Le 09/02/2017 à 23:20, Andrew Shadura a écrit :
> Hi,
>
> On 9 February 2017 at 21:10, Vincent Danjean <vdanj...@debian.org> wrote:
>> Package: hostapd
>> Version: 1:2.5-2+v2.4-3+b1
>> Severity: grave
>> Justification: renders package unusable
>>
>> Hi,
>>
>> I just upgraded a machine from jessie to stretch. With the stretch
>> version of hostapd, the deamon does not start:
>> # hostapd /etc/hostapd/hostapd.conf
>> Configuration file: /etc/hostapd/hostapd.conf
>> Using interface wlan0 with hwaddr f4:ec:38:c5:fd:94 and ssid "dino-wpa1"
>> Failed to set beacon parameters
>> Interface initialization failed
>> wlan0: interface state UNINITIALIZED->DISABLED
>> wlan0: AP-DISABLED
>> wlan0: Unable to setup interface.
>> wlan0: interface state DISABLED->DISABLED
>> wlan0: AP-DISABLED
>> hostapd_free_hapd_data: Interface wlan0_2 wasn't started
>> wlan0: AP-DISABLED
>> hostapd_free_hapd_data: Interface wlan0_1 wasn't started
>> wlan0: AP-DISABLED
>> hostapd_free_hapd_data: Interface wlan0 wasn't started
>> nl80211: deinit ifname=wlan0 disabled_11b_rates=0
>> #
>>
>> If I downgrade the hostapd package to the jessie version
>> (1:2.3-1+deb8u4), then it works perfectly:
>> # apt-get install --reinstall hostapd/jessie
>> [...]
>> Les paquets suivants seront mis à une VERSION INFÉRIEURE :
>> hostapd
>> 0 mis à jour, 0 nouvellement installés, 1 remis à une version inférieure, 0
>> à enlever et 44 non mis à jour.
>> [...]
>> Préparation du dépaquetage de .../hostapd_1%3a2.3-1+deb8u4_amd64.deb ...
>> Dépaquetage de hostapd (1:2.3-1+deb8u4) sur (1:2.5-2+v2.4-3+b1) ...
>> Paramétrage de hostapd (1:2.3-1+deb8u4) ...
>> [...]
>> # hostapd /etc/hostapd/hostapd.conf
>> Configuration file: /etc/hostapd/hostapd.conf
>> Using interface wlan0 with hwaddr f4:ec:38:c5:fd:94 and ssid "dino-wpa1"
>> Using interface wlan0_1 with hwaddr f4:ec:38:c5:fd:95 and ssid "dino"
>> Using interface wlan0_2 with hwaddr f4:ec:38:c5:fd:96 and ssid
>> "dino-guess"
>> wlan0: interface state UNINITIALIZED->ENABLED
>> wlan0: AP-ENABLED
>> [.. and then authentifications from client...]
>>
>> So, it seems there is a major regression in the hostapd package.
>> Feel free to ask more information if required.
>
> I'm going to ask you to tell me what hardware you use.
>From lspci:
04:00.0 Network controller: Qualcomm Atheros AR9285 Wireless Network Adapter
(PCI-Express) (rev 01)
If you need more information, just tell me where to look at.
> Also, please try
> and get more logs please, especially those wpa_supplicant produces with
> -dt (you can add it with a systemd override file).
I do not use wpa_supplicant. I only run hostapd. I use this computer
(and this wireless card) as an AP at home.
You can find in attachment the output of
# hostapd -dd /etc/hostapd/hostapd.conf
- for the testing version
- for the stable version
- for the unstable version
>> Note that the unstable version works. So I will mark this bug as fixed
>> for the 1:2.6-3 version as soon as I get its number
>
> That's pretty much a bad news, as 2.6 breaks networking for lot more
> people, it seems.
>
> There's a thread about a related issue:
> http://lists.infradead.org/pipermail/hostap/2017-January/037042.html
>
> Please have a look and let me know whether what you're observing is the
> same bug or not, and whether the patch works.
I'm not using wpa_supplicant, so it does not seem the same bug.
Moreover, the proposed patch in
http://lists.infradead.org/pipermail/hostap/2017-January/037060.html
do not apply at all for the testing sources.
In the testing sources, in the wpa_driver_nl80211_set_ap function,
the "if (beacon_set)" test do not have any "else" clause to patch.
Regards,
Vincent
>
> Thanks!
