Package: linux-2.6 Version: 2.6.32-38 Severity: normal
Remark: As problem seemed to be related to Bug#619371, it was first reported as info to this bug. On request of Jonathan Nieder I open a new Bug for it. After upgrading my working wake-on-lan configuration on a Dell Optiplex GX150 from lenny to squeeze, wake-on-lan does not work anymore. To get wake-on-lan to work in lenny I had to add a file /etc/modprobe.d/wol.conf with contents options 3c59x enable_wol=1 and set NETDOWN=no in /etc/default/halt (3c59X does not support ethtool, therefore the module parameter is needed) Correct function could be checked by active LEDs on ethernet-connector after power-off. After upgrade to squeeze, LEDs are off after power-off and wake-on-lan does not work. I tried several things (remove shutting down of eth0 in /etc/init.d/networking, 3c59x-module remove and load at /etc/init.d/halt, fiddling with /proc/acpi/wakeup, checking and updating /sys/bus/pci/devices/xxx/power/wakeup), but nothing helped in any way. Furtheron I installed an additional ethernet-card: 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) But all things I tried were not successful with this card, too. I now just took the source of the lenny-kernel 2.6.26, deactivated CONFIG_SYSFS_DEPRECATED in the config and built a kernel package. I then installed this kernel-package on the system without changing anything else. I then booted this kernel and wake-on-lan works again in squeeze like in lenny before (with the internal 3com-ethernet). So something is broken with wake-on-lan in 2.6.32 (maybe related to the acpi-config of the chipset?) If needed I can provide further information, perform tests or build special kernel-versions. (wake-on-lan is triggered using magic-packet from another linux system with wakeonlan and from logitech squeezeboxes) -- Package-specific info: ** Version: Linux version 2.6.32-5-686 (Debian 2.6.32-38) (b...@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Mon Oct 3 04:15:24 UTC 2011 ** Command line: BOOT_IMAGE=/boot/vmlinuz-2.6.32-5-686 root=UUID=bf8b665b-0362-4e0b-9106-d0c376484765 ro quiet ** Not tainted ** Kernel log: [ 2.296327] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd [ 2.296335] usb usb3: SerialNumber: 0000:00:1f.4 [ 2.296828] usb usb3: configuration #1 chosen from 1 choice [ 2.297042] hub 3-0:1.0: USB hub found [ 2.297077] hub 3-0:1.0: 2 ports detected [ 2.297964] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 [ 2.297973] PCI: setting IRQ 10 as level-triggered [ 2.297985] uhci_hcd 0000:01:08.0: PCI INT A -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 2.298008] uhci_hcd 0000:01:08.0: UHCI Host Controller [ 2.298038] uhci_hcd 0000:01:08.0: new USB bus registered, assigned bus number 4 [ 2.298087] uhci_hcd 0000:01:08.0: irq 10, io base 0x0000e8e0 [ 2.298215] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.298225] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.298233] usb usb4: Product: UHCI Host Controller [ 2.298240] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd [ 2.298247] usb usb4: SerialNumber: 0000:01:08.0 [ 2.298715] usb usb4: configuration #1 chosen from 1 choice [ 2.298934] hub 4-0:1.0: USB hub found [ 2.298968] hub 4-0:1.0: 2 ports detected [ 2.299144] uhci_hcd 0000:01:08.1: PCI INT B -> Link[LNKC] -> GSI 11 (level, low) -> IRQ 11 [ 2.299163] uhci_hcd 0000:01:08.1: UHCI Host Controller [ 2.299191] uhci_hcd 0000:01:08.1: new USB bus registered, assigned bus number 5 [ 2.299239] uhci_hcd 0000:01:08.1: irq 11, io base 0x0000e8c0 [ 2.299359] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 2.299368] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.299376] usb usb5: Product: UHCI Host Controller [ 2.299383] usb usb5: Manufacturer: Linux 2.6.32-5-686 uhci_hcd [ 2.299390] usb usb5: SerialNumber: 0000:01:08.1 [ 2.299803] usb usb5: configuration #1 chosen from 1 choice [ 2.300080] hub 5-0:1.0: USB hub found [ 2.300117] hub 5-0:1.0: 2 ports detected [ 2.324199] 8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004) [ 2.324298] 8139cp 0000:01:07.