl0: Broadcom BCM43xx 802.11 MAC80211 Driver (1.82.8.0)
(Compiled at 04:19:31 on Apr 7 2011)
[ 330.365121] ADDRCONF(NETDEV_UP): wlan0: link is not ready
----------------------
By the way, before I used 'modprobe cfg80211 ieee80211_regdom=EU' .
Perhaps the problem comes from that and line (dmesg) 330.285363 ? I
need channel 13 ...
Best regards and thanks,
Wenceslao
maximilian attems <m...@stro.at> ha escrito:
reassign 622842 linux-2.6
stop
On Fri, Apr 15, 2011 at 09:07:30AM +0200, Wenceslao wrote:
Package: firmware-brcm80211
Version: 0.29
Severity: important
module brcm80211 is not getting the associated point of a wifi,
although it is
properly detected. With a usb wifi stick (a ralink one) is detecting and
attaching properly.
so you properly know the module and report against firmware, *woow*.
attach relevant dmesg or lspci output unless proven as currently this can
be close right away.
kind regards
--
maks
----------------------------------------------------------------
Este mensaje ha sido enviado desde https://webmail.unav.es
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