>
--
Vincent Danjean GPG key ID 0xD17897FA vdanj...@debian.org
GPG key fingerprint: 621E 3509 654D D77C 43F5 CA4A F6AE F2AF D178 97FA
Unofficial pkgs: http://moais.imag.fr/membres/vincent.danjean/deb.html
APT repo: deb http://people.debian.org/~vdanjean/debian unstable main
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=2 op=0 soft=0 hard=0
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supported cipher 00-0f-ac:13
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Using driver-based off-channel TX
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Setup AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x55a115563330
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x55a115563330
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x55a115563330 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x55a115563330 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x55a115563330 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x55a115563330 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x55a115563330 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x55a115563330 match=
nl80211: Add own interface ifindex 23
nl80211: if_indices[16]: 23
nl80211: Add own interface ifindex 4
nl80211: if_indices[16]: 23 4
nl80211: Adding interface wlan0 into bridge br-wifi
phy: phy0
BSS count 3, BSSID mask ff:ff:ff:ff:ff:fc (2 bits)
nl80211: Regulatory information - country=98
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 25 MHz 20 mBm (no IR)
nl80211: 2474-2482 @ 8 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-59400 @ 2160 MHz 0 mBm
nl80211: 59400-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=13 freq=2472 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=13 freq=2472 MHz max_tx_power=20 dBm
Completing interface initialization
Mode: IEEE 802.11g Channel: 5 Frequency: 2432 MHz
DFS 0 channels required radar detection
nl80211: Set freq 2432 (ht_enabled=0, vht_enabled=0, bandwidth=40 MHz, cf1=2442
MHz, cf2=0 MHz)
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0x55a1155656c0 (wlan0), first=1)
wlan0: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0 (all)
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 94 f4
ec 38 c5 fd 94 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
Using interface wlan0 with hwaddr f4:ec:38:c5:fd:94 and ssid "dino-wpa1"
Deriving WPA PSK based on passphrase
SSID - hexdump_ascii(len=9):
64 69 6e 6f 2d 77 70 61 31 dino-wpa1
PSK (ASCII passphrase) - hexdump_ascii(len=32): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
random: Got 20/20 bytes from /dev/random
Get randomness: len=32 entropy=0
GMK - hexdump(len=32): [REMOVED]
Get randomness: len=32 entropy=0
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=60): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 94 f4 ec 38 c5 fd 94 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 09 64
69 6e 6f 2d 77 70 61 31 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=71): 2a 01 04 32 04 30 48 60 6c 30 18 01 00
00 0f ac 04 01 00 00 0f ac 04 02 00 00 0f ac 02 00 0f ac 06 0c 00 7f 08 00 00
00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03 a4 00 00 27 a4 00 00 42 43
5e 00 62 32 2f 00
nl80211: ifindex=4
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=9):
64 69 6e 6f 2d 77 70 61 31 dino-wpa1
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x1
nl80211: wpa_version=0x2
nl80211: key_mgmt_suites=0x102
nl80211: pairwise_ciphers=0x18
nl80211: group_cipher=0x10
nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
WPA: Start group state machine to set initial keys
WPA: group state machine entering state GTK_INIT (VLAN-ID 0)
Get randomness: len=16 entropy=0
GTK - hexdump(len=16): [REMOVED]
WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0)
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=3 addr=0x55a1135d9d81
key_idx=1 set_tx=1 seq_len=0 key_len=16
nl80211: KEY_DATA - hexdump(len=16): [REMOVED]
broadcast key
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
hostapd_setup_bss(hapd=0x55a11556a250 (wlan0_1), first=0)
nl80211: Create interface iftype 3 (AP)
nl80211: New interface wlan0_1 created: ifindex=51
nl80211: Add own interface ifindex 51
nl80211: if_indices[16]: 23 4 51
nl80211: Setup AP(wlan0_1) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x55a11556bdb0
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x55a11556bdb0
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x55a11556bdb0 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x55a11556bdb0 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x55a11556bdb0 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x55a11556bdb0 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x55a11556bdb0 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x55a11556bdb0 match=
nl80211: Add own interface ifindex 51
nl80211: ifindex 51 already in the list
wlan0: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0_1 (all)
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 95 f4
ec 38 c5 fd 95 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=51 (wlan0_1) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=51 (wlan0_1) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=51 (wlan0_1) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=51 (wlan0_1) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=51 (wlan0_1) alg=1 addr=(nil) key_idx=0
set_tx=1 seq_len=0 key_len=13
nl80211: KEY_DATA - hexdump(len=13): [REMOVED]
Using interface wlan0_1 with hwaddr f4:ec:38:c5:fd:95 and ssid "dino"
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=55): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 95 f4 ec 38 c5 fd 95 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 04 64
69 6e 6f 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=19): 2a 01 04 32 04 30 48 60 6c 7f 08 00 00
00 02 00 00 00 40
nl80211: ifindex=51
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=4):
64 69 6e 6f dino
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x3
nl80211: wpa_version=0x0
nl80211: key_mgmt_suites=0x2
nl80211: pairwise_ciphers=0x4
nl80211: group_cipher=0x4
nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: Set wlan0_1 operstate 1->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
hostapd_setup_bss(hapd=0x55a11556ad80 (wlan0_2), first=0)
nl80211: Create interface iftype 3 (AP)
nl80211: New interface wlan0_2 created: ifindex=52
nl80211: Add own interface ifindex 52
nl80211: if_indices[16]: 23 4 51 52
nl80211: Setup AP(wlan0_2) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x55a11556d060
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x55a11556d060
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x55a11556d060 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x55a11556d060 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x55a11556d060 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x55a11556d060 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x55a11556d060 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x55a11556d060 match=
nl80211: Add own interface ifindex 52
nl80211: ifindex 52 already in the list
wlan0: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0_2 (all)
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 96 f4
ec 38 c5 fd 96 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=52 (wlan0_2) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=52 (wlan0_2) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=52 (wlan0_2) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=52 (wlan0_2) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=52 (wlan0_2) alg=1 addr=(nil) key_idx=0
set_tx=1 seq_len=0 key_len=5
nl80211: KEY_DATA - hexdump(len=5): [REMOVED]
Using interface wlan0_2 with hwaddr f4:ec:38:c5:fd:96 and ssid "dino-guess"
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=61): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 96 f4 ec 38 c5 fd 96 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 0a 64
69 6e 6f 2d 67 75 65 73 73 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=19): 2a 01 04 32 04 30 48 60 6c 7f 08 00 00
00 02 00 00 00 40
nl80211: ifindex=52
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=10):
64 69 6e 6f 2d 67 75 65 73 73 dino-guess
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x3
nl80211: wpa_version=0x0
nl80211: key_mgmt_suites=0x2
nl80211: pairwise_ciphers=0x2
nl80211: group_cipher=0x2
nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: Set wlan0_2 operstate 1->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
wlan0: Setup of interface done.
ctrl_iface not configured!
