On Thu, Sep 29, 2011 at 04:35:31PM +0200, Bart Hartgers wrote:
>
> If you have a breakout-box, it would also be interesting to 'manually'
> toggle some signals, basically just short rxd and/or cts to gnd for a
> sec.
> That should trigger some messages in the log if the ark3116 module is
> loaded with debug=1.
Some more results using the breakout box and a multimeter:
1) Garmin gps only connected;
pin 2 (tx on gps) : -5.57 V
pin 3 (rx on gps) : -0.64 V
pin 2 (gps tx) pulls down to -3.26V with 245 \ohm and to -1.95V with
100 \ohm to grnd (pin 5).
-------------------------------------------------------------------------------
2) Ark converter only:
pin 2 (tx on gps, so rx on ark): 0.01V
pin 3 (rx on gps) : 0.04V
(Same results on both working & failing kernel, module loaded).
-------------------------------------------------------------------------------
3) Both ark and garmin attached and working.
pin 2 (tx on gps) : 0.01V on module load
pin 3 (rx on gps) : -5.52V on module load
-----------------------------------------------------
Using gpsbabel under the old working kernel 2.6.32,
activity is seen on both pins 2 & 3 (as expected): just multimeter at
this stage.
No activity visible with multimeter under the 3.0.0 kernel.
-----------------------------------------------------------
Pulling down pin 2 (tx on gps, rx on ark) to grnd via 100 \ohm on
working kernel with debug=1 gives
Oct 1 17:17:49 elf kernel: [ 259.932936]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
003 > ok
Oct 1 17:17:49 elf kernel: [ 259.933521]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
004 > ok
Oct 1 17:17:49 elf kernel: [ 259.934542]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
005 > ok
Oct 1 17:17:49 elf kernel: [ 259.935536]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
006 > ok
Oct 1 17:17:49 elf kernel: [ 259.937855]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
007 < 1 bytes [0x03]
Oct 1 17:17:49 elf kernel: [ 259.938541]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
008 > ok
Oct 1 17:17:49 elf kernel: [ 259.939534]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
009 > ok
Oct 1 17:17:49 elf kernel: [ 259.941517]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
010 > ok
Oct 1 17:17:49 elf kernel: [ 259.942629]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
011 > ok
Oct 1 17:17:49 elf kernel: [ 259.943545]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
012 < 1 bytes [0x03]
Oct 1 17:17:49 elf kernel: [ 259.944520]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
013 > ok
Oct 1 17:17:49 elf kernel: [ 259.946321]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
014 < 1 bytes [0x00]
Oct 1 17:17:49 elf kernel: [ 259.946529]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
015 > ok
Oct 1 17:17:49 elf kernel: [ 259.947543]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
016 < 1 bytes [0x00]
Oct 1 17:17:49 elf kernel: [ 259.949517]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
017 > ok
Oct 1 17:17:49 elf kernel: [ 259.950526]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
018 < 1 bytes [0x01]
Oct 1 17:17:49 elf kernel: [ 259.951526]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
019 > ok
Oct 1 17:17:49 elf kernel: [ 259.952526]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
020 < 1 bytes [0xB0]
Oct 1 17:17:49 elf kernel: [ 259.953529]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:17:49 elf kernel: [ 259.954542]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:17:49 elf kernel: [ 259.955537]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:17:49 elf kernel: [ 259.956517]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:17:49 elf kernel: [ 259.957522]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:17:49 elf kernel: [ 259.958516]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:17:49 elf kernel: [ 259.959522]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:17:49 elf kernel: [ 259.960535]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
-----------------------------------------------------------------------------------------------------------------
Actually, I suspect that the messages above did not include any response
from the pull down.
Another direct short from pin 2 to ground also gave no debug messages.
So it looks as if those experiments are not going to give anything
useful. I could try on the failing kernel if it would be helpful,
or perhaps look at some of the unconnected signals on the ark.
