Package: linux-image-2.6.24-etchnhalf.1-amd64
Version: 2.6.24-6~etchnhalf.4
Severity: grave
Tags: patch
Justification: renders package unusable
The problem described in #476970 applies to the 2.6.24 kernel of etchnhalf, too.
It has been fixed for the 2.6.26 series, but still exists here.
To fix this issue, the kernel has to recompiled with the following settings:
CONFIG_RTC=m
CONFIG_GEN_RTC=m
# CONFIG_GEN_RTC_X is not set
If it was a mistake to report this for another package and is thus
considered a duplicate, I apologize.
Kind regards,
Patric
-- Package-specific info:
** Version:
Linux version 2.6.24-etchnhalf.1-amd64 (Debian 2.6.24-6~etchnhalf.4) ([EMAIL
PROTECTED]) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP
Mon Jul 21 10:36:02 UTC 2008
** Command line:
BOOT_IMAGE=/boot/vmlinuz-2.6.24-etchnhalf.1-amd64
root=UUID=e8c0e203-1223-44ed-93e5-fad40fed9c13 ro
** Tainted: P (1)
** Kernel log:
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c80
ACPI: Power Button (CM) [PWRB]
usb 1-10: new full speed USB device using ohci_hcd and address 5
input: PC Speaker as /class/input/input4
usb 1-10: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for Reiner SCT
Cyberjack USB card reader
cyberjack 1-7:1.0: Reiner SCT Cyberjack USB card reader converter detected
usb 1-7: Reiner SCT Cyberjack USB card reader converter now attached to ttyUSB0
usbcore: registered new interface driver cyberjack
drivers/usb/serial/cyberjack.c: v1.01 Matthias Bruestle
drivers/usb/serial/cyberjack.c: REINER SCT cyberJack pinpad/e-com USB Chipcard
Reader Driver
gameport: EMU10K1 is pci0000:01:07.1/gameport0, io 0xc400, speed 1202kHz
ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:06.1[B] -> Link [AAZA] -> GSI 20 (level, low) ->
IRQ 20
PCI: Setting latency timer of device 0000:00:06.1 to 64
usbcore: registered new interface driver hiddev
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, low) ->
IRQ 19
input: ImPS/2 Generic Wheel Mouse as /class/input/input5
pnp: the driver 'parport_pc' has been registered
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
parport_pc 00:09: driver attached
drivers/hid/usbhid/hid-core.c: timeout initializing reports
input: Logitech Inc. WingMan Extreme Digital 3D as /class/input/input6
input,hidraw0: USB HID v1.00 Joystick [Logitech Inc. WingMan Extreme Digital
3D] on usb-0000:00:02.0-9
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
usbcore: registered new interface driver snd-usb-audio
EXT3 FS on hda2, internal journal
loop: module loaded
it87: Found IT8716F chip at 0x290, revision 0
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: [EMAIL PROTECTED]
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no
debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hda9
Ending clean XFS mount for filesystem: hda9
Filesystem "dm-5": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-5
Ending clean XFS mount for filesystem: dm-5
Filesystem "dm-2": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-2
Ending clean XFS mount for filesystem: dm-2
Filesystem "dm-1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-1
Ending clean XFS mount for filesystem: dm-1
Filesystem "dm-4": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-4
Ending clean XFS mount for filesystem: dm-4
Filesystem "dm-3": Disabling barriers, not supported by the underlying device
XFS mounting filesystem dm-3
Ending clean XFS mount for filesystem: dm-3
Adding 1574328k swap on /dev/mapper/hda1_crypt. Priority:-1 extents:1
across:1574328k
PPP generic driver version 2.4.2
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
NET: Registered protocol family 24
ip_tables: (C) 2000-2006 Netfilter Core Team
powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 6000+ processors
(2 cpu cores) (version 2.20.00)
powernow-k8: 0 : fid 0x16 (3000 MHz), vid 0x8
powernow-k8: 1 : fid 0x14 (2800 MHz), vid 0xa
powernow-k8: 2 : fid 0x12 (2600 MHz), vid 0xc
powernow-k8: 3 : fid 0x10 (2400 MHz), vid 0xe
powernow-k8: 4 : fid 0xe (2200 MHz), vid 0x10
powernow-k8: 5 : fid 0xc (2000 MHz), vid 0x10
powernow-k8: 6 : fid 0xa (1800 MHz), vid 0x10
powernow-k8: 7 : fid 0x2 (1000 MHz), vid 0x12
lp0: using parport0 (interrupt-driven).
ppdev: user-space parallel port driver
Clocksource tsc unstable (delta = -219218126 ns)
eth0: no IPv6 routers present
warning: process `nvidia-installe' used the deprecated sysctl system call with
1.23.
warning: process `nvidia-installe' used the deprecated sysctl system call with
1.23.