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=2 linkmode=0 ifi_family=0
ifi_flags=0x1003 ([UP])
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=2 linkmode=0 ifi_family=0
ifi_flags=0x1003 ([UP])
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=2 linkmode=0 master=23
ifi_family=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=2 linkmode=0 master=23
ifi_family=0 ifi_flags=0x1003 ([UP])
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=2 ifi_family=7
ifi_flags=0x1003 ([UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=23 ifname=br-wifi operstate=6 linkmode=0 ifi_family=0
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
wlan0: Event INTERFACE_STATUS (5) received
Unknown event 5
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=6 ifi_family=7
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=6 ifi_family=7
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=6 ifi_family=7
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=6 linkmode=0 master=23
ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0)
VLAN: vlan_newlink(wl
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
rfkill: initial event: idx=1 type=2 op=0 soft=0 hard=0
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supported cipher 00-0f-ac:13
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Using driver-based off-channel TX
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Setup AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x557f75b990e0
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x557f75b990e0
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x557f75b990e0 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x557f75b990e0 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x557f75b990e0 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x557f75b990e0 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x557f75b990e0 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x557f75b990e0 match=
nl80211: Add own interface ifindex 23
nl80211: if_indices[16]: 23
nl80211: Add own interface ifindex 4
nl80211: if_indices[16]: 23 4
nl80211: Adding interface wlan0 into bridge br-wifi
phy: phy0
BSS count 3, BSSID mask ff:ff:ff:ff:ff:fc (2 bits)
nl80211: Regulatory information - country=98
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 25 MHz 20 mBm (no IR)
nl80211: 2474-2482 @ 8 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-59400 @ 2160 MHz 0 mBm
nl80211: 59400-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=13 freq=2472 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=13 freq=2472 MHz max_tx_power=20 dBm
Completing interface initialization
Mode: IEEE 802.11g Channel: 5 Frequency: 2432 MHz
DFS 0 channels required radar detection
nl80211: Set freq 2432 (ht_enabled=0, vht_enabled=0, bandwidth=40 MHz, cf1=2442
MHz, cf2=0 MHz)
* freq=2432
* vht_enabled=0
* ht_enabled=0
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0x557f75b9b680 (wlan0), first=1)
wlan0: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0 (all)
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 94 f4
ec 38 c5 fd 94 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
Using interface wlan0 with hwaddr f4:ec:38:c5:fd:94 and ssid "dino-wpa1"
Deriving WPA PSK based on passphrase
SSID - hexdump_ascii(len=9):
64 69 6e 6f 2d 77 70 61 31 dino-wpa1
PSK (ASCII passphrase) - hexdump_ascii(len=32): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
random: Got 20/20 bytes from /dev/random
Get randomness: len=32 entropy=0
GMK - hexdump(len=32): [REMOVED]
Get randomness: len=32 entropy=0
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=60): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 94 f4 ec 38 c5 fd 94 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 09 64
69 6e 6f 2d 77 70 61 31 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=71): 2a 01 04 32 04 30 48 60 6c 30 18 01 00
00 0f ac 04 01 00 00 0f ac 04 02 00 00 0f ac 02 00 0f ac 06 0c 00 7f 08 00 00
00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03 a4 00 00 27 a4 00 00 42 43
5e 00 62 32 2f 00
nl80211: ifindex=4
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=9):
64 69 6e 6f 2d 77 70 61 31 dino-wpa1
* beacon_int=100
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x1
nl80211: wpa_version=0x2
nl80211: key_mgmt_suites=0x102
nl80211: pairwise_ciphers=0x18
nl80211: group_cipher=0x10
nl80211: SMPS mode - dynamic
nl80211: beacon_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 00 00 00 02 00 00 00 40
nl80211: Beacon set failed: -22 (Invalid argument)
Failed to set beacon parameters
wlan0: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0 (all)
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 94 f4
ec 38 c5 fd 94 00 00 03 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
hostapd_free_hapd_data(wlan0)
Interface initialization failed
wlan0: interface state UNINITIALIZED->DISABLED
wlan0: AP-DISABLED
wlan0: Unable to setup interface.