While I am at it, here are the signals on some of the other pins (ark
and gps connected and working on the old kernel)
Pin 1: -1.72V
pin 4: -1.72V
pin 6: -1.72V
pin 7: -1.72V
pin 8: -1.72V
pin 9: -1.72V
------------------------------------------------------------------------------------------------------------
4) Shorting pin 4 (rts?) to ground does give debug output (old working
kernel)
-------------------------------------------------------------
Oct 1 17:51:35 elf kernel: [ 2286.317028]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_open - port 0
Oct 1 17:51:35 elf kernel: [ 2286.318755]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
111 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.319745]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
112 > ok
Oct 1 17:51:35 elf kernel: [ 2286.320745]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
113 > ok
Oct 1 17:51:35 elf kernel: [ 2286.321746]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
114 > ok
Oct 1 17:51:35 elf kernel: [ 2286.323160]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
115 > ok
Oct 1 17:51:35 elf kernel: [ 2286.323951]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
116 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.324980]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
117 > ok
Oct 1 17:51:35 elf kernel: [ 2286.325749]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
118 < 1 bytes [0x02]
Oct 1 17:51:35 elf kernel: [ 2286.326744]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
119 > ok
Oct 1 17:51:35 elf kernel: [ 2286.327749]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
120 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.329199]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
121 > ok
Oct 1 17:51:35 elf kernel: [ 2286.329748]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
122 < 1 bytes [0x01]
Oct 1 17:51:35 elf kernel: [ 2286.331826]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
123 > ok
Oct 1 17:51:35 elf kernel: [ 2286.332970]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
124 < 1 bytes [0xB0]
Oct 1 17:51:35 elf kernel: [ 2286.332994]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.333049]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.333067]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.333086]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.333748]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x02]
Oct 1 17:51:35 elf kernel: [ 2286.333769]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.334740]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.335744]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.336719]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.337717]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.338720]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.339721]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.339732]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.340719]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.341716]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.341754]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.341786]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.341797]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:35 elf kernel: [ 2286.341809]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.341816]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.341822]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.341828]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.342720]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.342731]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.343715]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.344716]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.345718]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.346719]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.347719]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.348715]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.348726]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.349723]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.350716]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.350737]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.350765]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x540b not supported
Oct 1 17:51:35 elf kernel: [ 2286.523344]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.523369]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:35 elf kernel: [ 2286.523392]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.523405]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.523417]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.523430]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.523734]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.523750]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.524727]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.525830]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.526735]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.527727]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.529246]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.529723]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.529743]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.530732]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.531731]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.531772]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.532843]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_open - port 0
Oct 1 17:51:35 elf kernel: [ 2286.533729]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
111 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.534732]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
112 > ok
Oct 1 17:51:35 elf kernel: [ 2286.535725]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
113 > ok
Oct 1 17:51:35 elf kernel: [ 2286.536721]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
114 > ok
Oct 1 17:51:35 elf kernel: [ 2286.537726]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
115 > ok
Oct 1 17:51:35 elf kernel: [ 2286.538722]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
116 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.539728]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
117 > ok
Oct 1 17:51:35 elf kernel: [ 2286.540708]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
118 < 1 bytes [0x02]
Oct 1 17:51:35 elf kernel: [ 2286.541707]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
119 > ok
Oct 1 17:51:35 elf kernel: [ 2286.542705]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
120 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.543707]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
121 > ok
Oct 1 17:51:35 elf kernel: [ 2286.544711]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
122 < 1 bytes [0x01]
Oct 1 17:51:35 elf kernel: [ 2286.545708]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
123 > ok
Oct 1 17:51:35 elf kernel: [ 2286.546705]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
124 < 1 bytes [0xB0]
Oct 1 17:51:35 elf kernel: [ 2286.546717]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.546728]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.546737]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.546746]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.547701]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x02]
