On Feb 14, Mike Crowe <[EMAIL PROTECTED]> wrote: >> I don't think this issue is limited to network devices.
On Tue, Feb 14, 2006 at 01:46:30PM +0100, Marco d'Itri wrote: > You are showing some totally unrelated issue which is obviously a > bug in lvm2. I admit that the log excerpt I provided was rather confusing and did not contain the pertinent information. The issue I was aiming to describe is unrelated to LVM as far as I can determine. That vgchange not found error occurs in both successful and unsuccessful boots. I've attached two separate logs - one from a successful boot and one from a failed boot. It hope it is clear that these two logs show sata, megaraid, aic79xx and USB modules scanning for devices in a different order. This means that on some boots the boot disk on megaraid is sda and on others it's sdb. I see no reason why this randomness could not also occur between SATA, and on/off board SCSI devices but don't have the hardware available to prove this at the moment. -- Mike Crowe
LILO 22.6.1 Loading Linux....................................................................................................................................... BIOS data check successful Bootdata ok (command line is auto BOOT_IMAGE=Linux ro root=801 console=tty0 console=ttyS0,9600n8) Linux version 2.6.15-1-amd64-k8-smp (Debian 2.6.15-2bpo1) ([EMAIL PROTECTED]) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 SMP Thu Jan 26 00:57:18 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000fbff0000 (usable) BIOS-e820: 00000000fbff0000 - 00000000fbfff000 (ACPI data) BIOS-e820: 00000000fbfff000 - 00000000fc000000 (ACPI NVS) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000200000000 (usable) SRAT: PXM 0 -> APIC 0 -> Node 0 SRAT: PXM 0 -> APIC 1 -> Node 0 SRAT: PXM 1 -> APIC 2 -> Node 1 SRAT: PXM 1 -> APIC 3 -> Node 1 SRAT: Node 0 PXM 0 100000-fc000000 SRAT: Node 1 PXM 1 100000000-200000000 SRAT: Node 0 PXM 0 100000-100000000 SRAT: Node 0 PXM 0 0-100000000 Bootmem setup node 0 0000000000000000-0000000100000000 Bootmem setup node 1 0000000100000000-0000000200000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) Processor #2 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) Processor #3 15:1 APIC version 16 ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x05] address[0xfebff000] gsi_base[24]) IOAPIC[1]: apic_id 5, version 17, address 0xfebff000, GSI 24-27 ACPI: IOAPIC (id[0x06] address[0xfebfe000] gsi_base[28]) IOAPIC[2]: apic_id 6, version 17, address 0xfebfe000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at fc400000 (gap: fc000000:3780000) Checking aperture... CPU 0: aperture @ 8000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Your BIOS doesn't leave a aperture memory hole Please enable the IOMMU option in the BIOS setup This costs you 64 MB of RAM Mapping aperture over 65536 KB of RAM @ 8000000 Built 2 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=801 console=tty0 console=ttyS0,9600n8 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 2191.499 MHz processor. Console: colour VGA+ 80x50 Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) Memory: 8120696k/8388608k available (1861k kernel code, 201924k reserved, 870k data, 208k init) Calibrating delay using timer specific routine.. 4389.36 BogoMIPS (lpj=2194681) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(2) -> Node 0 -> Core 0 mtrr: v2.0 (20020519) Using local APIC timer interrupts. Detected 12.451 MHz APIC timer. Booting processor 1/4 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4387.71 BogoMIPS (lpj=2193855) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1(2) -> Node 0 -> Core 1 Dual Core AMD Opteron(tm) Processor 275 stepping 02 CPU 1: Syncing TSC to CPU 0. CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 638 cycles) Booting processor 2/4 APIC 0x2 Initializing CPU#2 Calibrating delay using timer specific routine.. 4382.29 BogoMIPS (lpj=2191145) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 2(2) -> Node 1 -> Core 0 Dual Core AMD Opteron(tm) Processor 275 stepping 02 CPU 2: Syncing TSC to CPU 0. CPU 2: synchronized TSC with CPU 0 (last diff -3 cycles, maxerr 874 cycles) Booting processor 3/4 APIC 0x3 Initializing CPU#3 Calibrating delay using timer specific routine.. 