hostapd_interface_deinit_free(0x557f75b9a720)
hostapd_interface_deinit_free: num_bss=3 conf->num_bss=3
hostapd_interface_deinit(0x557f75b9a720)
wlan0: interface state DISABLED->DISABLED
hostapd_bss_deinit: deinit bss wlan0_2
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 00 00 00 00 00 00 00
00 00 00 00 00 00 00 03 00
nl80211: Frame command failed: ret=-22 (Invalid argument) (freq=2432 wait=0)
wlan0: AP-DISABLED
hostapd_cleanup(hapd=0x557f75ba0c20 (wlan0_2))
hostapd_free_hapd_data: Interface wlan0_2 wasn't started
hostapd_bss_deinit: deinit bss wlan0_1
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff 00 00 00 00 00 00 00
00 00 00 00 00 00 00 03 00
nl80211: Frame command failed: ret=-22 (Invalid argument) (freq=2432 wait=0)
wlan0: AP-DISABLED
hostapd_cleanup(hapd=0x557f75ba00d0 (wlan0_1))
hostapd_free_hapd_data: Interface wlan0_1 wasn't started
hostapd_bss_deinit: deinit bss wlan0
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 94 f4
ec 38 c5 fd 94 00 00 03 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wlan0: AP-DISABLED
hostapd_cleanup(hapd=0x557f75b9b680 (wlan0))
hostapd_free_hapd_data: Interface wlan0 wasn't started
hostapd_interface_deinit_free: driver=0x557f741fdd00 drv_priv=0x557f75ba1770 ->
hapd_deinit
nl80211: deinit ifname=wlan0 disabled_11b_rates=0
nl80211: Remove monitor interface: refcount=0
nl80211: Remove beacon (ifindex=4)
netlink: Operstate: ifindex=4 linkmode=0 (kernel-control), operstate=6
(IF_OPER_UP)
nl80211: Set mode ifindex 4 iftype 2 (STATION)
nl80211: Teardown AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Unsubscribe mgmt frames handle 0x8888ddf7fd311869 (AP teardown)
hostapd_interface_free(0x557f75b9a720)
hostapd_interface_free: free hapd 0x557f75b9b680
hostapd_interface_free: free hapd 0x557f75ba00d0
hostapd_interface_free: free hapd 0x557f75ba0c20
hostapd_cleanup_iface(0x557f75b9a720)
hostapd_cleanup_iface_partial(0x557f75b9a720)
hostapd_cleanup_iface: free iface=0x557f75b9a720
random: Trying to read entropy from /dev/random
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supported cipher 00-0f-ac:13
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Using driver-based off-channel TX
nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00
00 00 00 00 00 00 40
nl80211: Driver-advertised extended capabilities mask (default) -
hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface wlan0 in phy phy0
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Setup AP(wlan0) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x5600c3dbf120
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x5600c3dbf120
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x5600c3dbf120 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x5600c3dbf120 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x5600c3dbf120 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x5600c3dbf120 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x5600c3dbf120 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=04
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=0501
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=0504
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=08
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=09
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=0a
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dbf120 match=7f
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
nl80211: Interface wlan0 is in bridge br-wifi
nl80211: Add own interface ifindex 23 (ifidx_reason 4)
nl80211: if_indices[16]: 23(4)
nl80211: Add own interface ifindex 4 (ifidx_reason -1)
nl80211: if_indices[16]: 23(4) 4(-1)
phy: phy0
BSS count 3, BSSID mask ff:ff:ff:ff:ff:fc (2 bits)
nl80211: Regulatory information - country=98
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 25 MHz 20 mBm (no IR)
nl80211: 2474-2482 @ 8 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 80 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 80 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-59400 @ 2160 MHz 0 mBm
nl80211: 59400-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=13 freq=2472 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=12 freq=2467 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=13 freq=2472 MHz max_tx_power=20 dBm
Completing interface initialization
Mode: IEEE 802.11g Channel: 5 Frequency: 2432 MHz
DFS 0 channels required radar detection
nl80211: Set freq 2432 (ht_enabled=0, vht_enabled=0, bandwidth=40 MHz, cf1=2442
MHz, cf2=0 MHz)
* freq=2432
* vht_enabled=0
* ht_enabled=0
* channel_type=0
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0x5600c3dc1710 (wlan0), first=1)
wlan0: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0 (all)
wlan0: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 94 f4
ec 38 c5 fd 94 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
Using interface wlan0 with hwaddr f4:ec:38:c5:fd:94 and ssid "dino-wpa1"
Deriving WPA PSK based on passphrase
SSID - hexdump_ascii(len=9):
64 69 6e 6f 2d 77 70 61 31 dino-wpa1
PSK (ASCII passphrase) - hexdump_ascii(len=32): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
random: Got 20/20 bytes from /dev/random
Get randomness: len=32 entropy=0
GMK - hexdump(len=32): [REMOVED]
Get randomness: len=32 entropy=0
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=60): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 94 f4 ec 38 c5 fd 94 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 09 64
69 6e 6f 2d 77 70 61 31 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=75): 2a 01 04 32 04 30 48 60 6c 30 18 01 00
00 0f ac 04 01 00 00 0f ac 04 02 00 00 0f ac 02 00 0f ac 06 0c 00 3b 02 53 00
7f 08 04 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03 a4 00 00 27 a4
00 00 42 43 5e 00 62 32 2f 00
nl80211: ifindex=4
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=9):
64 69 6e 6f 2d 77 70 61 31 dino-wpa1
* beacon_int=100
* dtim_period=2
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x1
nl80211: wpa_version=0x2
nl80211: key_mgmt_suites=0x102
nl80211: pairwise_ciphers=0x10
nl80211: group_cipher=0x10
nl80211: beacon_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
WPA: Start group state machine to set initial keys
WPA: group state machine entering state GTK_INIT (VLAN-ID 0)
Get randomness: len=16 entropy=0
GTK - hexdump(len=16): [REMOVED]
WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0)
wpa_driver_nl80211_set_key: ifindex=4 (wlan0) alg=3 addr=0x5600c21f5559
key_idx=1 set_tx=1 seq_len=0 key_len=16
nl80211: KEY_DATA - hexdump(len=16): [REMOVED]
broadcast key
nl80211: Set wlan0 operstate 0->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