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [APC6] enabled at IRQ 16
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC6] -> GSI 16 (level, low) ->
IRQ 16
PCI: Setting latency timer of device 0000:02:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.12 Thu Jul 17 18:10:24
PDT 2008
warning: process `nvidia-installe' used the deprecated sysctl system call with
1.23.
PCI: Setting latency timer of device 0000:02:00.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 173.14.12 Thu Jul 17 18:10:24
PDT 2008
silverback.bin[19293]: segfault at 0 rip f5bba140 rsp f5368110 error 4
usb 2-5: new high speed USB device using ehci_hcd and address 5
usb 2-5: configuration #1 chosen from 1 choice
usb 2-5: USB disconnect, address 5
pnp: the driver 'rtc_cmos' has been registered
rtc_cmos 00:05: disabling not supported
rtc_cmos: probe of 00:05 failed with error -16
pnp: the driver 'rtc_cmos' has been unregistered
pnp: the driver 'rtc_cmos' has been registered
rtc_cmos 00:05: disabling not supported
rtc_cmos: probe of 00:05 failed with error -16
pnp: the driver 'rtc_cmos' has been unregistered
** Loaded modules:
Module Size Used by
nvidia 8112656 26
binfmt_misc 17420 1
ppdev 13960 0
lp 17604 0
video 25876 0
output 8832 1 video
ac 11528 0
battery 20104 0
powernow_k8 18592 1
cpufreq_powersave 6400 1
cpufreq_ondemand 13840 0
cpufreq_conservative 13448 0
cpufreq_userspace 9860 0
cpufreq_stats 10656 0
freq_table 9728 3 powernow_k8,cpufreq_ondemand,cpufreq_stats
xt_TCPMSS 9344 1
xt_tcpmss 7040 1
xt_tcpudp 8064 1
iptable_mangle 7680 1
ip_tables 25704 1 iptable_mangle
x_tables 24968 4 xt_TCPMSS,xt_tcpmss,xt_tcpudp,ip_tables
pppoe 19456 2
pppox 8984 1 pppoe
ipv6 287016 37
ppp_generic 33824 6 pppoe,pppox
slhc 10880 1 ppp_generic
xfs 497128 6
sha256_generic 13440 0
aes_generic 31168 0
aes_x86_64 30248 12
cbc 9216 6
blkcipher 11780 1 cbc
dm_crypt 18824 1
dm_snapshot 22216 0
dm_mirror 27264 0
dm_mod 68344 15 dm_crypt,dm_snapshot,dm_mirror
it87 28688 0
hwmon_vid 7552 1 it87
eeprom 12944 0
sbp2 29196 0
loop 23044 0
joydev 17664 0
snd_emu10k1_synth 12032 0
snd_emux_synth 39680 1 snd_emu10k1_synth
snd_seq_virmidi 12032 1 snd_emux_synth
snd_seq_midi_emul 11136 1 snd_emux_synth
snd_usb_audio 96032 1
snd_usb_lib 22656 1 snd_usb_audio
snd_emu10k1 144608 6 snd_emu10k1_synth
snd_seq_dummy 8708 0
snd_seq_oss 36992 0
snd_seq_midi 13632 0
snd_seq_midi_event 12672 3 snd_seq_virmidi,snd_seq_oss,snd_seq_midi
snd_seq 59136 9
snd_emux_synth,snd_seq_virmidi,snd_seq_midi_emul,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
usbhid 35168 0
hid 42048 1 usbhid
snd_hda_intel 362408 3
snd_rawmidi 31008 4
snd_seq_virmidi,snd_usb_lib,snd_emu10k1,snd_seq_midi
firmware_class 15360 1 snd_emu10k1
snd_ac97_codec 118488 1 snd_emu10k1
snd_pcm_oss 46880 0
snd_mixer_oss 21632 1 snd_pcm_oss
ac97_bus 7168 1 snd_ac97_codec
snd_seq_device 13076 8
snd_emu10k1_synth,snd_emux_synth,snd_emu10k1,snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd_pcm 89736 6
snd_usb_audio,snd_emu10k1,snd_hda_intel,snd_ac97_codec,snd_pcm_oss
snd_util_mem 9728 2 snd_emux_synth,snd_emu10k1
snd_hwdep 14984 3 snd_emux_synth,snd_usb_audio,snd_emu10k1
snd_timer 28936 3 snd_emu10k1,snd_seq,snd_pcm
emu10k1_gp 8704 0
parport_pc 34984 1
cyberjack 15620 0
snd 66280 32
snd_emux_synth,snd_seq_virmidi,snd_usb_audio,snd_emu10k1,snd_seq_oss,snd_seq,snd_hda_intel,snd_rawmidi,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_seq_device,snd_pcm,snd_hwdep,snd_timer
parport 45068 3 ppdev,lp,parport_pc
gameport 20752 2 emu10k1_gp
soundcore 13344 1 snd
snd_page_alloc 15504 3 snd_emu10k1,snd_hda_intel,snd_pcm
pcspkr 7936 0
psmouse 46108 0
serio_raw 12036 0
i2c_nforce2 11264 0
button 14112 0
k8temp 10624 0
i2c_core 30080 3 nvidia,eeprom,i2c_nforce2
usbserial 42096 1 cyberjack
evdev 17152 3
ext3 139536 1
jbd 56232 1 ext3
mbcache 14208 1 ext3
ide_disk 21248 9
ata_generic 13188 0
libata 164016 1 ata_generic
scsi_mod 170808 2 sbp2,libata
ohci1394 37172 0
forcedeth 54668 0
ieee1394 102360 2 sbp2,ohci1394
ehci_hcd 39948 0
ohci_hcd 28292 0
amd74xx 14488 0 [permanent]
generic 9860 0 [permanent]
ide_core 145432 3 ide_disk,amd74xx,generic
thermal 22944 0
