Hi, Sven. On Aug 22 2008, Sven Luther wrote: > On Fri, Aug 22, 2008 at 09:14:04AM -0300, Rogério Brito wrote: > > Since this is my first incursion into the embedded arena, I would welcome > > any help (and, BTW, learn and collaborate with the emdebian project with my > > own packages). > > > > It seems to me that a special kernel should be compiled, that special > > devices should be created (apparently, the current udev/kernels don't > > create the necessary devices needed so that the device doesn't shuts down > > automatically) and that some daemons specific to the kurobox (and variants) > > should be packaged. > > Can you get access to the dmesg output of this board, or otherwise can > tell us what cpu is used inside ?
Sure, the dmesg is attached here. > Also i suppose it uses uboot or another similar bootloader, debian > currently has no support for this, but there is some basic uboot support > for arm based devices, didn't follow this lately. Yes, it seems to be able to boot with uboot, yes. But it needs some packages specific to the kurobox (and other Linkstation boxes), like the heartbeat daemon that I mentioned on the earlier message. Some init scripts also seem to be needed. > Please forward this mail to the list, since i am being censored and > can't post directly. No problems (you still can't post to the lists?). Anyway, even if you can't post, please, keep the Cc'ies, please. Regards, Rogério Brito. -- Rogério Brito : [EMAIL PROTECTED],ime.usp}.br : GPG key 1024D/7C2CAEB8 http://www.ime.usp.br/~rbrito : http://meusite.mackenzie.com.br/rbrito Projects: algorithms.berlios.de : lame.sf.net : vrms.alioth.debian.org
Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb Linux version 2.4.17_kuro-box ([EMAIL PROTECTED]) (gcc version 2.95.3 20010315 (release/MontaVista)) #2 2004ǯ 3·î 18Æü ÌÚÍËÆü 11:39:47 JST KURO-BOX (C) 2004 KUROUTO-SHIKOU. On node 0 totalpages: 16384 zone(0): 16384 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/hda1 OpenPIC Version 1.2 (1 CPUs and 139 IRQ sources) at 80040000 decrementer frequency = 24.362848 MHz rtc sec count 1219405372 Calibrating delay loop... 129.84 BogoMIPS Memory: 60532k available (1124k kernel code, 520k data, 188k init, 0k highmem) Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes) Inode-cache hash table entries: 4096 (order: 3, 32768 bytes) Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes) Page-cache hash table entries: 16384 (order: 4, 65536 bytes) POSIX conformance testing by UNIFIX PCI: Probing PCI hardware Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Disabling the Out Of Memory Killer Journalled Block Device driver loaded pty: 256 Unix98 ptys configured BUFFALO INC. RTC driver ver 1.00 Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x80004600 (irq = 138) is a 16550A ttyS01 at 0x80004500 (irq = 137) is a 16550A block: 128 slots per queue, batch=32 RAMDISK driver initialized: 16 RAM disks of 10000K size 1024 blocksize Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx CMD680: IDE controller on PCI bus 00 dev 60 CMD680: chipset revision 2 CMD680: 100% native mode on irq 17 ide0: BM-DMA at 0xbffed0-0xbffed7, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0xbffed8-0xbffedf, BIOS settings: hdc:pio, hdd:pio hda: HDS722516VLAT20, ATA DISK drive ide0 at 0xbffef8-0xbffeff,0xbffef6 on irq 17 hda: 321672960 sectors (164697 MB) w/1794KiB Cache, CHS=20023/255/63, UDMA(100) Partition check: hda: hda1 hda2 hda3 loop: loaded (max 8 devices) FLASHDISK:Initialized [FUJITSU MBM29PL32TM] Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001) tulip0: MII transceiver #1 config 3100 status 7849 advertising 05e1. eth0: ADMtek Comet rev 17 at 0xbfff00, 00:07:40:FB:20:D7, IRQ 16. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 4096 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. NET4: AppleTalk 0.18a for Linux NET4.0 RAMDISK: Compressed image found at block 0 Freeing initrd memory: 2077k freed Boot from /dev/hda1. EXT2-fs warning: checktime reached, running e2fsck is recommended VFS: Mounted root (ext2 filesystem). Boot from /dev/hda1. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem) readonly. change_root: old root has d_count=2 Trying to unmount old root ... okay Freeing unused kernel memory: 188k init Adding Swap: 257032k swap-space (priority -1) EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,1), internal journal kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.17, 10 Jan 2002 on ide0(3,3), internal journal EXT3-fs: mounted filesystem with ordered data mode. usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xc503a000, IRQ 19 usb-ohci.c: usb-00:0e.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 3 ports detected usb-ohci.c: USB OHCI at membase 0xc503c000, IRQ 19 usb-ohci.c: usb-00:0e.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 2 ports detected hcd.c: ehci-hcd @ 00:0e.2, PCI device 1033:00e0 (NEC Corporation) hcd.c: irq 19, pci mem c5044f00 usb.c: new USB bus registered, assigned bus number 3 ehci-hcd.c: USB 2.0 support enabled, EHCI rev 1. 0 hub.c: USB hub found hub.c: 5 ports detected SCSI subsystem driver Revision: 1.00 Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage USB Mass Storage support registered. usb.c: registered new driver usblp printer.c: v0.11: USB Printer Device Class driver