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip, use 8139too [ 2.368469] ata_piix 0000:00:1f.1: version 2.13 [ 2.368627] ata_piix 0000:00:1f.1: setting latency timer to 64 [ 2.371242] scsi0 : ata_piix [ 2.372921] scsi1 : ata_piix [ 2.373340] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14 [ 2.373351] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15 [ 2.381807] 8139too Fast Ethernet driver 0.9.28 [ 2.382657] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 9 [ 2.382666] PCI: setting IRQ 9 as level-triggered [ 2.382677] 8139too 0000:01:07.0: PCI INT A -> Link[LNKA] -> GSI 9 (level, low) -> IRQ 9 [ 2.385578] eth1: RealTek RTL8139 at 0xec00, 00:08:54:53:60:e9, IRQ 9 [ 2.537848] ata1.00: ATA-6: WDC WD2500JB-57GVC0, 21.02J21, max UDMA/100 [ 2.537860] ata1.00: 488397168 sectors, multi 8: LBA48 [ 2.544827] ata2.00: ATAPI: GCR-8481B, 1.06, max UDMA/33 [ 2.553683] ata1.00: configured for UDMA/100 [ 2.554024] scsi 0:0:0:0: Direct-Access ATA WDC WD2500JB-57G 21.0 PQ: 0 ANSI: 5 [ 2.560993] ata2.00: configured for UDMA/33 [ 2.574883] scsi 1:0:0:0: CD-ROM HL-DT-ST CD-ROM GCR-8481B 1.06 PQ: 0 ANSI: 5 [ 2.648165] sd 0:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB) [ 2.648373] sd 0:0:0:0: [sda] Write Protect is off [ 2.648383] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.648469] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.648957] sda:sr0: scsi3-mmc drive: 48x/48x cd/rw xa/form2 cdda tray [ 2.656027] Uniform CD-ROM driver Revision: 3.20 [ 2.657205] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.681041] sda1 sda2 sda3 < sda5 sda6 sda7 > [ 2.707178] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.765205] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.766747] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 3.281087] PM: Starting manual resume from disk [ 3.281102] PM: Resume from partition 8:5 [ 3.281107] PM: Checking hibernation image. [ 3.281466] PM: Error -22 checking image file [ 3.281472] PM: Resume from disk failed. [ 3.380216] kjournald starting. Commit interval 5 seconds [ 3.380252] EXT3-fs: mounted filesystem with ordered data mode. [ 4.770704] udev[250]: starting version 164 [ 5.440094] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 5.613857] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1 [ 5.613893] ACPI: Power Button [VBTN] [ 5.614229] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2 [ 5.614243] ACPI: Power Button [PWRF] [ 5.634595] processor LNXCPU:00: registered as cooling_device0 [ 5.674982] input: PC Speaker as /devices/platform/pcspkr/input/input3 [ 5.703062] dcdbas dcdbas: Dell Systems Management Base Driver (version 5.6.0-3.2) [ 5.768754] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 5.777693] parport_pc 00:0b: reported by Plug and Play ACPI [ 5.777805] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP] [ 5.785780] i801_smbus 0000:00:1f.3: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 5.785807] i801_smbus 0000:00:1f.3: Enabling SMBus device [ 5.820220] Intel 82802 RNG detected [ 6.450225] input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input4 [ 6.663483] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 10 (level, low) -> IRQ 10 [ 6.663527] Intel ICH 0000:00:1f.5: setting latency timer to 64 [ 7.228067] intel8x0: white list rate for 1028:00be is 44100 [ 8.191115] Adding 497972k swap on /dev/sda5. Priority:-1 extents:1 across:497972k [ 8.541902] EXT3 FS on sda1, internal journal [ 8.808689] loop: module loaded [ 9.627310] kjournald starting. Commit interval 5 seconds [ 9.627995] EXT3 FS on sda7, internal journal [ 9.628049] EXT3-fs: mounted filesystem with ordered data mode. [ 10.728059] 3c59x 0000:01:0c.0: restoring config space at offset 0xf (was 0xa0a0100, writing 0xa0a010b) [ 10.728077] 3c59x 0000:01:0c.0: restoring config space at offset 0xc (was 0x0, writing 0xfe000000) [ 10.728099] 3c59x 0000:01:0c.0: restoring config space at offset 0x3 (was 0x0, writing 0x4008) [ 10.728112] 3c59x 0000:01:0c.0: restoring config space at offset 0x1 (was 0x2100000, writing 0x2100117) [ 10.729090] eth0: setting full-duplex. [ 20.852062] eth0: no IPv6 routers present ** Model information not available ** Loaded modules: Module Size Used by loop 9769 0 snd_intel8x0 19595 0 snd_ac97_codec 79200 1 snd_intel8x0 ac97_bus 710 1 snd_ac97_codec snd_pcm 47226 2 snd_intel8x0,snd_ac97_codec snd_seq 35463 0 snd_timer 12270 2 snd_pcm,snd_seq snd_seq_device 3673 1 snd_seq snd 34423 6 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device psmouse 44809 0 soundcore 3450 1 