processor 45416 2 powernow_k8,thermal
fan 9992 0
** PCI devices:
00:00.0 RAM memory [0500]: nVidia Corporation MCP55 Memory Controller
[10de:0369] (rev a1)
Subsystem: Giga-byte Technology Device [1458:5001]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO-
<CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+
<CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+
600MHz+ 800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz-
600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE-
SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] #00 [fee0]
00:01.0 ISA bridge [0601]: nVidia Corporation MCP55 LPC Bridge [10de:0363] (rev
a2)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus [0c05]: nVidia Corporation MCP55 SMBus [10de:0368] (rev a2)
Subsystem: Giga-byte Technology Device [1458:0c11]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e400 [size=64]
Region 4: I/O ports at 1c00 [size=64]
Region 5: I/O ports at 1c80 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036c] (rev a1) (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at fc107000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:02.1 USB Controller [0c03]: nVidia Corporation MCP55 USB Controller
[10de:036d] (rev a2) (prog-if 20)
Subsystem: Giga-byte Technology Device [1458:5004]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at fc108000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:04.0 IDE interface [0101]: nVidia Corporation MCP55 IDE [10de:036e] (rev a1)
(prog-if 8a [Master SecP PriP])
Subsystem: Giga-byte Technology Device [1458:5002]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: AMD_IDE
Kernel modules: ata_generic, generic, amd74xx
00:06.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI bridge [10de:0370] (rev
a2) (prog-if 01)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fc000000-fc0fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn+
Capabilities: [b8] Subsystem: nVidia Corporation Device [10de:cb84]
Capabilities: [8c] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
00:06.1 Audio device [0403]: nVidia Corporation MCP55 High Definition Audio
[10de:0371] (rev a2)
Subsystem: Giga-byte Technology Device [1458:a002]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at fc100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: HDA Intel
Kernel modules: snd-hda-intel
00:08.0 Bridge [0680]: nVidia Corporation MCP55 Ethernet [10de:0373] (rev a2)
Subsystem: Giga-byte Technology Device [1458:e000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 1278
Region 0: Memory at fc104000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e800 [size=8]
Region 2: Memory at fc105000 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at fc106000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [70] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=2 offset=00000000
PBA: BAR=3 offset=00000000
Capabilities: [50] Message Signalled Interrupts: Mask+ 64bit+ Queue=0/3
Enable+
Address: 00000000fee0300c Data: 4181
Masking: 000000fe Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping Enable- Fixed+
Kernel driver in use: forcedeth
Kernel modules: forcedeth
00:0f.0 PCI bridge [0604]: nVidia Corporation MCP55 PCI Express bridge
[10de:0377] (rev a2)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f8000000-fbffffff
Prefetchable memory behind bridge: 00000000e0000000-00000000efffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: nVidia Corporation Device [10de:0000]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1
Enable+
Address: 00000000fee0300c Data: 4149
Capabilities: [60] HyperTransport: MSI Mapping Enable- Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <4us
ExtTag- RBE+ FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+
Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug-
Surpise-
Slot # 0, PowerLimit 0.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+
Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna-
CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
Kernel driver in use: k8temp
Kernel modules: k8temp
01:07.0 Multimedia audio controller [0401]: Creative Labs SB Live! EMU10k1
[1102:0002] (rev 07)