Oct 1 17:51:35 elf kernel: [ 2286.547712]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.548722]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.549701]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.550706]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.551708]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.552708]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.553705]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.553715]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.554704]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.555700]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.555727]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.555746]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.555756]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:35 elf kernel: [ 2286.555768]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.555775]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.555781]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.555787]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.556705]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.556713]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.557702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.558700]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.559702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.560705]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.561706]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.562707]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.562718]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.563703]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.564702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.564723]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.598749]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.598762]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:35 elf kernel: [ 2286.598774]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.598781]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.598787]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.598793]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.599748]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.599763]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.600699]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.601728]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.602724]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.603715]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.604725]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.605720]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.605740]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.606721]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.607718]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.607755]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.608859]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_open - port 0
Oct 1 17:51:35 elf kernel: [ 2286.609720]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
111 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.610742]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
112 > ok
Oct 1 17:51:35 elf kernel: [ 2286.611718]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
113 > ok
Oct 1 17:51:35 elf kernel: [ 2286.612703]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
114 > ok
Oct 1 17:51:35 elf kernel: [ 2286.613698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
115 > ok
Oct 1 17:51:35 elf kernel: [ 2286.614698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
116 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.615704]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
117 > ok
Oct 1 17:51:35 elf kernel: [ 2286.616703]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
118 < 1 bytes [0x02]
Oct 1 17:51:35 elf kernel: [ 2286.617697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
119 > ok
Oct 1 17:51:35 elf kernel: [ 2286.618700]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
120 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.619698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
121 > ok
Oct 1 17:51:35 elf kernel: [ 2286.620702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
122 < 1 bytes [0x01]
Oct 1 17:51:35 elf kernel: [ 2286.621698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
123 > ok
Oct 1 17:51:35 elf kernel: [ 2286.622698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
124 < 1 bytes [0xB0]
Oct 1 17:51:35 elf kernel: [ 2286.622710]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.622720]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.622729]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.622738]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.623701]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x02]
Oct 1 17:51:35 elf kernel: [ 2286.623712]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.624700]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.625697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.626697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.627696]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.628702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.629697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.629707]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.630697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.631698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.631729]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.631748]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:35 elf kernel: [ 2286.631763]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:35 elf kernel: [ 2286.631778]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:35 elf kernel: [ 2286.631785]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:35 elf kernel: [ 2286.631791]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:35 elf kernel: [ 2286.631797]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:35 elf kernel: [ 2286.632700]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.632711]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:35 elf kernel: [ 2286.633697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:35 elf kernel: [ 2286.634698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:35 elf kernel: [ 2286.635694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:35 elf kernel: [ 2286.636697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:35 elf kernel: [ 2286.637701]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:35 elf kernel: [ 2286.638694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:35 elf kernel: [ 2286.638705]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:35 elf kernel: [ 2286.639697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:35 elf kernel: [ 2286.640695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:35 elf kernel: [ 2286.640711]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2286.683656]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2286.683674]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:36 elf kernel: [ 2286.684716]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:36 elf kernel: [ 2286.684728]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:36 elf kernel: [ 2286.684737]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:36 elf kernel: [ 2286.684746]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:36 elf kernel: [ 2286.685725]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.685747]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:36 elf kernel: [ 2286.686721]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:36 elf kernel: [ 2286.687708]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:36 elf kernel: [ 2286.688713]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:36 elf kernel: [ 2286.689709]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:36 elf kernel: [ 2286.690717]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.691713]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:36 elf kernel: [ 2286.691735]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:36 elf kernel: [ 2286.692724]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:36 elf kernel: [ 2286.693711]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:36 elf kernel: [ 2286.693750]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2286.694874]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_open - port 0