hostapd_setup_bss(hapd=0x5600c3dc62a0 (wlan0_1), first=0)
nl80211: Create interface iftype 3 (AP)
nl80211: Ignored event (cmd=7) for foreign interface (ifindex 55 wdev 0x0)
nl80211: New interface wlan0_1 created: ifindex=55
nl80211: Add own interface ifindex 55 (ifidx_reason -1)
nl80211: if_indices[16]: 23(4) 4(-1) 55(-1)
nl80211: Setup AP(wlan0_1) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x5600c3dc8000
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x5600c3dc8000
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x5600c3dc8000 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x5600c3dc8000 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x5600c3dc8000 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x5600c3dc8000 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x5600c3dc8000 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=04
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=0501
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=0504
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=08
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=09
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=0a
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc8000 match=7f
nl80211: Add own interface ifindex 55 (ifidx_reason -1)
nl80211: ifindex 55 already in the list
wlan0_1: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0_1 (all)
wlan0_1: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 95 f4
ec 38 c5 fd 95 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=55 (wlan0_1) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=55 (wlan0_1) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=55 (wlan0_1) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=55 (wlan0_1) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=55 (wlan0_1) alg=1 addr=(nil) key_idx=0
set_tx=1 seq_len=0 key_len=13
nl80211: KEY_DATA - hexdump(len=13): [REMOVED]
Using interface wlan0_1 with hwaddr f4:ec:38:c5:fd:95 and ssid "dino"
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=55): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 95 f4 ec 38 c5 fd 95 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 04 64
69 6e 6f 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=23): 2a 01 04 32 04 30 48 60 6c 3b 02 53 00
7f 08 04 00 00 02 00 00 00 40
nl80211: ifindex=55
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=4):
64 69 6e 6f dino
* beacon_int=100
* dtim_period=2
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x3
nl80211: wpa_version=0x0
nl80211: key_mgmt_suites=0x4
nl80211: pairwise_ciphers=0x0
nl80211: group_cipher=0x4
nl80211: beacon_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: Set wlan0_1 operstate 1->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
hostapd_setup_bss(hapd=0x5600c3dc6e10 (wlan0_2), first=0)
nl80211: Create interface iftype 3 (AP)
nl80211: Ignored event (cmd=7) for foreign interface (ifindex 56 wdev 0x0)
nl80211: New interface wlan0_2 created: ifindex=56
nl80211: Add own interface ifindex 56 (ifidx_reason -1)
nl80211: if_indices[16]: 23(4) 4(-1) 55(-1) 56(-1)
nl80211: Setup AP(wlan0_2) - device_ap_sme=0 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x5600c3dc9990
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x5600c3dc9990
match=
nl80211: Register frame type=0x0 (WLAN_FC_STYPE_ASSOC_REQ)
nl_handle=0x5600c3dc9990 match=
nl80211: Register frame type=0x20 (WLAN_FC_STYPE_REASSOC_REQ)
nl_handle=0x5600c3dc9990 match=
nl80211: Register frame type=0xa0 (WLAN_FC_STYPE_DISASSOC)
nl_handle=0x5600c3dc9990 match=
nl80211: Register frame type=0xc0 (WLAN_FC_STYPE_DEAUTH)
nl_handle=0x5600c3dc9990 match=
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ)
nl_handle=0x5600c3dc9990 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=04
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=0501
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=0504
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=06
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=08
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=09
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=0a
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=11
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION)
nl_handle=0x5600c3dc9990 match=7f
nl80211: Add own interface ifindex 56 (ifidx_reason -1)
nl80211: ifindex 56 already in the list
wlan0_2: Flushing old station entries
nl80211: flush -> DEL_STATION wlan0_2 (all)
wlan0_2: Deauthenticate all stations
nl80211: send_mlme - da= ff:ff:ff:ff:ff:ff noack=0 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0xc0 (WLAN_FC_STYPE_DEAUTH) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=26): c0 00 00 00 ff ff ff ff ff ff f4 ec 38 c5 fd 96 f4
ec 38 c5 fd 96 00 00 02 00
nl80211: Frame command failed: ret=-16 (Device or resource busy) (freq=2432
wait=0)
wpa_driver_nl80211_set_key: ifindex=56 (wlan0_2) alg=0 addr=(nil) key_idx=0
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=56 (wlan0_2) alg=0 addr=(nil) key_idx=1
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=56 (wlan0_2) alg=0 addr=(nil) key_idx=2
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=56 (wlan0_2) alg=0 addr=(nil) key_idx=3
set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=56 (wlan0_2) alg=1 addr=(nil) key_idx=0
set_tx=1 seq_len=0 key_len=5
nl80211: KEY_DATA - hexdump(len=5): [REMOVED]
Using interface wlan0_2 with hwaddr f4:ec:38:c5:fd:96 and ssid "dino-guess"
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=61): 80 00 00 00 ff ff ff ff ff ff f4 ec 38
c5 fd 96 f4 ec 38 c5 fd 96 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 0a 64
69 6e 6f 2d 67 75 65 73 73 01 08 82 84 8b 96 0c 12 18 24 03 01 05
nl80211: Beacon tail - hexdump(len=23): 2a 01 04 32 04 30 48 60 6c 3b 02 53 00
7f 08 04 00 00 02 00 00 00 40
nl80211: ifindex=56
nl80211: beacon_int=100
nl80211: dtim_period=2
nl80211: ssid - hexdump_ascii(len=10):
64 69 6e 6f 2d 67 75 65 73 73 dino-guess
* beacon_int=100
* dtim_period=2
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x3
nl80211: wpa_version=0x0
nl80211: key_mgmt_suites=0x4
nl80211: pairwise_ciphers=0x0
nl80211: group_cipher=0x2
nl80211: beacon_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: proberesp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: assocresp_ies - hexdump(len=10): 7f 08 04 00 00 02 00 00 00 40
nl80211: Set wlan0_2 operstate 1->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
wlan0: interface state UNINITIALIZED->ENABLED
wlan0: AP-ENABLED
wlan0: Setup of interface done.
ctrl_iface not configured!