Subsystem: Creative Labs Device [1102:8022]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 5000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at c000 [size=32]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: EMU10K1_Audigy
Kernel modules: snd-emu10k1
01:07.1 Input device controller [0980]: Creative Labs SB Live! Game Port
[1102:7002] (rev 07)
Subsystem: Creative Labs Device [1102:0020]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: I/O ports at c400 [size=8]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Emu10k1_gameport
Kernel modules: emu10k1-gp
01:0a.0 FireWire (IEEE 1394) [0c00]: Texas Instruments TSB43AB23
IEEE-1394a-2000 Controller (PHY/Link) [104c:8024] (prog-if 10)
Subsystem: Giga-byte Technology Device [1458:1000]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at fc004000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at fc000000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ohci1394
Kernel modules: ohci1394
02:00.0 VGA compatible controller [0300]: nVidia Corporation Geforce 9600 GT
512mb [10de:0622] (rev a1)
Subsystem: eVga.com. Corp. Device [3842:c865]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at d000 [size=128]
[virtual] Expansion ROM at fb000000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns,
L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal-
Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr-
TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency
L0 <512ns, L1 <1us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+
DLActive- BWMgmt- ABWMgmt-
Capabilities: [b4] Vendor Specific Information <?>
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
Capabilities: [600] Vendor Specific Information <?>
Kernel driver in use: nvidia
Kernel modules: nvidiafb, nvidia
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (900, 'testing'), (400, 'stable'), (300, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.24-etchnhalf.1-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.24-etchnhalf.1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.22 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92e tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.24-etchnhalf.1-amd64 recommends no packages.
Versions of packages linux-image-2.6.24-etchnhalf.1-amd64 suggests:
ii grub-pc [grub] 1.96+20080724-2 GRand Unified Bootloader, version
pn linux-doc-2.6.24 <none> (no description available)
-- debconf information:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/depmod-error-initrd-2.6.24-etchnhalf.1-amd64:
false
linux-image-2.6.24-etchnhalf.1-amd64/postinst/kimage-is-a-directory:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.24-etchnhalf.1-amd64/postinst/old-dir-initrd-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.24-etchnhalf.1-amd64/preinst/abort-overwrite-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/preinst/overwriting-modules-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/bootloader-initrd-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/lilo-initrd-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/failed-to-move-modules-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/bootloader-test-error-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/create-kimage-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/postinst/depmod-error-2.6.24-etchnhalf.1-amd64:
false
linux-image-2.6.24-etchnhalf.1-amd64/preinst/abort-install-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/old-initrd-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/preinst/initrd-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/preinst/elilo-initrd-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/postinst/bootloader-error-2.6.24-etchnhalf.1-amd64:
linux-image-2.6.24-etchnhalf.1-amd64/postinst/old-system-map-link-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/prerm/removing-running-kernel-2.6.24-etchnhalf.1-amd64:
true
linux-image-2.6.24-etchnhalf.1-amd64/prerm/would-invalidate-boot-loader-2.6.24-etchnhalf.1-amd64:
true
--
To UNSUBSCRIBE, email to [EMAIL PROTECTED]
with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]