snd intel_rng 1965 0 i2c_i801 6462 0 parport_pc 15799 0 shpchp 21220 0 dcdbas 3892 0 parport 22554 1 parport_pc pcspkr 1207 0 evdev 5609 3 serio_raw 2916 0 processor 26327 0 button 3598 0 snd_page_alloc 5045 2 snd_intel8x0,snd_pcm i2c_core 12787 1 i2c_i801 rng_core 2178 1 intel_rng pci_hotplug 18545 1 shpchp ext3 94396 2 jbd 32317 1 ext3 mbcache 3762 1 ext3 sg 19937 0 sr_mod 10770 0 sd_mod 26005 4 cdrom 26487 1 sr_mod crc_t10dif 1012 1 sd_mod ata_generic 2247 0 8139too 14949 0 ata_piix 17736 3 8139cp 13421 0 uhci_hcd 16057 0 libata 115869 2 ata_generic,ata_piix thermal 9206 0 3c59x 25036 0 ehci_hcd 28693 0 floppy 40923 0 mii 2714 3 8139too,8139cp,3c59x usbcore 98969 3 uhci_hcd,ehci_hcd nls_base 4541 1 usbcore scsi_mod 104853 4 sg,sr_mod,sd_mod,libata thermal_sys 9378 2 processor,thermal ** Network interface configuration: # This file describes the network interfaces available on your system # and how to activate them. For more information, see interfaces(5). # The loopback network interface auto lo iface lo inet loopback # The primary network interface #allow-hotplug eth0 #iface eth0 inet dhcp auto eth0 iface eth0 inet static address 192.168.0.239 netmask 255.255.255.0 network 192.168.0.0 broadcast 192.168.0.255 gateway 192.168.0.254 dns-nameservers 192.168.0.254 dns-search local.priv # post-up ethtool -s eth0 wol g # post-down ethtool -s eth0 wol g iface wlan0 inet dhcp wpa_conf /etc/wpa_supplicant.conf iface wlan1 inet dhcp wpa_conf /etc/wpa_supplicant.conf ** Network status: *** IP interfaces and addresses: 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000 link/ether 00:b0:d0:bc:10:12 brd ff:ff:ff:ff:ff:ff inet 192.168.0.239/24 brd 192.168.0.255 scope global eth0 inet6 fe80::2b0:d0ff:febc:1012/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 00:08:54:53:60:e9 brd ff:ff:ff:ff:ff:ff *** Device statistics: Inter-| Receive | Transmit face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed lo: 910 17 0 0 0 0 0 0 910 17 0 0 0 0 0 0 eth0: 2703893 2123 0 0 511 0 0 0 2334463 3909 0 0 0 1020 1530 0 eth1: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 *** Protocol statistics: Ip: 2114 total packets received 0 forwarded 0 incoming packets discarded 2114 incoming packets delivered 1838 requests sent out Icmp: 0 ICMP messages received 0 input ICMP message failed. ICMP input histogram: 0 ICMP messages sent 0 ICMP messages failed ICMP output histogram: Tcp: 32 active connections openings 16 passive connection openings 1 failed connection attempts 1 connection resets received 2 connections established 1895 segments received 1691 segments send out 0 segments retransmited 0 bad segments received. 4 resets sent Udp: 159 packets received 0 packets to unknown port received. 0 packet receive errors 147 packets sent UdpLite: TcpExt: 13 TCP sockets finished time wait in fast timer 22 delayed acks sent Quick ack mode was activated 3 times 4 packets directly queued to recvmsg prequeue. 879 packet headers predicted 155 acknowledgments not containing data payload received 826 predicted acknowledgments IpExt: InBcastPkts: 90 OutBcastPkts: 15 InOctets: 576645 OutOctets: 208929 InBcastOctets: 10903 OutBcastOctets: 660 ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub [8086:1130] (rev 02) Subsystem: Dell Device [1028:00be] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: agpgart-intel 00:02.0 VGA compatible controller [0300]: Intel Corporation 82815 Chipset Graphics Controller (CGC) [8086:1132] (rev 02) (prog-if 00 [VGA controller]) Subsystem: Dell Device [1028:00be] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 9 Region 0: Memory at f8000000 (32-bit, prefetchable) [size=64M] Region 1: Memory at ff080000 (32-bit, non-prefetchable) [size=512K] Expansion ROM at <unassigned> [disabled] Capabilities: <access denied> 00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000e000-0000efff Memory behind bridge: fd000000-feffffff Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- 00:1f.0 ISA bridge [0601]: Intel Corporation 82801BA ISA Bridge (LPC) [8086:2440] (rev 02) Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.1 IDE interface [0101]: Intel Corporation 82801BA IDE U100 Controller [8086:244b] (rev 02) (prog-if 80 [Master]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8] Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1] Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8] Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1] Region 4: I/O ports at ffa0 [size=16] Kernel driver in use: ata_piix 00:1f.2 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2442] (rev 02) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin D routed to IRQ 11 Region 4: I/O ports at ff80 [size=32] Kernel driver in use: uhci_hcd 00:1f.3 SMBus [0c05]: Intel Corporation 82801BA/BAM SMBus Controller [8086:2443] (rev 02) Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin B routed to IRQ 10 Region 4: I/O ports at dcd0 [size=16] Kernel driver in use: i801_smbus 00:1f.4 USB Controller [0c03]: Intel Corporation 82801BA/BAM USB Controller #1 [8086:2444] (rev 02) (prog-if 00 [UHCI]) Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin C routed to IRQ 5 Region 4: I/O ports at ff60 [size=32] Kernel driver in use: uhci_hcd 00:1f.5 Multimedia audio controller [0401]: Intel Corporation 82801BA/BAM AC'97 Audio Controller [8086:2445] (rev 02) Subsystem: Dell Device [1028:00be] Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin B routed to IRQ 10 Region 0: I/O ports at d800 [size=256] Region 1: I/O ports at dc40 [size=64] Kernel driver in use: Intel ICH 01:07.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10) Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (8000ns min, 16000ns max) Interrupt: pin A routed to IRQ 9 Region 0: I/O ports at ec00 [size=256] Region 1: Memory at fdfffc00 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: 8139too 01:08.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 10 Region 4: I/O ports at e8e0 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 01:08.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI]) Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin B routed to IRQ 11 Region 4: I/O ports at e8c0 [size=32] Capabilities: <access denied> Kernel driver in use: uhci_hcd 01:08.2 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 65) (prog-if 20 [EHCI]) Subsystem: VIA Technologies, Inc. USB 2.0 [1106:3104] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64, Cache Line Size: 32 bytes Interrupt: pin C routed to IRQ 11 Region 0: Memory at fdfff800 (32-bit, non-prefetchable) [size=256] Capabilities: <access denied> Kernel driver in use: ehci_hcd 01:0c.0 Ethernet controller [0200]: 3Com Corporation 3c905C-TX/TX-M [Tornado] [10b7:9200] (rev 78) Subsystem: Dell Device [1028:00be] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at e800 [size=128] Region 1: Memory at fdfff400 (32-bit, non-prefetchable) [size=128] Expansion ROM at fe000000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: 3c59x ** USB devices: Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 6.0.3 APT prefers stable APT policy: (500, 'stable') Architecture: i386 (i686) Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core) Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/bash Versions of packages linux-image-2.6.32-5-686 depends on: ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs ii linux-base 2.6.32-38 Linux image base package ii module-init-tools 3.12-1 tools for managing Linux kernel mo Versions of packages linux-image-2.6.32-5-686 recommends: ii firmware-linux-free 2.6.32-38 Binary firmware for various driver ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib Versions of packages linux-image-2.6.32-5-686 suggests: ii grub 0.97-64 GRand Unified Bootloader (dummy pa pn linux-doc-2.6.32 <none> (no description available) Versions of packages linux-image-2.6.32-5-686 is related to: pn firmware-bnx2 <none> (no description available) pn firmware-bnx2x <none> (no description available) pn firmware-ipw2x00 <none> (no description available) pn firmware-ivtv <none> (no description available) pn firmware-iwlwifi <none> (no description available) pn firmware-linux <none> (no description available) pn firmware-linux-nonfree <none> (no description available) pn firmware-qlogic <none> (no description available) pn firmware-ralink <none> (no description available) pn xen-hypervisor <none> (no description available) -- debconf information: linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686: linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686: -- To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org