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=6 ifi_family=7
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23 (ifidx_reason 4)
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=6 ifi_family=7
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23 (ifidx_reason 4)
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=4 ifname=wlan0 master=23 operstate=6 ifi_family=7
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 23 for bridge br-wifi
nl80211: Add own interface ifindex 23 (ifidx_reason 4)
nl80211: ifindex 23 already in the list
RTM_NEWLINK: ifi_index=4 ifname=wlan0 operstate=6 linkmode=0 master=23
ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 operstate=2 linkmode=0 ifi_family=0
ifi_flags=0x1002 ()
nl80211: Ignore interface down event since interface wlan0_1 is up
RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 operstate=2 linkmode=0 ifi_family=0
ifi_flags=0x1002 ()
nl80211: Ignore interface down event since interface wlan0_1 is up
RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 operstate=0 linkmode=0 ifi_family=0
ifi_flags=0x1043 ([UP][RUNNING])
wlan0: Event INTERFACE_STATUS (5) received
Unknown event 5
RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 operstate=6 linkmode=0 ifi_family=0
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
wlan0: Event INTERFACE_STATUS (5) received
Unknown event 5
RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 operstate=2 linkmode=0 ifi_family=0
ifi_flags=0x1002 ()
nl80211: Ignore interface down event since interface wlan0_2 is up
RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 operstate=2 linkmode=0 ifi_family=0
ifi_flags=0x1002 ()
nl80211: Ignore interface down event since interface wlan0_2 is up
VLAN: RTM_NEWLINK: ifi_index=4 ifname=wlan0 ifi_family=7 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0)
VLAN: RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0_1)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0_2)
RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 operstate=0 linkmode=0 ifi_family=0
ifi_flags=0x1043 ([UP][RUNNING])
wlan0: Event INTERFACE_STATUS (5) received
Unknown event 5
RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 operstate=6 linkmode=0 ifi_family=0
ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
wlan0: Event INTERFACE_STATUS (5) received
Unknown event 5
VLAN: RTM_NEWLINK: ifi_index=4 ifname=wlan0 ifi_family=7 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x1002 ()
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=4 ifname=wlan0 ifi_family=7 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x1002 ()
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=4 ifname=wlan0 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x1043
([UP][RUNNING])
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 ifi_family=0 ifi_flags=0x1002 ()
VLAN: vlan_newlink(wlan0_1)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 ifi_family=0 ifi_flags=0x1002 ()
VLAN: vlan_newlink(wlan0_1)
VLAN: RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 ifi_family=0 ifi_flags=0x1043
([UP][RUNNING])
VLAN: vlan_newlink(wlan0_1)
VLAN: RTM_NEWLINK: ifi_index=55 ifname=wlan0_1 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0_1)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x1002 ()
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x1002 ()
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x1043
([UP][RUNNING])
VLAN: vlan_newlink(wlan0_2)
VLAN: RTM_NEWLINK: ifi_index=56 ifname=wlan0_2 ifi_family=0 ifi_flags=0x11043
([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(wlan0_2)
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on wlan0(f4:ec:38:c5:fd:94)
A1=ff:ff:ff:ff:ff:ff A2=c0:c9:76:bc:19:79
nl80211: MLME event frame - hexdump(len=203): 40 00 00 00 ff ff ff ff ff ff c0
c9 76 bc 19 79 ff ff ff ff ff ff 50 bf 00 00 01 08 82 84 8b 96 0c 12 18 24 32
04 30 48 60 6c 7f 04 00 00 0a 02 dd 86 00 50 f2 04 10 4a 00 01 10 10 3a 00 01
00 10 08 00 02 42 88 10 47 00 10 0d 02 81 d9 e5 46 5b bf 95 85 6e c1 f5 84 02
ef 10 54 00 08 00 0a 00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 00 10 09
00 02 00 00 10 12 00 02 00 00 10 21 00 04 57 49 4b 4f 10 23 00 0b 55 20 46 45