Oct 1 17:51:36 elf kernel: [ 2286.695710]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
111 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.696699]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
112 > ok
Oct 1 17:51:36 elf kernel: [ 2286.697698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
113 > ok
Oct 1 17:51:36 elf kernel: [ 2286.698695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
114 > ok
Oct 1 17:51:36 elf kernel: [ 2286.699695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
115 > ok
Oct 1 17:51:36 elf kernel: [ 2286.700698]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
116 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.701692]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
117 > ok
Oct 1 17:51:36 elf kernel: [ 2286.702695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
118 < 1 bytes [0x02]
Oct 1 17:51:36 elf kernel: [ 2286.703691]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
119 > ok
Oct 1 17:51:36 elf kernel: [ 2286.704695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
120 < 1 bytes [0x00]
Oct 1 17:51:36 elf kernel: [ 2286.705694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
121 > ok
Oct 1 17:51:36 elf kernel: [ 2286.706697]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
122 < 1 bytes [0x01]
Oct 1 17:51:36 elf kernel: [ 2286.707690]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
123 > ok
Oct 1 17:51:36 elf kernel: [ 2286.708695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
124 < 1 bytes [0xB0]
Oct 1 17:51:36 elf kernel: [ 2286.708707]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:36 elf kernel: [ 2286.708717]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:36 elf kernel: [ 2286.708726]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:36 elf kernel: [ 2286.708736]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:36 elf kernel: [ 2286.709694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x02]
Oct 1 17:51:36 elf kernel: [ 2286.709702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:36 elf kernel: [ 2286.710690]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:36 elf kernel: [ 2286.711692]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:36 elf kernel: [ 2286.712695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:36 elf kernel: [ 2286.713695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:36 elf kernel: [ 2286.714690]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.715691]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:36 elf kernel: [ 2286.715702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:36 elf kernel: [ 2286.716694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:36 elf kernel: [ 2286.717692]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:36 elf kernel: [ 2286.717722]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2286.717740]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2286.717755]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:36 elf kernel: [ 2286.717771]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:36 elf kernel: [ 2286.717781]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:36 elf kernel: [ 2286.717790]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:36 elf kernel: [ 2286.717799]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:36 elf kernel: [ 2286.718692]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.718703]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:36 elf kernel: [ 2286.719691]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:36 elf kernel: [ 2286.720694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:36 elf kernel: [ 2286.721694]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:36 elf kernel: [ 2286.722695]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:36 elf kernel: [ 2286.723692]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2286.724691]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:36 elf kernel: [ 2286.724702]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:36 elf kernel: [ 2286.725696]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:36 elf kernel: [ 2286.726690]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:36 elf kernel: [ 2286.726712]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2287.169349]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
Oct 1 17:51:36 elf kernel: [ 2287.169375]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5404 not supported
Oct 1 17:51:36 elf kernel: [ 2287.169728]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_set_termios - port 0
Oct 1 17:51:36 elf kernel: [ 2287.169744]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting CS8
Oct 1 17:51:36 elf kernel: [ 2287.169756]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting parity to NONE
Oct 1 17:51:36 elf kernel: [ 2287.169768]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting 1 stop bit
Oct 1 17:51:36 elf kernel: [ 2287.170708]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
000 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2287.170723]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
setting baudrate to 9600 (->reg=312)
Oct 1 17:51:36 elf kernel: [ 2287.171691]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
147 > ok
Oct 1 17:51:36 elf kernel: [ 2287.176086]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
148 > ok
Oct 1 17:51:36 elf kernel: [ 2287.176686]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
149 > ok
Oct 1 17:51:36 elf kernel: [ 2287.177661]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
150 > ok
Oct 1 17:51:36 elf kernel: [ 2287.178794]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
151 < 1 bytes [0x03]
Oct 1 17:51:36 elf kernel: [ 2287.179657]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
152 > ok
Oct 1 17:51:36 elf kernel: [ 2287.179668]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
updating bit count, stop bit or parity (cfg=0x03)
Oct 1 17:51:36 elf kernel: [ 2287.180664]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
153 < 1 bytes [0x00]
Oct 1 17:51:36 elf kernel: [ 2287.181658]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
154 > ok
Oct 1 17:51:36 elf kernel: [ 2287.181682]
/tmp/buildd/linux-2.6-2.6.32/debian/build/source_i386_none/drivers/usb/serial/ark3116.c:
ark3116_ioctl cmd 0x5401 not supported
--------------------------------------------------------------------------------------------------------------
I will report what happens on shorting pin 4 under kernel-3.0.0 in the
next message.
Any suggestions before I get the oscilloscope out?
ael
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