4382.29 BogoMIPS (lpj=2191145) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 3(2) -> Node 1 -> Core 1 Dual Core AMD Opteron(tm) Processor 275 stepping 02 CPU 3: Syncing TSC to CPU 0. CPU 3: synchronized TSC with CPU 0 (last diff 9 cycles, maxerr 850 cycles) Brought up 4 CPUs Disabling vsyscall due to use of PM timer time.c: Using PM based timekeeping. testing NMI watchdog ... OK. checking if image is initramfs... it is NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report TC classifier action (bugs to netdev@vger.kernel.org cc [EMAIL PROTECTED]) PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ 8000000 size 65536 KB PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture pnp: 00:08: ioport range 0x680-0x6ff has been reserved pnp: 00:08: ioport range 0x295-0x296 has been reserved PCI: Bridge: 0000:00:06.0 IO window: 9000-bfff MEM window: fc900000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: 7000-8fff MEM window: fc600000-fc8fffff PREFETCH window: ff500000-ff5fffff PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1139949243.500:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: MSI quirk detected. pci_msi_quirk set. PCI: MSI quirk detected. pci_msi_quirk set. Real Time Clock Driver v1.12 hpet_acpi_add: no address or irqs in _CRS Linux agpgart interface v0.101 (c) Dave Jones PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize usbmon: debugfs is not available mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) input: AT Translated Set 2 keyboard as /class/input/input0 TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Freeing unused kernel memory: 208k freed Loading, please wait... Begin: Loading modules ... DoneACPI: Processor [CPU1] (supports. Begin: Runnin 8 throttling statesg /scripts/init-) premount ... Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005) SCSI subsystem initialized GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 16 ohci_hcd 0000:03:00.0: OHCI Host Controller ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:03:00.0: irq 16, io mem 0xfeafc000 megaraid: 2.20.4.6 (Release Date: Mon Mar 07 12:27:22 EST 2005) hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected AMD8111: IDE controller at PCI slot 0000:00:07.1 AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio ACPI: PCI Interrupt 0000:03:00.1[D] -> GSI 19 (level, low) -> IRQ 16 ohci_hcd 0000:03:00.1: OHCI Host Controller ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:03:00.1: irq 16, io mem 0xfeafd000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usb 1-2: new full speed USB device using ohci_hcd and address 2 tg3.c:v3.47 (Dec 28, 2005) megaraid: probe new device 0x1000:0x1960:0x1000:0x0520: bus 2:slot 3:func 0 GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 27 (level, low) -> IRQ 17 GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:02:09.0[A] -> GSI 24 (level, low) -> IRQ 18 eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:17:3a eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[763f0000] GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:02:09.1[B] -> GSI 25 (level, low) -> IRQ 19 eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:17:3b eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth1: dma_rwctrl[763f0000] Initializing USB Mass Storage driver... megaraid: fw version:[1L37] bios version:[G119] scsi0 : LSI Logic MegaRAID driver scsi[0]: scanning scsi channel 0 [Phy 0] for non-raid devices scsi1 : SCSI emulation for USB Mass Storage devices usbcore: registered new driver usb-storage USB Mass Storage support registered. hda: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 19 (level, low) -> IRQ 16 ata1: SATA max UDMA/100 cmd 0xFFFFC2000001EC80 ctl 0xFFFFC2000001EC8A bmdma 0xFFFFC2000001EC00 irq 16 ata2: SATA max UDMA/100 cmd 0xFFFFC2000001ECC0 ctl 0xFFFFC2000001ECCA bmdma 0xFFFFC2000001EC08 irq 16 ata3: SATA max UDMA/100 cmd 0xFFFFC2000001EE80 ctl 0xFFFFC2000001EE8A bmdma 0xFFFFC2000001EE00 irq 16 ata4: SATA max UDMA/100 cmd 0xFFFFC2000001EEC0 ctl 0xFFFFC2000001EECA bmdma 0xFFFFC2000001EE08 irq 16 ata1: no device found (phy stat 00000000) scsi2 : sata_sil ata2: no device found (phy stat 00000000) scsi3 : sata_sil scsi[0]: scanning scsi