45 4c 20 4c 49 54 45 10 24 00 0b 55 20 46 45 45 4c 20 4c 49 54 45 10 11 00 07
50 34 36 30 31 41 4e 10 49 00 06 00 37 2a 00 01 20 dd 11 50 6f 9a 09 02 02 00
25 00 06 05 00 46 52 04 51 0b
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=c0:c9:76:bc:19:79
bssid=ff:ff:ff:ff:ff:ff freq=2432 ssi_signal=-89 fc=0x40 seq_ctrl=0xbf50
stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=203
nl80211: send_mlme - da= c0:c9:76:bc:19:79 noack=1 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=135): 50 00 00 00 c0 c9 76 bc 19 79 f4 ec 38 c5 fd 94
f4 ec 38 c5 fd 94 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 09 64 69 6e 6f
2d 77 70 61 31 01 08 82 84 8b 96 0c 12 18 24 03 01 05 2a 01 04 32 04 30 48 60
6c 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04 02 00 00 0f ac 02 00 0f ac 06 0c
00 3b 02 53 00 7f 08 04 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03
a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan0_1
nl80211: MLME event 59 (NL80211_CMD_FRAME) on wlan0_1(f4:ec:38:c5:fd:95)
A1=ff:ff:ff:ff:ff:ff A2=c0:c9:76:bc:19:79
nl80211: MLME event frame - hexdump(len=203): 40 00 00 00 ff ff ff ff ff ff c0
c9 76 bc 19 79 ff ff ff ff ff ff 50 bf 00 00 01 08 82 84 8b 96 0c 12 18 24 32
04 30 48 60 6c 7f 04 00 00 0a 02 dd 86 00 50 f2 04 10 4a 00 01 10 10 3a 00 01
00 10 08 00 02 42 88 10 47 00 10 0d 02 81 d9 e5 46 5b bf 95 85 6e c1 f5 84 02
ef 10 54 00 08 00 0a 00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 00 10 09
00 02 00 00 10 12 00 02 00 00 10 21 00 04 57 49 4b 4f 10 23 00 0b 55 20 46 45
45 4c 20 4c 49 54 45 10 24 00 0b 55 20 46 45 45 4c 20 4c 49 54 45 10 11 00 07
50 34 36 30 31 41 4e 10 49 00 06 00 37 2a 00 01 20 dd 11 50 6f 9a 09 02 02 00
25 00 06 05 00 46 52 04 51 0b
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=c0:c9:76:bc:19:79
bssid=ff:ff:ff:ff:ff:ff freq=2432 ssi_signal=-89 fc=0x40 seq_ctrl=0xbf50
stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=203
nl80211: send_mlme - da= c0:c9:76:bc:19:79 noack=1 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=78): 50 00 00 00 c0 c9 76 bc 19 79 f4 ec 38 c5 fd 95 f4
ec 38 c5 fd 95 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 04 64 69 6e 6f 01
08 82 84 8b 96 0c 12 18 24 03 01 05 2a 01 04 32 04 30 48 60 6c 3b 02 53 00 7f
08 04 00 00 02 00 00 00 40
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan0_2
nl80211: MLME event 59 (NL80211_CMD_FRAME) on wlan0_2(f4:ec:38:c5:fd:96)
A1=ff:ff:ff:ff:ff:ff A2=c0:c9:76:bc:19:79
nl80211: MLME event frame - hexdump(len=203): 40 00 00 00 ff ff ff ff ff ff c0
c9 76 bc 19 79 ff ff ff ff ff ff 50 bf 00 00 01 08 82 84 8b 96 0c 12 18 24 32
04 30 48 60 6c 7f 04 00 00 0a 02 dd 86 00 50 f2 04 10 4a 00 01 10 10 3a 00 01
00 10 08 00 02 42 88 10 47 00 10 0d 02 81 d9 e5 46 5b bf 95 85 6e c1 f5 84 02
ef 10 54 00 08 00 0a 00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 00 10 09
00 02 00 00 10 12 00 02 00 00 10 21 00 04 57 49 4b 4f 10 23 00 0b 55 20 46 45
45 4c 20 4c 49 54 45 10 24 00 0b 55 20 46 45 45 4c 20 4c 49 54 45 10 11 00 07
50 34 36 30 31 41 4e 10 49 00 06 00 37 2a 00 01 20 dd 11 50 6f 9a 09 02 02 00
25 00 06 05 00 46 52 04 51 0b
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=c0:c9:76:bc:19:79
bssid=ff:ff:ff:ff:ff:ff freq=2432 ssi_signal=-89 fc=0x40 seq_ctrl=0xbf50
stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=203
nl80211: send_mlme - da= c0:c9:76:bc:19:79 noack=1 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=84): 50 00 00 00 c0 c9 76 bc 19 79 f4 ec 38 c5 fd 96 f4
ec 38 c5 fd 96 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 0a 64 69 6e 6f 2d
67 75 65 73 73 01 08 82 84 8b 96 0c 12 18 24 03 01 05 2a 01 04 32 04 30 48 60
6c 3b 02 53 00 7f 08 04 00 00 02 00 00 00 40
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on wlan0(f4:ec:38:c5:fd:94)
A1=ff:ff:ff:ff:ff:ff A2=c0:c9:76:bc:19:79
nl80211: MLME event frame - hexdump(len=203): 40 00 00 00 ff ff ff ff ff ff c0
c9 76 bc 19 79 ff ff ff ff ff ff 60 bf 00 00 01 08 82 84 8b 96 0c 12 18 24 32
04 30 48 60 6c 7f 04 00 00 0a 02 dd 86 00 50 f2 04 10 4a 00 01 10 10 3a 00 01
00 10 08 00 02 42 88 10 47 00 10 0d 02 81 d9 e5 46 5b bf 95 85 6e c1 f5 84 02
