Package: cdrom Severity: grave Justification: renders package unusable I'm trying to install debian etch, so I downloaded this iso http://ftp.br.debian.org/debian-cd/4.0_r0/i386/iso-cd/debian-40r0-i386-CD-1.iso and burned it in a CD. When I try to install it, I can't go any further than the DETECT AND MOUNT CDROM, cause the CD-ROM drive was not detected, i've tried loading all modules sugested but none where able to make the cdrom usable.
So I tried using NETBOOT.tar.gz to install the base system, to bypass the CDROM step. I managed to get to the partition HD, but again the installer would not detect my HD, so I couldn't partition/Install nothing. I've entered this trouble in debian-user-portuguese, and a user recommended booting using these parameters, BOOT_DEBUG=3 echo options libata atapi_enabled=1 >> /etc/modprobe.conf echo ide-generic >> /etc/modprobe.conf echo ata_piix >> /etc/modprobe.conf echo sd_mod >> /etc/modprobe.conf Despite the user's good will, none was efective, I still can get my cd-rom detected. Thank you my notebook is a Acer Apire 7104WSMi: Celeron M 1.6, 512Mb RAM LSPCI attached ------------------------------ 00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03) 00:02.0 VGA compatible controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) 00:02.1 Display controller: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller (rev 03) 00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3) 00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03) 00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03) 06:05.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02) 06:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 06:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev 01) end LSPCI --------- DMESG ATTACHED -------- Port Service[0000:00:1c.0:pcie00] Allocate Port Service[0000:00:1c.0:pcie02] Allocate Port Service[0000:00:1c.0:pcie03] vesafb: framebuffer at 0xc0000000, mapped to 0xe0080000, using 1875k, total 7872k vesafb: mode is 800x600x16, linelength=1600, pages=7 vesafb: protected mode interface info at 00ff:44f0 vesafb: scrolling: redraw vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 100x37 fb0: VESA VGA frame buffer device isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize PNP: PS/2 Controller [PNP0303:KBD0,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 mice: PS/2 mouse device common for all mice EISA: Probing bus 0 at eisa.0 Cannot allocate resource for EISA slot 1 Cannot allocate resource for EISA slot 2 Cannot allocate resource for EISA slot 3 EISA: Detected 0 cards. TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 8 NET: Registered protocol family 20 Using IPI Shortcut mode ACPI: (supports S0 S3 S4 S5) Time: tsc clocksource has been installed. Freeing unused kernel memory: 256k freed usbcore: registered new driver usbfs usbcore: registered new driver hub USB Universal Host Controller Interface driver v3.0 ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 201 PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: UHCI Host Controller uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 uhci_hcd 0000:00:1d.0: irq 201, io base 0x00001820 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected SCSI subsystem initialized libata version 2.00 loaded. ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: UHCI Host Controller uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:1d.1: irq 169, io base 0x00001840 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 209 PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: UHCI Host Controller uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:1d.2: irq 209, io base 0x00001860 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected input: AT Translated Set 2 keyboard as /class/input/input0 ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 217 PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: UHCI Host Controller uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:1d.3: irq 217, io base 0x00001880 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 201 PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: EHCI Host Controller ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5 ehci_hcd 0000:00:1d.7: debug port 1 PCI: cache line size of 32 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: irq 201, io mem 0xb0004000 ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 8 ports detected ata_piix 0000:00:1f.2: version 2.00 ata_piix 0000:00:1f.2: MAP [ XX XX XX XX ] ata_piix 0000:00:1f.2: invalid MAP value 1 ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 17 (level, low) -> IRQ 169 PCI: Setting latency timer of device 0000:00:1f.2 to 64 ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x1810 irq 14 scsi0 : ata_piix ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1818 irq 15 scsi1 : ata_piix ATA: abnormal status 0x7F on port 0x177 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Yenta: CardBus bridge found at 0000:06:09.0 [1025:0100] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:06:09.0, mfunc 0x00001022, devctl 0x44 Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000 input: SynPS/2 Synaptics TouchPad as /class/input/input1 Yenta: ISA IRQ mask 0x04f8, PCI irq 177 Socket status: 30000006 Yenta: Raising subordinate bus# of parent bus (#06) from #07 to #0a pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff cs: IO port probe 0x3000-0x3fff: clean. pcmcia: parent PCI bridge Memory window: 0xb8000000 - 0xb80fffff pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x31ffffff cs: IO port probe 0x100-0x3af: excluding 0x370-0x377 cs: IO port probe 0x3e0-0x4ff: excluding 0x3f0-0x3f7 0x4d0-0x4d7 cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) ACPI: Processor [CPU0] (supports 8 throttling states) ACPI: Getting cpuindex for acpiid 0x1 Time: acpi_pm clocksource has been installed. ACPI: Thermal Zone [TZS0] (51 C) ACPI: Thermal Zone [TZS1] (51 C) Synaptics Touchpad, model: 1, fw: 6.2, id: 0x12a0b1, caps: 0xa04713/0x204000 input: SynPS/2 Synaptics TouchPad as /class/input/input2 psmouse.c: TouchPad at isa0060/serio4/input0 lost sync at byte 1 usbcore: registered new driver usbkbd drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver usbcore: registered new driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core vga16fb: initializing vga16fb: mapped to 0xc00a0000 fb1: VGA16 VGA frame buffer device usbcore: registered new driver usbmouse drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. psmouse.c: TouchPad at isa0060/serio4/input0 - driver resynched. floppy0: no floppy controllers found ide0: I/O resource 0x1F0-0x1F7 not free. ide0: ports already in use, skipping probe ide1: I/O resource 0x170-0x177 not free. ide1: ports already in use, skipping probe end dmesg ---------------------------------------- -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of "unsubscribe". Trouble? Contact [EMAIL PROTECTED]