channel 1 [virtual] for logical drives Vendor: MegaRAID Model: LD0 RAID5 79424R Rev: 1L37 Type: Direct-Access <6>ata3: no device found (phy stat 00000000) scsi4 : sata_sil ANSI SCSI revision: 02 SCSI device sda: 572260352 512-byte hdwr sectors (292997 MB) ata4: no device found (phy stat 00000000) scsi5 : sata_sil ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 24 (level, low) -> IRQ 18 sda: asking for cache data failed sda: assuming drive cache: write through SCSI device sda: 572260352 512-byte hdwr sectors (292997 MB) scsi6 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11 <Adaptec AIC7902 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs sda: asking for cache data failed sda: assuming drive cache: write through sda: sda1 sda2 sda3 sd 0:1:0:0: Attached scsi disk sda Vendor: Generic Model: USB CF Reader Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sdb: 250880 512-byte hdwr sectors (128 MB) sdb: Write Protect is off sdb: assuming drive cache: write through SCSI device sdb: 250880 512-byte hdwr sectors (128 MB) sdb: Write Protect is off sdb: assuming drive cache: write through sdb: sdb1 sd 1:0:0:0: Attached scsi removable disk sdb ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 25 (level, low) -> IRQ 19 scsi7 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11 <Adaptec AIC7902 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Done. Begin: Mounting root file system ... Begin: Running /scripts/loSGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled cal-top ... /scSGI XFS Quota Management subsystem ripts/local-top/XFS mounting filesystem sda1 lvm: 36: vgchange: not found Done. Begin: Running /scripts/local-premount ... Done. Begin: Running /scripts/log-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... Done. INIT: version 2.86 booting Starting the hotplug events dispatcher: udevd. Synthesizing the initial hotplug events...hw_random: AMD768 system management I/O registers at 0x1000. hw_random hardware driver 1.0.0 loaded input: PC Speaker as /class/input/input1 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 shpchp: HPC vendor_id 1022 device_id 7460 ss_vid 0 ss_did 0 shpchp: shpc_init: cannot reserve MMIO region shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0 shpchp: shpc_init: cannot reserve MMIO region shpchp: HPC vendor_id 1022 device_id 7450 ss_vid 0 ss_did 0 shpchp: shpc_init: cannot reserve MMIO region done. Waiting for /dev to be fully populated...shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 done. Activating swap.Adding 24402724k swap on /dev/sda3. Priority:-1 extents:1 across:24402724k Checking root file system... fsck 1.37 (21-Mar-2005) System time was Tue Feb 14 20:34:48 UTC 2006. Setting the System Clock using the Hardware Clock as reference... System Clock set. System local time is now Tue Feb 14 20:34:50 UTC 2006. Cleaning up ifupdown...done. Calculating module dependencies...done. Loading modules... ide-cd ide-disk ide-generic psmouse device-mapper: 4.4.0-ioctl (2005-01-12) initialised: [EMAIL PROTECTED] sd_mod All modules loaded. Creating device-mapper devices...done. Checking alXFS mounting filesystem sda2 l file systems... fsck 1.37 (21-Mar-2005) Setting kernel variables ... ... done. Mounting local filesystems... /dev/sda2 on /home type xfs (rw) Cleaning /tmp /var/run /var/lock. Detecting hardware: tg3 sata_sil megaraid aic79xx usb_ohci Skipping already loaded module tg3. Skipping already loaded module sata_sil. Loading megaraid module. Skipping already loaded module aic79xx. Skipping already loaded module ohci_hcd. Setting sensors limits: done. Running 0dns-down to make sure resolv.conf is ok...done. Setting up networking...done. Setting up IP spoofing protection: rp_filter. Configuring network interfaces...done. Starting portmap daemon: portmap. Setting the System Clock using the Hardware Clock as reference... System Clock set. Local time: Tue Feb 14 20:34:54 GMT 2006 Running ntpdate to synchronize clocktg3: eth0: Link is up at 1000 Mbps, full duplex. tg3: eth0: Flow control is on for TX and on for RX. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver . Initializing random number generator...done. Recovering nvi editor sessions... done. SettingINIT: Entering runlevel: 2 Starting system log daemon: syslogd. Starting kernel log daemon: klogd. Starting portmap daemon: portmap. Starting automounter: loading autofs4 kernel module, done. Starting system message bus: dbus-1. Starting DirMngr: dirmngr. Starting MTA: exim4. Starting internet superserver: inetd. Starting printer spooler: lpd . Exporting directories for NFS kernel daemon...Installing knfsd (copyright (C) 1996 [EMAIL PROTECTED]). done. Starting NFS kerNFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory nel daemon: nfsdNFSD: recovery directory /var/lib/nfs/v4recovery doesn't exist NFSD: starting 90-second grace period mountd. Starting Samba daemons: nmbd smbd. Starting OpenBSD Secure Shell server: sshd. Starting file alteration monitor: FAM. Starting NFS common utilities: statd. Starting external OpenBSD Secure Shell server: sshd_external/etc/ssh/sshd_external_config line 35: Deprecated option RhostsAuthentication /etc/ssh/sshd_external_config line 56: Deprecated option PAMAuthenticationViaKbdInt Could not load host key: /etc/ssh/ssh_host_key Disabling protocol version 1. Could not load host key . Starting NTP server: ntpd. ProFTPd is started from inetd/xinetd. Starting deferred execution scheduler: atd. Starting periodic command scheduler: cron. Starting web server: Apache2. Starting Distributed C compiler: distccd. Debian GNU/Linux 3.1 pulp ttyS0 pulp login:
LILO 22.6.1 Loading Linux....................................................................................................................................... BIOS data check successful Bootdata ok (command line is auto BOOT_IMAGE=Linux ro root=801 console=tty0 console=ttyS0,9600n8) Linux version 2.6.15-1-amd64-k8-smp (Debian 2.6.15-2bpo1) ([EMAIL PROTECTED]) (gcc version 3.3.5 (Debian 1:3.3.5-13)) #1 SMP Thu Jan 26 00:57:18 UTC 2006 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000fbff0000 (usable) BIOS-e820: 00000000fbff0000 - 00000000fbfff000 (ACPI data) BIOS-e820: 00000000fbfff000 - 00000000fc000000 (ACPI NVS) BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000200000000 (usable) SRAT: PXM 0 -> APIC 0 -> Node 0 SRAT: PXM 0 -> APIC 1 -> Node 0 SRAT: PXM 1 -> APIC 2 -> Node 1 SRAT: PXM 1 -> APIC 3 -> Node 1 SRAT: Node 0 PXM 0 100000-fc000000 SRAT: Node 1 PXM 1 100000000-200000000 SRAT: Node 0 PXM 0 100000-100000000 SRAT: Node 0 PXM 0 0-100000000 Bootmem setup node 0 0000000000000000-0000000100000000 Bootmem setup node 1 0000000100000000-0000000200000000 ACPI: PM-Timer IO Port: 0x1008 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) Processor #2 15:1 APIC version 16 ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) Processor #3 15:1 APIC version 16 ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 17, address 0xfec00000, GSI 0-23 ACPI: IOAPIC (id[0x05] address[0xfebff000] gsi_base[24]) IOAPIC[1]: apic_id 5, version 17, address 0xfebff000, GSI 24-27 ACPI: IOAPIC (id[0x06] address[0xfebfe000] gsi_base[28]) IOAPIC[2]: apic_id 6, version 17, address 0xfebfe000, GSI 28-31 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Setting APIC routing to flat Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at fc400000 (gap: fc000000:3780000) Checking aperture... CPU 0: aperture @ 8000000 size 32 MB Aperture from northbridge cpu 0 too small (32 MB) No AGP bridge found Your BIOS doesn't leave a aperture memory hole Please enable the IOMMU option in the BIOS setup This costs you 64 MB of RAM Mapping aperture over 65536 KB of RAM @ 8000000 Built 2 zonelists Kernel command line: auto BOOT_IMAGE=Linux ro root=801 console=tty0 console=ttyS0,9600n8 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 3.579545 MHz PM timer. time.c: Detected 2191.728 MHz processor. Console: colour VGA+ 80x50 Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes) Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes) Memory: 8120696k/8388608k available (1861k kernel code, 201924k reserved, 870k data, 208k init) Calibrating delay using timer specific routine.. 