ef 10 54 00 08 00 0a 00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 00 10 09
00 02 00 00 10 12 00 02 00 00 10 21 00 04 57 49 4b 4f 10 23 00 0b 55 20 46 45
45 4c 20 4c 49 54 45 10 24 00 0b 55 20 46 45 45 4c 20 4c 49 54 45 10 11 00 07
50 34 36 30 31 41 4e 10 49 00 06 00 37 2a 00 01 20 dd 11 50 6f 9a 09 02 02 00
25 00 06 05 00 46 52 04 51 0b
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=c0:c9:76:bc:19:79
bssid=ff:ff:ff:ff:ff:ff freq=2432 ssi_signal=-88 fc=0x40 seq_ctrl=0xbf60
stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=203
nl80211: send_mlme - da= c0:c9:76:bc:19:79 noack=1 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=135): 50 00 00 00 c0 c9 76 bc 19 79 f4 ec 38 c5 fd 94
f4 ec 38 c5 fd 94 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 09 64 69 6e 6f
2d 77 70 61 31 01 08 82 84 8b 96 0c 12 18 24 03 01 05 2a 01 04 32 04 30 48 60
6c 30 18 01 00 00 0f ac 04 01 00 00 0f ac 04 02 00 00 0f ac 02 00 0f ac 06 0c
00 3b 02 53 00 7f 08 04 00 00 02 00 00 00 40 dd 18 00 50 f2 02 01 01 00 00 03
a4 00 00 27 a4 00 00 42 43 5e 00 62 32 2f 00
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan0_1
nl80211: MLME event 59 (NL80211_CMD_FRAME) on wlan0_1(f4:ec:38:c5:fd:95)
A1=ff:ff:ff:ff:ff:ff A2=c0:c9:76:bc:19:79
nl80211: MLME event frame - hexdump(len=203): 40 00 00 00 ff ff ff ff ff ff c0
c9 76 bc 19 79 ff ff ff ff ff ff 60 bf 00 00 01 08 82 84 8b 96 0c 12 18 24 32
04 30 48 60 6c 7f 04 00 00 0a 02 dd 86 00 50 f2 04 10 4a 00 01 10 10 3a 00 01
00 10 08 00 02 42 88 10 47 00 10 0d 02 81 d9 e5 46 5b bf 95 85 6e c1 f5 84 02
ef 10 54 00 08 00 0a 00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 00 10 09
00 02 00 00 10 12 00 02 00 00 10 21 00 04 57 49 4b 4f 10 23 00 0b 55 20 46 45
45 4c 20 4c 49 54 45 10 24 00 0b 55 20 46 45 45 4c 20 4c 49 54 45 10 11 00 07
50 34 36 30 31 41 4e 10 49 00 06 00 37 2a 00 01 20 dd 11 50 6f 9a 09 02 02 00
25 00 06 05 00 46 52 04 51 0b
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=c0:c9:76:bc:19:79
bssid=ff:ff:ff:ff:ff:ff freq=2432 ssi_signal=-88 fc=0x40 seq_ctrl=0xbf60
stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=203
nl80211: send_mlme - da= c0:c9:76:bc:19:79 noack=1 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=78): 50 00 00 00 c0 c9 76 bc 19 79 f4 ec 38 c5 fd 95 f4
ec 38 c5 fd 95 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 04 64 69 6e 6f 01
08 82 84 8b 96 0c 12 18 24 03 01 05 2a 01 04 32 04 30 48 60 6c 3b 02 53 00 7f
08 04 00 00 02 00 00 00 40
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for wlan0_2
nl80211: MLME event 59 (NL80211_CMD_FRAME) on wlan0_2(f4:ec:38:c5:fd:96)
A1=ff:ff:ff:ff:ff:ff A2=c0:c9:76:bc:19:79
nl80211: MLME event frame - hexdump(len=203): 40 00 00 00 ff ff ff ff ff ff c0
c9 76 bc 19 79 ff ff ff ff ff ff 60 bf 00 00 01 08 82 84 8b 96 0c 12 18 24 32
04 30 48 60 6c 7f 04 00 00 0a 02 dd 86 00 50 f2 04 10 4a 00 01 10 10 3a 00 01
00 10 08 00 02 42 88 10 47 00 10 0d 02 81 d9 e5 46 5b bf 95 85 6e c1 f5 84 02
ef 10 54 00 08 00 0a 00 50 f2 04 00 05 10 3c 00 01 01 10 02 00 02 00 00 10 09
00 02 00 00 10 12 00 02 00 00 10 21 00 04 57 49 4b 4f 10 23 00 0b 55 20 46 45
45 4c 20 4c 49 54 45 10 24 00 0b 55 20 46 45 45 4c 20 4c 49 54 45 10 11 00 07
50 34 36 30 31 41 4e 10 49 00 06 00 37 2a 00 01 20 dd 11 50 6f 9a 09 02 02 00
25 00 06 05 00 46 52 04 51 0b
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=c0:c9:76:bc:19:79
bssid=ff:ff:ff:ff:ff:ff freq=2432 ssi_signal=-88 fc=0x40 seq_ctrl=0xbf60
stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=203
nl80211: send_mlme - da= c0:c9:76:bc:19:79 noack=1 freq=0 no_cck=0 offchanok=0
wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: send_mlme -> send_frame
nl80211: send_frame - Use bss->freq=2432
nl80211: send_frame -> send_frame_cmd
nl80211: CMD_FRAME freq=2432 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=84): 50 00 00 00 c0 c9 76 bc 19 79 f4 ec 38 c5 fd 96 f4
ec 38 c5 fd 96 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 0a 64 69 6e 6f 2d
67 75 65 73 73 01 08 82 84 8b 96 0c 12 18 24 03 01 05 2a 01 04 32 04 30 48 60
6c 3b 02 53 00 7f 08 04 00 00 02 00 00 00 40
nl80211: Frame TX command accepted (no ACK); cookie 0x0