Now (kernel 3.1) the cards are recognized when insterted into the
embedded reader but still seeing the weird message when booting.
This is from "dmesg":
[ 8.924189] rts_pstor: device scan complete
[ 8.924466] scsi 4:0:0:0: Direct-Access Generic- xD/SD/M.S. 1.00
PQ: 0 ANSI: 0 CCS
[ 8.924614] Bad LUN (0:1)
[ 8.924646] scsi: killing requests for dead queue
[ 8.924857] Bad target number (1:0)
[ 8.924888] scsi: killing requests for dead queue
[ 8.925094] Bad target number (2:0)
[ 8.925123] scsi: killing requests for dead queue
[ 8.925328] Bad target number (3:0)
[ 8.925358] scsi: killing requests for dead queue
[ 8.925560] Bad target number (4:0)
[ 8.925587] scsi: killing requests for dead queue
[ 8.925789] Bad target number (5:0)
[ 8.925814] scsi: killing requests for dead queue
[ 8.926016] Bad target number (6:0)
[ 8.926042] scsi: killing requests for dead queue
[ 8.926244] Bad target number (7:0)
[ 8.926270] scsi: killing requests for dead queue
[ 8.929512] sd 4:0:0:0: [sdb] Attached SCSI removable disk
[ 9.053405] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 9.054008] sd 4:0:0:0: Attached scsi generic sg1 type 0
(...)
[ 796.536030] rts_pstor 0000:01:00.1: vpd r/w failed. This is likely a
firmware bug on this device. Contact the card vendor for a firmware update.
Device information:
01:00.1 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. Device 5288
(rev 01)
Subsystem: Hewlett-Packard Company Device 148a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at 93000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq+ AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0
<512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-,
Selectable De-emphasis: -6dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance-
ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB
Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
Vector table: BAR=0 offset=00000000
PBA: BAR=0 offset=00000000
Capabilities: [d0] Vital Product Data
pcilib: sysfs_read_vpd: read failed: Connection timed out
Not readable
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF-
MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+
MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Kernel driver in use: rts_pstor
Greetings,
--
Camaleón
--
To UNSUBSCRIBE, email to debian-bugs-dist-requ...@lists.debian.org
with a subject of "unsubscribe". Trouble? Contact listmas...@lists.debian.org