4389.86 BogoMIPS (lpj=2194930) Security Framework v1.0.0 initialized SELinux: Disabled at boot. Capability LSM initialized Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 0(2) -> Node 0 -> Core 0 mtrr: v2.0 (20020519) Using local APIC timer interrupts. Detected 12.453 MHz APIC timer. Booting processor 1/4 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 4382.91 BogoMIPS (lpj=2191457) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 1(2) -> Node 0 -> Core 1 Dual Core AMD Opteron(tm) Processor 275 stepping 02 CPU 1: Syncing TSC to CPU 0. CPU 1: synchronized TSC with CPU 0 (last diff 0 cycles, maxerr 638 cycles) Booting processor 2/4 APIC 0x2 Initializing CPU#2 Calibrating delay using timer specific routine.. 4382.99 BogoMIPS (lpj=2191495) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 2(2) -> Node 1 -> Core 0 Dual Core AMD Opteron(tm) Processor 275 stepping 02 CPU 2: Syncing TSC to CPU 0. CPU 2: synchronized TSC with CPU 0 (last diff 8 cycles, maxerr 850 cycles) Booting processor 3/4 APIC 0x3 Initializing CPU#3 Calibrating delay using timer specific routine.. 4382.68 BogoMIPS (lpj=2191340) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 1024K (64 bytes/line) CPU 3(2) -> Node 1 -> Core 1 Dual Core AMD Opteron(tm) Processor 275 stepping 02 CPU 3: Syncing TSC to CPU 0. CPU 3: synchronized TSC with CPU 0 (last diff -2 cycles, maxerr 850 cycles) Brought up 4 CPUs Disabling vsyscall due to use of PM timer time.c: Using PM based timekeeping. testing NMI watchdog ... OK. checking if image is initramfs... it is NET: Registered protocol family 16 ACPI: bus type pci registered PCI: Using configuration type 1 ACPI: Subsystem revision 20050902 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (0000:00) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 13 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report TC classifier action (bugs to netdev@vger.kernel.org cc [EMAIL PROTECTED]) PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ 8000000 size 65536 KB PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture pnp: 00:08: ioport range 0x680-0x6ff has been reserved pnp: 00:08: ioport range 0x295-0x296 has been reserved PCI: Bridge: 0000:00:06.0 IO window: 9000-bfff MEM window: fc900000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:0a.0 IO window: 7000-8fff MEM window: fc600000-fc8fffff PREFETCH window: ff500000-ff5fffff PCI: Bridge: 0000:00:0b.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ audit: initializing netlink socket (disabled) audit(1139949005.075:1): initialized VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered PCI: MSI quirk detected. pci_msi_quirk set. PCI: MSI quirk detected. pci_msi_quirk set. Real Time Clock Driver v1.12 hpet_acpi_add: no address or irqs in _CRS Linux agpgart interface v0.101 (c) Dave Jones PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A serial8250: ttyS0 at I/O 0x3f8 (irq = 0) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 0) is a 16550A 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize usbmon: debugfs is not available mice: PS/2 mouse device common for all mice NET: Registered protocol family 2 IP route cache hash table entries: 262144 (order: 9, 2097152 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) input: AT Translated Set 2 keyboard as /class/input/input0 TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Freeing unused kernel memory: 208k freed Loading, please wait... Begin: Loading modules ... DoneACPI: Processor [CPU1] (supports. Begin: Runnin<7>Losing some ticks... checking if CPU frequency changed. g /scripts/init- 8 throttling statespremount ... ) Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST 2005) SCSI subsystem initialized GSI 16 sharing vector 0xA9 and IRQ 16 ACPI: PCI Interrupt 0000:03:00.0[D] -> GSI 19 (level, low) -> IRQ 16 ohci_hcd 0000:03:00.0: OHCI Host Controller ohci_hcd 0000:03:00.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:03:00.0: irq 16, io mem 0xfeafc000 AMD8111: IDE controller at PCI slot 0000:00:07.1 hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected AMD8111: chipset revision 3 AMD8111: not 100% native mode: will probe irqs later AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio ACPI: PCI Interrupt 0000:03:00.1[D] -> GSI 19 (level, low) -> IRQ 16 ohci_hcd 0000:03:00.1: OHCI Host Controller ohci_hcd 0000:03:00.1: new USB bus registered, assigned bus number 2 ohci_hcd 0000:03:00.1: irq 16, io mem 0xfeafd000 megaraid: 2.20.4.6 (Release Date: Mon Mar 07 12:27:22 EST 2005) hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected tg3.c:v3.47 (Dec 28, 2005) GSI 17 sharing vector 0xB1 and IRQ 17 ACPI: PCI Interrupt 0000:02:09.0[A] -> <6>usb 1-2: new full speed USB device using ohci_hcd and address 2 GSI 24 (level, low) -> IRQ 17 eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:17:3a eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth0: dma_rwctrl[763f0000] GSI 18 sharing vector 0xB9 and IRQ 18 ACPI: PCI Interrupt 0000:02:09.1[B] -> GSI 25 (level, low) -> IRQ 18 eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:66MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:30:17:3b eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] eth1: dma_rwctrl[763f0000] Initializing USB Mass Storage driver... scsi0 : SCSI emulation for USB Mass Storage devices hda: _NEC DVD_RW ND-3550A, ATAPI CD/DVD-ROM drive usbcore: registered new driver usb-storage USB Mass Storage support registered. ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ACPI: PCI Interrupt 0000:03:05.0[A] -> GSI 19 (level, low) -> IRQ 16 ata1: SATA max UDMA/100 cmd 0xFFFFC2000001CC80 ctl 0xFFFFC2000001CC8A bmdma 0xFFFFC2000001CC00 irq 16 ata2: SATA max UDMA/100 cmd 0xFFFFC2000001CCC0 ctl 0xFFFFC2000001CCCA bmdma 0xFFFFC2000001CC08 irq 16 ata3: SATA max UDMA/100 cmd 0xFFFFC2000001CE80 ctl 0xFFFFC2000001CE8A bmdma 0xFFFFC2000001CE00 irq 16 ata4: SATA max UDMA/100 cmd 0xFFFFC2000001CEC0 ctl 0xFFFFC2000001CECA bmdma 0xFFFFC2000001CE08 irq 16 ata1: no device found (phy stat 00000000) scsi1 : sata_sil ata2: no device found (phy stat 00000000) scsi2 : sata_sil ata3: no device found (phy stat 00000000) scsi3 : sata_sil ata4: no device found (phy stat 00000000) scsi4 : sata_sil megaraid: probe new device 0x1000:0x1960:0x1000:0x0520: bus 2:slot 3:func 0 ACPI: PCI Interrupt 0000:02:06.0[A] -> GSI 24 (level, low) -> IRQ 17 GSI 19 sharing vector 0xC1 and IRQ 19 ACPI: PCI Interrupt 0000:02:03.0[A] -> GSI 27 (level, low) -> IRQ 19 scsi5 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11 <Adaptec AIC7902 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs megaraid: fw version:[1L37] bios version:[G119] scsi6 : LSI Logic MegaRAID driver scsi[6]: scanning scsi channel 0 [Phy 0] for non-raid devices Vendor: Generic Model: USB CF Reader Rev: 2.00 Type: Direct-Access ANSI SCSI revision: 00 SCSI device sda: 250880 512-byte hdwr sectors (128 MB) sda: Write Protect is off sda: assuming drive cache: write through SCSI device sda: 250880 512-byte hdwr sectors (128 MB) sda: Write Protect is off sda: assuming drive cache: write through sda: sda1 sd 0:0:0:0: Attached scsi removable disk sda scsi[6]: scanning scsi channel 1 [virtual] for logical drives Vendor: MegaRAID Model: LD0 RAID5 79424R Rev: 1L37 Type: Direct-Access ANSI SCSI revision: 02 SCSI device sdb: 572260352 512-byte hdwr sectors (292997 MB) sdb: asking for cache data failed sdb: assuming drive cache: write through SCSI device sdb: 572260352 512-byte hdwr sectors (292997 MB) sdb: asking for cache data failed sdb: assuming drive cache: write through sdb: sdb1 sdb2 sdb3 sd 6:1:0:0: Attached scsi disk sdb ACPI: PCI Interrupt 0000:02:06.1[B] -> GSI 25 (level, low) -> IRQ 18 scsi7 : Adaptec AIC79XX PCI-X SCSI HBA DRIVER, Rev 1.3.11 <Adaptec AIC7902 Ultra320 SCSI adapter> aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI 33 or 66Mhz, 512 SCBs hda: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 Done. Begin: Mounting root file system ... Begin: Running /scripts/local-top ... /scripts/local-top/lvm: 36: vgchange: not found Done. Begin: Running /scripts/local-premount ... Done. FATAL: Module unknown not found. mount: Mounting /dev/root on /root failed: No such device Begin: Running /scripts/log-bottom ... Done. Done. Begin: Running /scripts/init-bottom ... mount: Mounting /root/dev on /dev/.static/dev failed: No such file or directory Done. mount: Mounting /sys on /root/sys failed: No such file or directory mount: Mounting /proc on /root/proc failed: No such file or directory Target filesystem doesn't have /sbin/init BusyBox v1.00-pre10 (Debian 20040623-1) Built-in shell (ash) Enter 'help' for a list of built-in commands. /bin/sh: can't access tty; job control turned off / #